TELTONIKA FMB930 Tracker Smart And Small User Guide

: June 24, 2024
: teltonika

Table of Contents

TELTONIKA FMB930 Tracker Smart And Small
Product Usage Instructions
KNOW YOUR DEVICE
PINOUT
SET UP YOUR DEVICE
PC CONNECTION (WINDOWS)
CONFIGURATION
DEFAULT CONFIGURATION SETTINGS
MOUNTING RECOMMENDATIONS
LED INDICATIONS
BASIC CHARACTERISTICS
FEATURES
SAFETY INFORMATION
CERTIFICATION AND APPROVALS
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TELTONIKA FMB930 Tracker Smart And Small

Specifications

Model: FMB930
Type: Small and smart tracker
Power Supply: +10-90 V DC
Micro-SIM Slot: Yes

Product Usage Instructions

Know Your Device

Top View: Power Cable
Bottom View (Without Cover): Navigate LED, Status Micro-USB LED, Battery Socket, Micro-SIM Slot

Pinout

PIN NUMBER	PIN NAME	DESCRIPTION
1	VCC (10-90) V DC (+)	Power supply (+10-90 V DC)
2	GND (-)	Ground

Wiring Scheme
Details on how to wire various components like ignition detection, alarm button, buzzer, etc. based on the provided diagram.

Set Up Your Device

Cover removal: Gently remove the cover using a plastic pry tool.
Micro-SIM card insert: Insert the Micro-SIM card with the cut-off corner pointing forward.
Battery connection: Connect the battery as shown on thedevice.
Attaching cover back: After configuration, reattach the device cover.

PC Connection (Windows)

Follow LED indications for proper connection.
Install USB drivers by downloading and running TeltonikaCOMDriver.exe.

Configuration
Change default factory settings via Teltonika Configurator software. Make sure to have the correct MS .NET Framework version installed.

FAQ

Q: How can I change the configuration settings of the FMB930 device?
A: The main configuration can be performed via Teltonika Configurator software available for Windows OS. Ensure to save changes to the device after modification.

FMB930\
Small and smart tracker

KNOW YOUR DEVICE

PINOUT

PIN NUMBER PIN NAME DESCRIPTION

	DC (+)	(+10-90 V DC)
2	GND (-)	(Black) Ground

3

|

DIN1

| (Yellow) Digital input,

channel 1. DEDICATED

| | FOR IGNITION INPUT

4

|

DOUT2

| (Grey) Digital output. Open collector output.
| | Max. 0,5 A DC

5

|

DOUT1

| (White) Digital output. Open collector output.
| | Max. 0,5 A DC

WIRING SCHEME

SET UP YOUR DEVICE

HOW TO INSERT MICRO-SIM CARD

COVER REMOVAL
Gently remove FMB930 cover using plastic pry tool from both sides.
MICRO-SIM CARD INSERT
Insert Micro-SIM card as shown with PIN request disabled or read our Wiki1 how to enter it later in Teltonika Configurator2. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
Connect the battery as
wiki.teltonika-gps.com/view/FMB930_Security_info
wiki.teltonika-gps.com/view/Teltonika_Configurator
BATTERY CONNECTION
shown on device. Position the battery in place where it does not obstruct other components.
ATTACHING COVER BACK
After configuration, see PC Connection (Windows)3, attach device cover back.

PC CONNECTION (WINDOWS)

Power-up FMB930 with DC voltage (10 – 90 V) power supply using power wires. LED’s should start blinking, see “LED indications1”.
Connect device to computer using Micro-USB cable or Bluetooth® connection:
- Using Micro-USB cable
- You will need to install USB drivers, see “How to install USB drivers (Windows)2”
- Using Bluetooth® wireless technology
- FMB930 Bluetooth® technology is enabled by default. Turn on Bluetooth® connection on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “FMB930_last_7_imei_digits”, without LE in the end.
- Enter default password 5555, press Connect and then select Done.
You are now ready to use the device on your computer.

Page 13, “LED indications”
Page 7, “How to install USB drivers (Windows)”

HOW TO INSTALL USB DRIVERS (WINDOWS)

Please download COM port drivers from here1.
Extract and run TeltonikaCOMDriver.exe.
Click Next in driver installation window.
In the following window click Install button.
Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION

At first FMB930 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET REQUIREMENTS

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking ? in the right bottom corner.

Configuration process begins by pressing on connected device.

After connection to Configurator Status window will be displayed.

Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMB930 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

Most important configurator section is GPRS – where all your server and GPRS settings6 can be configured and Data Acquisition7 – where data acquiring parameters can be configured. More details about FMB930 configuration using Configurator can be found in our Wiki8.

QUICK SMS CONFIGURATION
Default configuration has optimal parameters present to ensure best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it:

Note: Before SMS text, two space symbols should be inserted.

GPRS SETTINGS:

2001 – APN
2002 – APN username (if there are no APN username, empty field should be left)
2003 – APN password (if there are no APN password, empty field should be left)
SERVER SETTINGS:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)

DEFAULT CONFIGURATION SETTINGS

MOVEMENT AND IGNITION DETECTION:

DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:

DEVICE MAKES A RECORD ON STOP IF:

1 HOUR PASSES
while vehicle is stationary and ignition is off

RECORDS SENDING TO SERVER:

IF DEVICE HAS MADE A RECORD
it is sent to the server every 120 seconds

After successful SMS configuration, FMB930 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.

MOUNTING RECOMMENDATIONS

CONNECTING WIRES

Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
Wires cannot be connected to the board computers or control units.

CONNECTING POWER SOURCE

Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
When module is connected, measure voltage again to make sure it did not decrease.
It is recommended to connect to the main power cable in the fuse box.
Use 3A, 125V external fuse.

CONNECTING IGNITION WIRE

Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
Check if power is still available when you turn off any of vehicles devices.
Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.

CONNECTING GROUND WIRE

Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
For better contact scrub paint from the spot where loop is going to be connected.

LED INDICATIONS

NAVIGATION LED INDICATIONS

STATUS LED INDICATIONS

BASIC CHARACTERISTICS

POWER

BLUETOOTH® TECHNOLOGY

INTERFACE

PHYSICAL SPECIFICATION

OPERATING ENVIRONMENT

FEATURES

ELECTRICAL CHARACTERISTICS

SAFETY INFORMATION

This message contains information on how to operate FMB930 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+90 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
When connecting the connection (1×5) cables to the vehicle, the appropriate jumpers of the power supply of the vehicle should be disconnected.
Before dismounting the device from the vehicle, the 1×5 connection must be disconnected.
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard.
The device FMB930 is not designed as a navigational device for boats.

Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the powe supply..

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User‘s Manual before your start using the device. Full User‘s Manual version can be found in our Wiki1.
1 wiki.teltonika-gps.com/view/FMB930
Hereby, Teltonika declare under our sole responsibility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).
UK Conformity Assessed (UKCA) marking is a conformity mark that indicates conformity with the applicable requirements for above described products sold within Great Britain.
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
E-Mark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.
REACH addresses the production and use of chemical substances, and their potential impacts on both human health and the environment. Its 849 pages took seven years to pass, and it has been described as the most complex legislation in the Union’s history and the most important in 20 years. It is the strictest law to date regulating chemical substances and will affect industries throughout the world.
The standard aims to provide users more detailed information than vague marketing terms such as waterproof.
The RoHS1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use 10 different hazardous materials (to date).
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by UAB Teltonika Telematics is under license. Other trademarks and trade names are those of their respective owners.

DECLARATION OF IMEI ASSIGNMENT
The IMEI number is used by a GSM network to identify valid devices and therefore can be used for stopping a stolen phone from accessing that network. For example, if a mobile phone is stolen, the owner can call their network provider and instruct them to blacklist the phone using its IMEI number. This renders the phone useless on that network and sometimes other networks too, whether or not the phone’s subscriber identity module (SIM) is changed.

DECLARATION OF DEVICE OPERATION TEMPERATURE
An operating temperature is the temperature at which an electrical or mechanical device operates. The device will operate effectively within a specified temperature range which varies based on the device function and application context, and ranges from the minimum operating temperature to the maximum operating temperature (or peak operating temperature). Outside this range of safe operating temperatures the device may fail.

CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2.
wiki.teltonika-gps.com/view/FMB930Certification%26_Approvals

WARRANTY

We guarantee our products 24-month warranty1 period.
All batteries carry a 6-month warranty period.
Post-warranty repair service for products is not provided.
If a product stops operating within this specific warranty time, the product can be:

Repaired
Replaced with a new product
Replaced with an equivalent repaired product fulfilling the same functionality
Replaced with a different product fulfilling the same functionality in case of EOL for the original product

1 Additional agreement for an extended warranty period can be agreed upon separately.

WARRANTY DISCLAIMER

Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fault.
Products are intended to be used by personnel with training and experience.
Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance or inadequate installation – not following operating instructions (including failure to heed warnings) or use with equipment with which it is not intended to be used.
Warranty does not apply to any consequential damages.
Warranty is not applicable for supplementary product equipment (i. e. PSU, power cables, antennas) unless the accessory is defective on arrival.
More information on what is RMA1

1 wiki.teltonika-gps.com/view/RMA_guidelines
Quick Manual v1.6 // FMB930