PHILLIPS CONNECT 77-S230 SmartPair Beacon User Manual
- June 3, 2024
- PHILLIPS CONNECT
Table of Contents
PHILLIPS CONNECT 77-S230 SmartPair Beacon
INTRODUCTION
The SmartPair Beacon™ from Phillips Connect Technologies, in conjunction with a Phillips Asset Tracking Gateway, comprise the main components of the Tractor Trailer Pairing System. The SmartPair Beacon is typically affixed to the Tractor and is programmed with a unique Tractor ID number. Bluetooth advertisements from SmartPair Beacons are received and collected by the Phillips Gateway located on the Trailer, then parsed until it can be determined that one SmartPair Beacon has been successfully associated with one Gateway. Changes in pairing status are reported by the Gateway to a Remote Listener System, which collects data for tracking and analysis.
SmartPair Beacon features include:
- IP67 Waterproof Standard
- 2-minute Installation with VHB Tape
- Bluetooth Low Energy (BLE) Beacon
A typical application is illustrated in #19 below:
HARDWARE FEATURES AND SPECIFICATIONS
Supported features and specifications include the following:
BATTERY PACK AND LIFETIME 77-S230:\
- High-capacity lithium battery
- 5-year lifetime
- 5000 pairing events
BLUETOOTH WIRELESS INTERFACE
- Bluetooth LE 5.0 class II transmitter
- Public key 224-bit ECC encryption
ENVIRONMENTAL
- IP67 enclosure for electronics and battery
- Operating temp: -50C to 70C
- Recommended storage: 0C to 40C
PHYSICAL DIMENSIONS
- 77-S230: 4.3” height x 2.75” width x 1” depth
CERTIFICATIONS
- FCC / IC
- BBQ Bluetooth
MECHANICAL DETAILS
FRONT/SIDE/3D VIEWS WITH DIMENSIONS 
COMPANY INFORMATION
Phillips Connect Technologies LLC
5231 California Ave. Suite 110 Irvine, CA 92617
Technical Support 1-833-213-5839
Support@Phillips-Connect.com Sales
1-833-213-5839 PCT-Sales@Phillips-
Connect.com
COPYRIGHT NOTICE
© 2022 Phillips Connect Technologies LLC. All rights reserved.
Phillips Connect Technologies LLC reserves the right to modify the units,
specification, or this document without prior notice in the interest of
improving performance, reliability, or servicing. Reasonable efforts have been
made to assure the accuracy of this document; however, Phillips Connect
Technologies assumes no liability resulting from any inaccuracies or omissions
in this document, or from use of the information herein. Product updates may
result in differences between the information provided in this document and
the product shipped. Please contact Phillips Connect Technologies LLC for
access to the most current documentation. No part of this document or
information within this document may be copied, reproduced, distributed,
merged, or modified without the express written consent of Phillips Connect
Technologies LLC.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with the FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and your body. The
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
INDUSTRY CANADA STATEMENT
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). operation is subject to the following two conditions:
- This device may not cause interference
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement
This equipment complies with Canada’s radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>