concept VP4350 Cordless Hand-Held Vacuum Cleaner Instruction Manual

: June 24, 2024
: concept

Table of Contents

concept VP4350 Cordless Hand-Held Vacuum Cleaner
IMPORTANT SAFETY PRECAUTIONS
PRODUCT DESCRIPTION
ACCESSORIES
OPERATING INSTRUCTIONS
CLEANING AND MAINTENANCE
TROUBLESHOOTING
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

concept VP4350 Cordless Hand-Held Vacuum Cleaner

ACKNOWLEDGMENT
Thank you for purchasing a Concept product. We wish you much joy with your new appliance every day you use it.
Please read the instruction manual carefully before initial use. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance.

Technical specifications

| VP4350| VP4351| VP4352| VP4353| VP4354
Battery voltage| 7.4 V| 11.1 V| 14.8 V| 18.5 V| 22.2 V
| Input:| Input:| Input:| Input:| Input:
| 100-240 V~,| 100-240 V~,| 100-240 V~,| 100-240 V~,| 100-240 V~,
Charger voltage| 50/60 Hz, 0,4 A;| 50/60 Hz, 0,4 A;| 50/60 Hz, 0,4 A;| 50/60 Hz; 0,4 A;| 50/60 Hz; 0,4 A;
| Output: 9,6 V| Output: 14 V DC,| Output: 18 V DC,| Output: 22 V DC,| Output: 27 V DC,
| DC, 500 mA| 500 mA| 500 mA| 500 mA| 500 mA
Input| 50 W| 80 W| 100 W| 110 W| 150 W
Sound level| 68 dB| 70 dB| 72 dB| 74 dB| 76 dB
Full charging time| 4-5 hours| 4-5 hours| 4-5 hours| 4-5 hours| 4-5 hours
Operation time| approx. 20 min.| approx. 20 min.| approx. 20 min.| approx. 22 min.| approx. 22 min.

IMPORTANT SAFETY PRECAUTIONS

Do not use the appliance in any other way than as described in this manual.
Make sure the mains voltage and current protection correspond to the values on the rating plate of the charging station.
Do not leave the appliance without supervision when it is turned on.
When disconnecting the unit from the wall outlet, never pull the power cord, grasp the charger and disconnect it by removing it from the receptacle.
Do not allow children or unauthorized people to handle the appliance, use it out of their reach.
Pay extra attention if the appliance is used near children.
Do not use the appliance as a toy.
Do not use any accessories other than those recommended by the manufacturer.
Do not use a charger with a damaged cord or plug and have it repaired immediately by an authorized service centre.
Keep the appliance away from heat sources such as radiators, ovens, etc. Protect it from direct sunlight and humidity.
Do not touch the appliance with wet hands.
Do not insert any objects into the openings. Do not use the appliance if any of the openings is clogged.
Do not use the appliance with dirty filters.
Do not put the battery in fire or expose it to temperatures above 40 °C.
Do not touch the moving parts of the appliance during operation.
Do not repair the appliance yourself. Contact an authorized service centre.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Cleaning and maintenance performed by the user must not be carried out by children unless they are at least 8 years old and under supervision. Children aged under 8 years of age must be kept away from the appliance and its power cord. Do not let children play with the appliance.
Take extra caution when vacuuming on stairs.
If the appliance intake is clogged, switch off the appliance and remove the dirt before switching on again.
When attaching accessories during cleaning or in the event of a malfunction, switch off the appliance and disconnect the charger from wall socket.
The appliance is only suitable for home use and is not intended for commercial use.
Do not vacuum anything burning like cigarettes, matches or hot ash.
Do not use the appliance in rooms with increased air humidity, do not vacuum flammable liquids (such as petrol) and do not use the appliance in rooms where these substances may be present.
Never vacuum without vacuum cleaner filters. Every time you use the appliance, make sure the vacuum cleaner filters are properly installed.
Do not immerse the power cord or the charger in water or any other liquid.
Check the appliance and the charger cord for damage regularly. Never switch on a damaged appliance.
Before cleaning and after use of the appliance, switch off the appliance and allow it to cool down.
Before vacuuming, remove all large or sharp objects from the surface intended for vacuum cleaning, such objects may damage one of the vacuum cleaner filters.
Do not use the appliance with dirty filters.

Damages from failure to follow the manufacturer’s instructions are not covered by the warranty.

PRODUCT DESCRIPTION

Dust container
Filter
Dust container release button
Indicator light
On/Off switch
Dust container
External filter
HEPA filter

concept-VP4350-Cordless-Hand-Held-Vacuum-Cleaner-1

ACCESSORIES

A HEPA filter
B Head for vacuuming liquids
C Nozzle with a brush *for VP4352, VP4353, VP4354 only
D Slot nozzle
E Head reducer *for VP4351, VP4352, VP4353, VP4354 only
F Charging station *for VP4350, VP4351, VP4352 only
G PET brush *for VP4351, VP4353, VP4354 only
H Car nozzle *for VP4352, VP4353, VP4354 only
I Floor nozzle *for VP4353, VP4354 only
J Bag for accessories *for VP4353, VP4354 only
K Cleaning brush *for VP4353, VP4354 only
L Charger *for VP4353, VP4354 only
M Extension tube 2 pcs *for VP4353, VP4354 only

OPERATING INSTRUCTIONS

Assembling the vacuum cleaner
NOTICE Always switch off the appliance and disconnect the charger from wall socket before assembling or removing accessories! Accessories

Floor nozzle *for VP4353, VP4354 only
Slot nozzle
This nozzle is used for vacuuming spaces which are hard to reach, such as radiators, slots, corners, bases, space between the upholstery, etc.
Nozzle with a brush
This nozzle is used for vacuuming furniture, upholstery, books, lamps, etc. *for VP4352, VP4353, VP4354 only
PET brush
This brush is used for vacuuming animal fur directly on the animal (cat, dog). *for VP4351, VP4353 and VP4354 only
Car nozzle
This nozzle is used for vacuuming spaces in cars which are not easily accessed by vacuum cleaners. *for VP4352, VP4353, VP4354 only
Head for vacuuming water
This head is used for vacuuming a smaller amount of water.
Head reducer
It is used to attach the PET brush and Car nozzle to the vacuum cleaner. *for VP4351, VP4352, VP4353 and VP4354 only
Bag for accessories *for VP4353, VP4354 only
Cleaning brush for cleaning the HEPA filter *for VP4353, VP4354 only
Charger *for VP4353, VP4354 only
Charging station *for VP4350, VP4351 and VP4352 only
Extension tube 2 pcs *for VP4353, VP4354 only

Charging the battery
To prolong the life of the vacuum cleaner battery, follow these instructions:

Do not leave the vacuum cleaner fully charged or completely discharged for a long time.
Prolonged discharged of the battery will result in loss of its capacity.
Do not let the vacuum cleaner to be completely discharged.
It is ideal to keep the capacity of the battery between 20 % – 80 %.

During charging, three LED lights next to the power button flash one by one.
The charging is complete when all three LED lights are continuously on.
Operating time at full charge of the battery is approximately 20 minutes.

concept-VP4350-Cordless-Hand-Held-Vacuum-Cleaner-2

Using the vacuum cleaner
NOTE Before using the vacuum cleaner, make sure that the filters are correctly positioned and fixed.

Remove the vacuum cleaner from the charging base. *for VP4350, VP4351 and VP4352 only
Press the On/Off switch to turn on the vacuum cleaner.
After you are done using it, press the On/Off switch again to turn it off.

Checking the fullness of the dust container
If the suction power of the vacuum cleaner is reduced or the dust container is full, empty it and clean the vacuum cleaner filter. For the VP4353 and VP4354, you can use a cleaning brush (K) to clean the filters.

Vacuuming water
The vacuum cleaner also allows you to vacuum a small amount of water. It is necessary to attach the head for vacuuming liquids to the vacuum cleaner. However, the amount of water must not exceed the maximum level of dirt of the dust container. This may cause clogging of filters and serious damage to the appliance. Empty the dust container before vacuuming water. Never leave water in the container.

MAINTENANCE
It is recommended to empty the dust container and clean the vacuum cleaner filters after each use of the vacuum cleaner.

Emptying the dust container

Disconnect the charger from the mains.
Hold the vacuum cleaner down with a dust container.
Press the latch to release the dust container.
Remove the water separator and empty the vacuum cleaner dust container.
Reverse the procedure to attach the water separator and the filter and put the dust container back.

Cleaning and replacing the permanent filter
The vacuum cleaner filter can be cleaned by mechanical tapping and cleaning with a soft brush. Heavily soiled filter can be washed after this step and cleaned with a soft brush in lukewarm water without detergents.
It is important to let the wet parts dry thoroughly. A wet filter would be depleted by vacuuming! Do not use a hair dryer for drying!

Note : Wet cleaning can cause more wear on the filter and thereby shortening its life.

The filter should be cleaned or replaced with visible soiling or when the suction power of the vacuum cleaner drops.
Check it after each use of the vacuum cleaner.
To avoid damaging the vacuum cleaner, do not use it without a properly fitted filter and water separator.
You can purchase a suitable filter type from your dealer or order from the manufacturer.

CLEANING AND MAINTENANCE

Accessories and vacuum cleaner can be cleaned with a damp cloth.
Do not immerse the power cord or the charger in water or any other liquid.
Do not use aggressive substances such as solvents or abrasives for cleaning!

TROUBLESHOOTING

Problem	Cause	Remedy
The motor is not working.	The battery is discharged.	Charge

the battery.

Reduction of suction power.

| Full or clogged dust container.| Empty and clean the dust container.
The filter is clogged.| Clean or replace the filter.
Operating time at full charge is less than 1 minute.| The battery life is over.| Replace the battery with a new one. Contact an authorized service centre.
The vacuum cleaner is warming up.| Warming up of the vacuum cleaner during operation is normal, it is not a malfunction.

BATTERY DISPOSAL
The appliance contains a Ni-MH battery. This type of battery contains substances that can damage the environment in their disintegration. Before disposing of the appliance or replacing the battery, the original battery must be removed and returned to a suitable collection point.
To remove the battery, open the cover on the bottom of the vacuum cleaner.

SERVICE
Extensive maintenance or repair, which requires access to internal parts of the product, has to be performed by a qualified service centre.

ENVIRONMENTAL CONCERNS

Packaging materials and old appliances should be recycled.
Packaging materials may be disposed of as sorted waste.
Dispose the plastic bags made of polyethylene (PE) of as sorted waste.

Recycling of the appliance at the end of its lifespan
This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (Waste Electrical and Electronic Equipment – WEEE). The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead, it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The disposal of such material has to be done according to the recycling regulations. For more detailed information about recycling of this appliance see the authorized local office or service for household waste disposal or the shop, where you purchased the appliance.

The product meets all the necessary requirements of the EU directives applicable to the specific product.
Changes in text, design, and technical specifications are subject to change without notice and we reserve the right to change them.

Warranty

The manufacturer (or importer) is responsible for ensuring the product complies with the requirements of applicable legal regulations as well as those of the relevant technical standards. Moreover, they are responsible for ensuring the product has the properties the manufacturer described in documents related to the goods or those reasonably expected by the customer with regard to the nature of the goods or based on advertising produced by the manufacturer, and further they are responsible for ensuring the product is fit for the purpose proposed by the manufacturer or that a product of the same type is normally used for.

The quality warranty term is 24 months from product takeover by the customer.
The warranty does not apply to wear and tear caused by regular use. The customer shall not be entitled to any warranty claims if, prior to taking the product over, they knew the product contained a defect or if the defect is attributable to the customer.

The warranty specifically does not apply:

if the product installation, operation and service conditions stipulated in the product operating manual have not been adhered to,
to malfunctions caused due to mechanical, heat or chemical damage, short circuit, over voltage or incorrect installation,
to malfunctions caused by an inexpert third-party intervention,
to malfunctions caused by natural disaster,
to malfunctions caused by insufficient or inappropriate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,
to changes in colour of the heating surface or to scratching of the surface caused as a result of using the products in an unusual manner,
to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,
if the service life of certain product parts expires, e.g. for accumulators, bulbs, etc.

The warranty does not apply to any products and services provided along with the product (gifts, promotional articles, etc.).

Filing a complaint
A complaint against a product defect must be filed as soon as identified, yet no later than before the end of the warranty term.
The customer must file a product complaint with the dealer from which they have purchased the product, or with any authorised service centre, a list of which is included in the product package, or available at www. my-concept.com.
While filing a product complaint, the product must be duly cleaned and securely packed so as to prevent any damage during its transport to an authorised service centre, where relevant, unless the product is delivered in person.
The customer must submit proof of having concluded a purchase contract for the product by producing the receipt.
While filing their complaint, the customer must indicate the noted defect and identify the preferred complaint application method.

Complaints processing
As long as the noted defect may be removed, the user has the right to have the defect duly removed free of charge on a timely basis.
Where such a procedure is not reasonable with regard to the nature of the defect, the user may require to be supplied a new defect-free product (replacement), or, where the defect applies to a part of the product only, replacement of the part concerned. However, if replacement of the product or any part thereof is not proportionate with regard to the nature of the defect, especially if the defect can be removed without undue delay, the customer has the right to have the defect removed free of charge.

If the noted defect is not removable, or if the customer becomes entitled to replacement of the product or a part thereof, yet the replacement is not possible, for example due to the product having been sold out, the customer has the right to return the product (withdrawal from the contract).

The customer shall have the right to a new product (replacement) or to replacement of a part of the product even if the defect can be removed, provided they cannot properly use the product due to repeated occurrence of the defect or due to a high number of such defects. In such a case, the customer also has the right to return the product (by withdrawing from the contract).

If the product is not returned (the customer does not withdraw from the contract), or if the customer does not apply the right to a new defect-free product (replacement), to replacement of a part thereof or to repair of the product, they may request a reasonable discount. The customer also has a right to a reasonable discount if a new defect-free product cannot be supplied to them, or if a product part cannot be replaced or the product repaired unless the situation is remedied within a reasonable time limit, or if remedying the situation would create major discomfort on the part of the customer.

The seller, authorised service centre or a staff member authorised by them must decide about each complaint immediately or within three business days in complicated cases. This term does not include a reasonable period of time, depending on the type of product concerned, required for the defect to be assessed by an expert. A complaint, including defect removal, must be dealt with without any undue delay, yet no later than within 30 calendar days of the complaint filing date, unless the seller and the customer agree on a later deadline.

On returning the product (withdrawing from the contract) the customer must return any accessories and documents supplied along with the product.
The customer does not have the right to keep the defective parts and components of the product replaced as part of a repair of the product.
This shall be without prejudice to any other rights the customer may have in relation to the purchase of the product.
Remark : Complaints against products damaged in transport are governed by the carrier’s complaints procedure.

Manufacturer
Jindřich Valenta – Concept
Vysokomýtská 1800, 565 01 Choceň
Czech Republic
tel.: +420 465 471 400
fax +420 465 473 304
Company ID No. 13216660
email: servis@my-concept.cz
www: www.my-concept.com