PHILLIPS CONNECT S7PR1 Smart7 Pro Integrated Telematics Hub User Manual

: June 1, 2024
: PHILLIPS CONNECT

Table of Contents

INTRODUCTION
HARDWARE FEATURES
TECHNICAL SPECIFICATIONS
OPTIONAL BUILT-IN SENSORS
MECHANICAL DETAILS
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
INDUSTRY CANADA STATEMENT
COMPANY INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILLIPS CONNECT S7PR1 Smart7 Pro Integrated Telematics Hub User Manual

INTRODUCTION

The Smart 7 Pro™ 4G LTE Asset Tracking Gateway from Phillips Connect is a vehicle tracking device that combines GPS location with LTE and Bluetooth. Smart 7 Pro monitors vehicle and asset functions and collects data for tracking and analysis.

The Smart7 Pro Gateway appears to the user of a server application as a single endpoint device. It can be queried, updated, and configured either through a serial connection or an over-the air (OTA) LTE IP connection. Smart7 Pro presents itself over the connections as an enhanced cellular modem with attached functional elements. These elements include:

GPS location engine
General Purpose Bidirectional I/O (GPIO) pins
Relay drive pin output
CAN Communication
BLE 5.2 provides expandable sensor connectivity

The following is a typical application scenario:

HARDWARE FEATURES

The Smart 7 Pro Gateway ships from the factory pre-configured for a specific set of functions and can be configured and commissioned in the field, while providing support for external control through a Phillips Connect proprietary set of commands. Supported features include the following:

Solution Highlights

Manage and view your assets in the cloud-based Remote Listening System
Real-time visibility and simple geofencing
Automated alerts configurable in the Remote Listening System
Up to 6 months of reporting (on fully charged battery, stationary asset)
Flawless operation in the harshest temperatures
Configurable reporting when in motion
2 reports per day when parked (typical)

Powerful Cost Saving Tools

Optimize trailer pool management
Automate yard checks
Covert installations help eliminate trailer theft and cargo loss
Improve driver satisfaction
Manage detention billing

TECHNICAL SPECIFICATIONS

CELLULAR SUPPORT
LTE-FDD: Bands B2/B4/B12
WCDMA: Bands B2/B4/B5

GLOBAL NAVIGATION SATELLITE SYSTEM (GNSS)
Supported Satellite Systems: GPS; GLONASS; BeiDou (COMPASS); Galileo; QZSS
Accuracy: Circular error probability (CEP-50) with Open Sky, <2.5 meters
Additional Features: Assisted GPS; WAAS Support

SENSOR DATA INTERFACES
Bluetooth 5.2
TIA-485-A

Protocol: PCT BUS

CAN Bus 2.0B

SAE J 1939
ISO 14229

GPIO: 1 Channe

ELECTRICAL / POWER MANAGEMENT
Operating Voltage: 10 VDC – 32 VDC
Power supply to sensors: 12VDC / 500 mA
Peak current draw from tractor: 2 A @ 12 VDC

Battery charger draw: 1 A
Sensor draw: 500 mA
Telematics draw: 150 mA

Battery Type: Li-ion, rechargeable

Nominal Capacity: 10.6 Ah
Maximum Voltage: 4.2 VDC
Cell Cycle Life: ≥1000 cycles; ≥80% retention

Solar Panel IMP: 0.36 A
Power management modes: Normal (Full power), Listen, Stealth

ENVIRONMENTAL
Ingress Protection Ratings: IP67; IP69K
Operating Temperature: -40°F to 149°F (-40°C to 65°C)
Storage Temperature : -40°F to 113°F (-40°C to 45°C)
Battery Charging Temperature: -4°F to 131°F (-20°C to +55°C)
Operating Humidity: 20% to 90% (non-condensing)
Storage Humidity: 10% to 95% (non-condensing)

MECHANICAL
Dimensions: 13.6” (L) x 7.0” (W) x 4.1” (H) (345 mm x 178 mm x 104 mm)
Weight: 5.31 lbs. (2.40 kg)
Mounting: 6 x 5/16″ bolts

CERTIFICATIONS
FCC / IC
PTCRB Cellular

NTEGRATED: GATEWAY SENSORS

Orientation
Vibration
Temperature
Battery Voltage
Solar Panel Current
Primary Input Voltage
Secondary Input Voltage
GNSS Location
GNSS Odometer
Device Time via GNSS and NITZ

OPTIONAL BUILT-IN SENSORS

Light OutCheck™
Monitoring of all trailer lighting circuits during active use.
On-demand recheck of lighting circuits when tractor power is unavailable.

Maximum lamp circuit voltage 20 VDC
Integrated re settable 5 A fuses (10 A on red circuit)
Less than 100 mV insertion loss @ 5 A
Maximum amperage detection 2 A
PreCheck lighting circuits up to 1 A
Amperage resolution 2 mA

**ABS Fault CodeCheck™ ***
Retrieved ABS data includes:

Fault lamp status
DTC trouble-codes (active & stored)
ABS Odometer
VIN (if programmed into ABS)

*Compatible with most ABS manufacturers

PreCheck™
Schedule-based or remote on-demand

Lamp circuit supply : 11.5 VDC / 1 A
External sensor supply: 12 VDC / 500 mA

MECHANICAL DETAILS

Top/Side dimensions are provided in inches.

TOP DIMENSIONS

SIDE DIMENSIONS

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INDUSTRY CANADA STATEMENT

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). operation is subject to the following two conditions:

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body