AVIANCE HD00834 3 Light Black Cast Brass Hardwried Outdoor Installation Guide
- July 3, 2024
- AVIANCE
Table of Contents
AVIANCE HD00834 3 Light Black Cast Brass Hardwired Outdoor
Specifications:
- Model: HD00834
- Power Source : Electrical
- Bulb Requirement : Not Included
- Maximum Wattage Rating : Refer to fixture specifications
Product Usage Instructions
Assembling the Fixture:
- Shut off the power at the circuit breaker and remove the old fixture, including the single bar.
- Unpack the new fixture and lay out all parts on a clear area, ensuring not to lose any small parts needed for installation.
- Place the candle sleeve over the lamp holder.
- Install light bulbs (not included) according to the fixture’s specifications, ensuring not to exceed the maximum wattage rating.
- Attach the pipe thread into the shade of the lamp body, aligning the box top center screw hole with the pipe thread, and secure it by turning it clockwise until tight. Attach the cove to the lamp body, then lock it securely with the loop.
- Attach the assembled lamp body onto the post (not included) and secure it with screws.
Connecting the Wires:
- Connect the electrical wires by matching black fixture wire to black house wire (hot), and white fixture wire to white house wire (neutral). Ensure all wire nuts are secured and consider wrapping connections with electrical tape.
- If your outlet box has ground wires, connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the post.
Your installation is now complete. Restore power to the junction box and test the fixture.
FAQ:
- Q: What should I do if I exceed the maximum wattage rating?
- A: It is important not to exceed the maximum wattage rating as it can lead to overheating and potential hazards. If you have exceeded the rating, promptly replace the bulbs with ones that comply with the fixture’s specifications.
- Q: How can I get assistance with parts or assembly?
- A : For any assistance with parts or assembly, please email customer service at info@aviancelighting.net
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the installation instructions do apply to this product.
HD00834
WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
ASSEMBLING THE FIXTURE (Fig.1)
- Shut off the power at the circuit breaker and remove old fixture, including the single bar.
- Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
- Put the candle sleeve(G) over the lamp holder.
- Install the light bulbs (not included) in accordance with the fixture’s specifications. NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
- Attach the pipe thread(C) into the shade of the lamp body(D), aligning the box top center screw hole with the pipe thread, by turning it clockwise until tight. Attach the cove (B) to the lamp body(D), then lock it securely with the loop(A).
- Attach the assembly lamp body onto the post (F, no included) and lock it securely with the screws (E).
CONNECTING THE WIRES (Fig.2)
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has a ground wires (green or bare copper) connect fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the post.
Your installation is now complete. Return power to the junction box and test the fixture.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:info@aviancelighting.net
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING, INC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>