HIKVISION DS-PDTT15AM-LM Wired Triple Signal Detector User Manual

HIKVISION DS-PDTT15AM-LM Wired Triple Signal Detector

Appearance

1. Top/Bottom Cover
2. Front Panel
3. PCBA
4. Rear Panel

The Main Printed Circuit Board Assembly (PCBA)

1. Tamper Switch
2. Bottom PIR Sensor
3. EOL Resistance
4. Terminal
5. Normal Open Terminal
6. DIP Switch
7. Microwave Potentiometer
8. PIR Angle PIR
   • Triggered:
   • (top) PIR Triggered:
   • (top) MW Triggered:
   • Alarm: Masked
   • : + Fault:

Detection Range

1. Detection range
2. PIR Angle
3. PIR Distance
4. Masking seal

Installation

Relay Status

| Normal| Alarm| Fault| Mask| Tamper
---|---|---|---|---|---
Alarm Relay| Close| Open| Close| Open| Close
Fault Relay| Close| Close| Open| Open| Close
Tamper Relay| Close| Close| Close| Close| Open

Resistor Wiring

Method 1: Use the jumper to select EOL (End of Line) resistance on TAMPER/ALARM/FAULT pins. Method 2: Add the resistor to TAMPER/ALARM/FAULT wiring ports. Note: If EOL wiring is not used, leave the jumpers OFF. Do not force the jumper if it is not matched the  pin. Method 1 & 2 should not be used on the ALARM/TAMPER/FAULT at the same time.

1. Tamper Resistance: 1K, 2K2, 4K7, 5K6, 6K8
2. Alarm Resistance: 1K, 2K2, 4K7, 5K6, 6K8
3. Fault Resistance: 1K, 2K2, 4K7, 5K6, 6K8

Connection Type

1. Normally Closed
   Note: The resistor must be connected in series with one end of the detector.

2. Single End of Line Wiring

3. Double End of Line Wiring

4. Triple End of Line Wiring

Remote LED Enable

Note: To use this feature, the LED switch must be OFF.

Anti-masking
Lighting

Normal Open Terminal
≤350 mA 60 VDC, Contact Resistance <8 Ω

Powering On

Specification

Digital Temperature

Compensation

| Support
Anti-masking| Support
Adaptable Coverage| Support
Pattern mask included
Digital Processing| Tri-Signal Logic
Sealed Optics| Support
Tamper Protection| Front, Rear
Anti-Sway Analytics| Support
Alarm Output| Normally Closed

LED Indicator

| Green(Top PIR), Red(Microwave), Orange(Bottom PIR), Green+ Orange(Mask), Blue(Alarm)
Power Consumption| 220 mA Max (with lighting on), 60mA

(standard)

Power Supply| 9 to 16 VDC
Typical Voltage| 12 VDC
Operation Temperature| -25 °C to 60 °C (-13 °F to 140 °F)
Storage Temperature| -25 °C to 60 °C (-13 °F to 140 °F)
Operation Humidity| 10% to 90%
IP Rate| IP65
Dimension(W × H × D)| 75 mm × 202 mm × 73 mm
Weight| 350 g
Mounting Height| 0.8 to 1.2 m
Mounting Method| Wall
Application Scenario| Outdoor

Please use the power adapter complaining with LPS. The recommended power adapter is made by Shenzhen Honor Electronic Co., Ltd.

TO THE MAXIMUMEXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITSHARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS ATYOUR OWN RISK. IN NO EVENT WILLHIKVISION BE LIABLE TO YOUFOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONGOTHERS, DAMAGES FOR LOSS OFBUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ONBREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE),PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OFTHE PRODUCT, EVEN IF HIKVISIONHAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGESOR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENTSECURITY RISKS, ANDHIKVISION SHALL NOT TAKEANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OROTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICALSUPPORT IF REQUIRED. YOU AGREE TOUSE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, ANDYOU ARE SOLELY RESPONSIBLEFOR ENSURING THAT YOUR USE CONFORMS TOTHE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OFPUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS.YOU SHALL NOT USE THISPRODUCT FOR ILLEGAL HUNTING ANIMALS, INVASION OFPRIVACY OR ANY OTHER PURPOSE WHICH ISILLEGAL OR DETRIMENTAL TOTHE PUBLIC INTEREST. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTIONOF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT ORPRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS,ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMANRIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUALAND THE APPLICABLELAW, THE LATER PREVAILS.

FCC compliance:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment offending, the users encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or inexperienced radio/TV technician for help

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device mayn’t cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation

References

• Hikvision - Leading Video AIoT Solutions & Services Provider
• HOME
• Hikvision USA - Leading the future of AIoT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>