PHILLIPS CONNECT 77-S108 Swing Door Sensor User Manual

: June 28, 2024
: PHILLIPS CONNECT

Table of Contents

PHILLIPS CONNECT 77-S108 Swing Door Sensor
Product Information
Product Usage Instructions
Frequently Asked Questions
INTRODUCTION
OPERATION SCENARIOS
HARDWARE FEATURES AND SPECIFICATIONS
MECHANICAL DETAILS
COMPANY INFORMATION
COPYRIGHT NOTICE
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
INDUSTRY CANADA STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILLIPS CONNECT 77-S108 Swing Door Sensor

PHILLIPS-CONNECT-77-S108-Swing-Door-Sensor-PRODUCT

Product Information

Specifications

Battery: Lithium, non-rechargeable
Nominal Capacity: 2.7 Ah
Maximum Voltage: 4.2 VDC
Gateway Data Interface: Bluetooth 4.2
Sensor Magnet Detection Range: Sensor surface to 1 (mounted on steel)
Sensor Dimensions: 4.3″ (H) x 2.2″ (W) x 1″ (D) (109.2 mm x 55.9 mm x 25.4 mm)
Magnet Dimensions: 2.4″ (H) x 2.4″ (W) x 1″ (D) (61.0 mm x 61.0 mm x 25.4 mm)
Sensor Weight: 0.16 lbs. (71.7 g)
Magnet Weight: 0.12 lbs. (56.2 g)
Certifications: FCC / IC

Product Usage Instructions

Installation

Follow these steps for a quick installation using the VHB Tape:

Clean the surface where you will be attaching the sensor.
Peel off the protective film from the VHB Tape on the sensor.
Press the sensor firmly onto the surface and hold for at least 30 seconds to ensure adhesion.

Swing Door Operation

For trailer swing doors:

The sensor detects the presence or absence of a magnetic field in close range.
Install either the sensor or magnet on the door and the other component on a door sill or a different door.

Roll Door Operation

For trailer roll doors:

The integrated accelerometer sensor determines the sensor orientation with respect to gravity.
Secure the sensor as close as possible to the top of the roll door.

Frequently Asked Questions

Q: How do I check the battery level of the sensor?

A: The battery level can be checked through the accompanying mobile app that connects to the sensor via Bluetooth.

Part #77-S108 – Swing Door Model
Part #77-S138 – Roll Door Model

INTRODUCTION

The Door√™ Sensor from Phillips Connect Technologies, in conjunction with a Phillips Connect Asset Tracking Telematics Gateway, comprise the main components of the Door√ Sensor System. The Door√ Sensor is typically affixed to the trailer door, either using the accompanying magnet on a swing door, or the beacon unit alone on a roll door. The Door√ Sensor is an IoT peripheral that detects whether a trailer door is in the open or closed position and transmits that status over BLE (Bluetooth Low Energy). The Door√ Sensor operates from a non-rechargeable lithium battery with enough capacity to last for the service life of the sensor.

Door√ Sensor features include:

2-minute Installation with VHB Tape
Bluetooth Low Energy (BLE) Beacon
IP67 Waterproof Standard

A typical application for the Door√ Sensor is illustrated below:

PHILLIPS-CONNECT-77-S108-Swing-Door-Sensor-FIG-1

OPERATION SCENARIOS

As stated, the Phillips Connect Door√ Sensor is designed to work with both trailer swing doors and trailer roll doors.

SWING DOOR OPERATION (77-S108)
For trailer swing doors, the sensor detects the presence or absence of a magnetic field in close range. In this configuration the door sensor operates with a second component, a magnet. The installation consists of either the sensor or magnet secured to a door. The other component is then installed on a door sill or a different door.

ROLL DOOR OPERATION (77-S138)
For trailer roll doors, the integrated accelerometer sensor is used to determine the sensor orientation with respect to gravity. The installation consists of just the sensor, which is secured as close as possible to the top of the roll door.

HARDWARE FEATURES AND SPECIFICATIONS

Supported features and specifications include the following:

ELECTRICAL / BATTERY
Battery Type: Lithium, non-rechargeable

Nominal Capacity: 2.7 Ah
Maximum Voltage: 4.2 VDC

GATEWAY DATA INTERFACE
Bluetooth 4.2

SENSOR PROPERTIES
Sensor Magnet Detection Range: Sensor surface to 1” (mounted on steel)

ENVIRONMENTAL
Ingress Protection Rating: IP67
Operating Temperature: -40°F to 149°F (-40°C to 65°C)
Storage Temperature: 32°F to 104°F (0°C to 40°C)

MECHANICAL
Sensor: 4.3” (H) x 2.2” (W) x 1” (D) (109.2 mm x 55.9 mm x 25.4 mm)
Magnet: 2.4” (H) x 2.4” (W) x 1” (D) (61.0 mm x 61.0 mm x 25.4 mm)
Weight (Sensor): 0.16 lbs. (71.7 g)
Weight (Magnet): 0.12 lbs. (56.2 g)

CERTIFICATIONS
FCC / IC

MECHANICAL DETAILS

77-S108 FRONT/SIDE VIEWS WITH DIMENSIONS

PHILLIPS-CONNECT-77-S108-Swing-Door-Sensor-FIG-2

COPYRIGHT NOTICE

© 2022 Phillips Connect Technologies LLC. All rights reserved.
Phillips Connect Technologies LLC reserves the right to modify the units, specification, or this document without prior notice in the interest of improving performance, reliability, or servicing. Reasonable efforts have been made to assure the accuracy of this document; however, Phillips Connect Technologies assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information herein. Product updates may result in differences between the information provided in this document and the product shipped. Please contact Phillips Connect Technologies LLC for access to the most current documentation.
No part of this document or information within this document may be copied, reproduced, distributed, merged, or modified without the express written consent of Phillips Connect Technologies LLC.

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment.
The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INDUSTRY CANADA STATEMENT

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). operation is subject to the following two conditions:

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

Door√™ User Manual