V I V O MSAC1 Mini Split Air Conditioner Wall Mount Instruction Manual
- June 21, 2024
- V I V O
Table of Contents
- V I V O MSAC1 Mini Split Air Conditioner Wall Mount Instruction Manual
- CAUTION!
- WARNING: CHOKING HAZARD
- DO NOT EXCEED WEIGHT CAPACITY
- WARNING: DO NOT INSTALL INTO DRYWALL OR WOOD WALLS
- We’re Here for You
- Package Contents
- Included Hardware & Tools
- ASSEMBLY STEPS
- STEP 1
- STEP 2
- STEP 3
- STEP 4
- STEP 5
- STEP 6
- STEP 7
- STEP 8
- STEP 9
- STEP 10
- LAST UPDATED: 11/8/23 REV1 v1.0
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
V I V O MSAC1 Mini Split Air Conditioner Wall Mount Instruction Manual
CAUTION!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
WARNING: DO NOT INSTALL INTO DRYWALL OR WOOD WALLS
THIS MOUNT CAN ONLY BE INSTALLED INTO BRICK/CONCRETE WALLS AND IS NOT INTENDED FOR WOOD WALLS OR DRYWALL.
We’re Here for You
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
Package Contents
Included Hardware & Tools
ASSEMBLY STEPS
STEP 1
Fold down Inner Support from the inside of Support Bracket (B).
STEP 2
Lock Support Brackets (B) in the open position using M8x16mm Screws (S-B) and M8 Nuts (S-C). Tighten using Wrenches (T-A).
STEP 3
Install the Leveling Pads (D) into the back of Support Brackets (B). Levelig Pads are used to space the mini split unit unit mounting brackets off uneven mounting surfaces. They also provide additional leveling support once the AC unit is installed.
STEP 4
Measure the distance (1) between the Mounting Brackets on your mini split unit.
STEP 5
Slide Support Brackets (B) onto the sides of Crossbar (A).
STEP 6
Hold the mount assembly up to your desired mounting location with Support Brackets (B) spaced according to the measurement (1) taken in STEP 4.
Hold the mount assembly up to your desired mounting location with Support Brackets (B) spaced according to the measurement (1) taken in STEP 4.
Mark the center of either the top or bottom slot on both Support Bracket (B). The same location must be used on both Brackets.
STEP 7
Drill 3.7” (95mm) deep holes using a ½” (12mm) drill bit.
Secure Crossbar (A) and Support Brackets (B) to the wall using
ST8x90mm Screws (W-A) , M8 Washers (W-B) , and Concrete Anchors
(W-C). Tighten with a 17mm socket wrench.
STEP 8
Press Silicone Spacers (C) into the slots on Support Brackets (B) , ensuring they will align with the mounting bracket on your mini split unit when installed.
STEP 9
Place your mini split onto Support Brackets (B).
STEP 10
Secure the mini split to Support Brackets (B) using M8x30mm Screws
(S-A) , M8 Washers
(S-D) , and M8 Nuts (S-C). Tighten using Wrenches (T-A).
LAST UPDATED: 11/8/23 REV1 v1.0
Read More About This Manual & Download PDF:
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more