PHILLIPS CONNECT 77-S211 BLK Cargo Vision Sensor User Manual

: June 6, 2024
: PHILLIPS CONNECT

Table of Contents

INTRODUCTION
GENERAL SPECIFICATIONS
MECHANICAL DETAILS
- FRONT/REAR DIMENSIONS
- SIDE DIMENSIONS
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
INDUSTRY CANADA STATEMENT
COMPANY INFORMATION
Technical Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILLIPS CONNECT 77-S211 BLK Cargo Vision Sensor User Manual

INTRODUCTION

The Phillips Connect CargoVision is one of a growing family of sensors and system monitoring products from Phillips Connect used in conjunction with a PCT Gateway and Remote Listener System, or other cloud-based reporting system. CargoVision is designed to provide an uncompromising, on-demand view of the interior of a trailer in 1080P quality.

Simple installation and connectivity to your existing Phillips Connect Trailer Gateway module provides the ability to pre-program image capture events based on motion, door open/closed (if equipped), time-based or web-based image on- demand. Images are uploaded to the cloud for viewing through the Phillips Connect customer portal or automated API feed.

GENERAL SPECIFICATIONS

Environmental Resistance: IP67
Operational Temperature: -40C to 70C
Solar Panel Max Power: 2.7W
Battery Capacity: 5.3Ah
Installation Time: -15 minutes
Connectivity: BLE 2.4 GHz (to PCT Gateway module)
Image Quality: 1080P
Ideal Mounting Location: Top, Rear, Driver’s Side of trailer approximately 48″ from rear of trailer and 12″ from roof
Mounting Location Tolerance: +/-8″ from roof, +/- 24″ from rear door
Flash: High power dispersion lensed IR LED (x2)

Mounting Surface

Interior View (Mount)

MECHANICAL DETAILS

FRONT/REAR DIMENSIONS

SIDE DIMENSIONS

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: FCC Radiation Exposure Statement

This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INDUSTRY CANADA STATEMENT

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). operation is subject to the following two conditions:

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

This radio transmitter (ISED certification number: 25015-CCP01) has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.