STRONG SRT 7805 Digital High Definition Satellite Receiver User Manual

: June 12, 2024
: STRONG

Table of Contents

STRONG SRT 7805 Digital High Definition Satellite Receiver
INTRODUCTION
YOUR RECEIVER
CONNECTIIONS
QUICK GUIDE TO USING YOUR RECEIVER
OPERATION
Multimedia
OTA SOFTWARE UPGRADE
TROUBLESHOOTING
SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

STRONG SRT 7805 Digital High Definition Satellite Receiver

$STRONG-SRT-7805-Digital-High-Definition-Satellite-Receiver-fig- $16$$

STRonG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EEC and 73/23EEC; RoHs 2002/95EEC
Manufactured under license from Dolby Laboratories Dolby’ and the ‘double-D’ symbol are trademarks of Dolby Laboratories Subject to alterations. In a consequence of continuous research and development technical specifications, design and appearance of products may change. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories, ASTRA is a registered trade mark of SES ASTRA, all other product names are trademarks or registered trademarks of their respective owners.
© STRONG 2010. All rights reserved. 07/2013

INTRODUCTION

Safety Instructions

DO NOT INSTALL YOUR RECEIVER:

In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.

DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:

To direct sunlight or any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.
Do not use a damaged power cord. It may cause a ﬁre or an electrical shock. Do not touch a power cord with wet hands. It may cause an electric shock.
When the receiver is not used for a long period of time, you should unplug the power cord from the wall socket.
Do not use alcohol or ammonia-based liquids to clean the receiver. If you wish, you may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap solution, only after disconnecting from the mains voltage supply. Make sure no foreign objects fall through the ventilation slots because this could cause ﬁre or an electric shock.
Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside.

Safety Precautions

Never open the receiver cover. It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards and your warranty will be void. Refer all maintenance or servicing to suitably qualiﬁed personnel.
When you are connecting cables, be sure that the receiver is disconnected from the mains supply voltage. Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment.
It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment. Please ensure that the electrical power supply corresponds with the voltage on the electrical identiﬁcation plate at the back of the receiver.

If the receiver does not operate normally, even after strictly following the instructions in this user manual, it is recommended to consult your local dealer or contact the appropriate service.

Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. For transporting the receiver from one place to another or if you are returning it under warranty conditions, make sure to repack the receiver in its original packaging with its accessories. Failing to comply with such packaging procedures could void your warranty.

Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below:

Refer to the user manual of your TV and your antenna.
Make sure that the SCART/HDMI cable and outdoor components are in a good condition and the SCART/HDMI connections are well shielded and from good quality.

This manual provides complete instructions for installing and using this receiver. The following symbols will serve as follow.

WARNING : Indicates warning information.
Note Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver. (BOLD CHARACTER)
Move to Represents a menu item within a window. (Italic Character)

Accessories

User’s Manual
1 Remote control unit
1 Main Power adapter with power cord
1 HD+ smart card
2x Batteries (AAA type)

WARNING:

The batteries should not be recharged, disassembled, electrically short- circuited, be mixed or used with other types of batteries.
If rechargeable accumulators instead of batteries are going to be used, we recommend using (e.g. NiMH) types with low self-discharge to ensure long time operation of remote control.

Usage of external USB devices $STRONG-SRT-7805-Digital-High-Definition- Satellite-Receiver-fig- $1$$

It is recommended to use USB 2.0 high speed storage devices. If your device is not compatible to USB 2.0 speciﬁcations, recording, playback and other multimedia functions of the receiver would not work properly. STRONG cannot guarantee the compatibility to all types of USB storage devices.
It is advised not to store important information on USB storage devices used with the receiver. Always make backups of data on your USB storage device before you are going to use it with your receiver.. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information.
Please ensure that either the USB device is already formatted to FAT or FAT32 system to use all media and record functions.
If your USB storage device is going to be used ONLY for record and playback, we recommend formatting it to E2FS (Linux ﬁle system) for the best performance of recording and playback. You can format the USB device via your receiver, refer to chapter 7.4.1 USB INFO & FORMAT for details.
Please be aware that formatting in Linux ﬁle system will have the consequence that Windows will not recognise this USB device anymore. If you want to use your E2FS formatted USB storage device under Windows we recommend you to use tools available in the WWW, for example the program: Ext2 Installable File System

General Information HD PLUS

Version of the Test Suite was used in conformance testing
Services via the Satellite Infrastructure are available in Germany (or such other territories as APS may deﬁne from time to time), only.
The usage of the HD+ card is designated for the Federal Republic of Germany only..

DOLBY
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

YOUR RECEIVER

DEFAULT PIN-CODE: 0000 $STRONG-SRT-7805-Digital-High-Definition-Satellite- Receiver-fig- $3$$
Front Panel

standby/on switch Turns the receiver ON or to Standby
navigations buttons Menu navigation
4 digit lED display Displays channel number or time
MEnU Opens the OSD menu
EXIT Exit from menu
oK Confirm selection
Card reader Slot to insert HD+ card for access of HD+ channels*

Rear Panel

sAT In To connect to the LNB of your satellite dish for reception of satellite broadcast signal
CoMPonEnT To connect to TV or Beemer for high video quality over Y/Pb/Pr component output
vIDEo (RCA) To connect to the RCA video input of your TV or VCR using an RCA cable
AUDIo (l/R) To connect to the audio input of TV, VCR or your HIFI using an RCA cable
Tv sCART To connect to TV using a SCART cable
HDMI To connect to the HDMI input of your TV using a good quality HDMI cable.
s/PDIf (Opt.) To connect to a digital or home cinema audio amplifier using an optical cable
Usb Connect your USB storage device (stick, HDD, etc.) to this port
DC PoWER To connect to the original included main power adapter (Input 110 – 240 V 50 ~ 60 Hz/ Output 12 V DC) there and connect main power adapter to the original included power cord.

Remote Control Unit $STRONG-SRT-7805-Digital-High-Definition-Satellite- Receiver-fig- $2$$

Turns the receiver ON/Standby
Mutes the audio output of the receiver
0~9 Channel number and numeric value input
fAv Opens the favourite group selection
oPT Opens the audio and subtitle selection menu
TXT Displays the current Teletext of this channel, if available
f.lIsT Opens the playback list in viewing mode
MEDIA Opens the Multimedia menu in viewing mode
RECAll Toggles between the two last watched channels
GUIDE Displays the EPG (Electronic Program Guide)
vol Increasing/decreasing of the volume level
PAGE CH Switches to next/previous channel in viewing mode or scrolls page wise in lists
Info Press once to display channel information. Press twice to call extended program info.
RED For Teletext function, in OSD for specific functions
GREEn For Teletext function, in OSD for specific functions.
YElloW For Teletext function, in OSD for specific functions.
blUE In viewing mode opens the EPG overview, for Teletext and in OSD for specific functions
Scrolls channel and EPG information up/down in viewing mode, in OSD for navigation.
In OSD for navigation
oK In viewing mode displays the channel list, in Menu mode activation/ confirmation of the specific item
MEnU Opens the menu in viewing mode, within menu you can directly exit to viewing mode
EXIT In viewing mode removes appearing messages /Info banner, in OSD one step back or cancel actions
Tv/RAD Toggles between TV and Radio mode
AsPECT Show information about the screen format in broadcast.
HIsToRY Displays the last watched channels list in viewing mode including EPG information
sIGnAl Display signal and quality of satellite signal from current selected satellite and channel
Fast rewind
PLAY / Opens the playback list in viewing mode
Stop
Fast forward
In viewing mode starts Timeshift, in Multimedia for Pause function
Starts recording of the actual broadcast
f1~f4 No function

CONNECTIIONS

basic connection using a scart cable

Connect the LNB of your satellite dish to the SAT IN connector of your receiver using a good quality coax cable and suitable ‘F-connector’ plugs.
Connect one end of a good quality Scart cable to the TV SCART connector on your receiver and the other end to the SCART input of your TV.
Plug the power adapter & cord to a suitable wall outlet.

basic connection using an HDMI cable Fig. 5. $STRONG-SRT-7805-Digital-High- Definition-Satellite-Receiver-fig- $4$$

Connect the LNB of your satellite dish to the SAT IN connector of your receiver using a good quality coax cable and suitable ‘F-connector’ plugs.
Connect one end of a good quality HDMI cable to the HDMI output on your receiver and the other end to the HDMI input of your TV.
Plug the power adapter & cord to a suitable wall outlet.

Connecting multiple fixed dishes using a DisEqC 1.0 switch Fig. 6.

Connect the LNB’s of your fixed dishes to the inputs of a DiSEqC 1.0 switch
Connect the output or “to receiver” connector of the DiSEqC 1.0 switch to the SAT IN connector on your receiver.
Refer to section 3.1 or 3.2 for TV and mains connections

STARTING UP FOR THE FIRST TIME

Ensure that your satellite signal is of good quality and that all connections are sound. In case of difficulties or questions, please ask you local dealer for assistance. It is recommended to follow the Setup Wizard step by step. It will guide you through the basic installation and channel searching process. You can enjoy digital HD broadcasts within just a few minutes.

language selection

After turning on the power for the first time, the language selection menu will appear. Choose your language with and confirm with oK. In this welcome screen will the most important button description, be displayed. Once you are ready, press oK to advance to the next step of the Installation wizard. During any stage of the Setup Wizard, you can press EXIT to get back to the previous screen.

location selection

Here you can set the Time zone and switch the Summer time OFF or ON. Use to move the highlight and to change settings. Press oK to confirm and to continue.

output selection

Here you can select the connection type you use to your TV screen. Select HDMI / YUV if you use a HDMI or a component cable to HD TV screen. Select SCART if you’re using a Scart cable to “normally” TV screen. If SCART is selected, then select as well they correct size of you TV screen. Use to move the highlight and to change settings. Press oK to confirm and to continue.. note: HD+ services / channels can only be seen if correct selection is made

Channel installation

This receiver is equipped with a new fast channel installation system by Astra 19.2 satellite called APS. Per default all settings are correctly adjusted for a fast installation on Astra 19.2. Before you press OK button to start the scan process, ﬁrst check the Strength and Quality bars on the bottom of this menu. Green bars indicate a good signal and you can proceed. Yellow bars indicate that the signal condition is nearly acceptable and Red indicates bad signal. Adjust your dish for maximum possible signal strength and quality. Once the signal cannot be improved anymore, ﬁx the dish on this position and press OK to continue and start APS scan process. Once receiver ﬁnished this scan process a selection will popup with View or Next. Select View and press OK to enjoy and watch the digital satellite channels directly. Select Next if you want to scan for more satellites/channels. Refer to chapter 7.1.1 CHANNEL SCAN for detailed description.

Note: If you don’t want to use this option you can press the BLUE button to start a normal auto scan on the selected satellite.

First activation of your HD+ smart card

Your receiver is already delivered with correct inserted smart card. Although we recommend you to check that your smart card didn’t get loose during the transport.
If you have ensured that the SC is inserted properly, then you are ready for watching HD+ channels. Your SC is already activated, so you only need to switch to an HD+ service channel (please see separate HD+ sheet for HD+ channels reference).
If you have already switched to one of the desired programs, after 10 sec. you will have access to the HD+ service.
Now you are ready to enjoy the HD+ channels.

QUICK GUIDE TO USING YOUR RECEIVER

We at STRONG understand that you can’t wait to enjoy your new HD+ receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your STRONG HD+ receiver.
To turn your receiver ON or to Standby, use the STBY button on the remote control or the button on the left side of the front panel.
If you are using the HDMI connection for your TV set, it might be possible that you need to switch on TV and select the correct HDMI input ﬁrst.
Choose the desired channel with the buttons and OK or the CH+/CH- buttons. Alternatively, you can digit the channel number with the 0~9 buttons on the remote control. Or press OK in viewing mode to display the channel list.
The volume can be adjusted with the VOL+/VOL- buttons.

OPERATION

In viewing mode, several features are available to make watching TV a true pleasure. This paragraph describes these features. Please also read chapter 7.0 to get familiar with the menu of your new receiver.

Changing channels

Your new receiver is equipped with four ways to change channels.

via direct access
via the CH+/CH- buttons.
via the channel list
via selection of channel groups (APS)

Direct access
To gain direct access to a certain channel, simply input its number with the 0~9 buttons on the remote control. Channel numbers can be up to four digits long. Entering a number with less than four digits is possible. Just wait a few seconds and your receiver will switch to the selected channel.

Using the CH+/CH- buttons

CH+ or and OK will switch to a higher channel.
CH- or and OK will switch a lower channel.

Channel list

Press OK in viewing mode to display the Channel List. Use in the Channel List to highlight your channel of choice and press OK once to select the highlighted channel. Press OK again to leave the Channel List. The Channel List is equipped with a ﬁlter function to make ﬁnding your favourite channels easier. Within the Channel List, press button to jump to selections on left side of channel list banner. Here you can select following options: ALL, FAV, A~Z, SAT and APS.
Use to select one of these options and press button to select the list of your choice and OK
to conﬁrm.
You can use the TV/R button within the channel list to toggle between TV and radio channel list/s.

APS Channel list

Your receiver is equipped with new system called “APS” Astra Platform Service which store channels in separated channel lists on sort, type or group. If you are using the Astra 19.2 satellite and did scan on HD+ channel scan in installation, then this system is contained in the channel list.
Press OK in viewing mode to display the Channel List. Press button to select the group of your choice on the left side of the channel list banner. Select APS with the buttons and press the button
to show the group lists from APS channel system. Select your wanted channel group by buttons. Directly on the right side is displayed which channels belong to this selected group. Press button to enter this channel group and select it with the buttons. Press OK once to select the highlighted channel, by another pressing you can switch to viewing mode. The receiver will stay in the selected channel group until you will select another one.

Info Banner

At any time during viewing mode you can press the INFO button to get info about the current channel and program*. Press INFO twice to see program details about the current channel.

Note: Program information is only displayed when available. Availability depends on the broadcaster.

Audio language and Audio mode

Press OPT button in viewing mode to display this (Optional Settings) menu
In this menu you can select the Audio language and Audio Mode.
In the audio language selection you can select another language or Dolby digital if the selected channel supports this option.
Selection of Audio mode allows you to select between Stereo, Left or Right audio channel. In case the channels does not support, there will be no change to hear.

Teletext and Subtitles

Your receiver includes a fully featured Teletext. To access Teletext, press the TXT button in viewing mode. Then the menu to select Teletext & Subtitle Option will be displayed, when you press it for the 1st time. Use the buttons to select an option and use to change the setting. In case of DVB subtitles availability you can select them to be displayed and press OK there to conﬁrm. If only one Teletext language is available the receiver will show the abbreviation of the used one and you can’t select this item. Please choose “Goto Teletext” to display the Teletext on screen, then you can use the 0~9 buttons to input the number of the page you wish to see. The coloured buttons of the remote control allow you to display selected pages directly, as indicated on the bottom of the Teletext screen. Press EXIT to go back to viewing mode.

Note:
VBI Teletext on your TV set is not supported. Please use the Teletext of the receiver. If you are connected via HDMI, it could be the case that you will observe
that the TV set is switching resolution in case there are different resolutions broadcasted on the channels. This is no abnormality as this is a required behaviour followed on the speciﬁcations of this product.

HDMI video format
If you are connected via HDMI, it could be the case that you will observe that the TV set is switching resolution in case there are different resolutions broadcasted on the channels. This is no abnormality as this is a required behaviour followed on the speciﬁcations of this product.

EPG (Electronic Programme Guide)

The Electronic Programme Guide is a very useful function that allows you to watch programme schedules and information on screen and to select programs for recording. Press the GUIDE button to open the EPG overview. Use to select the desired channel and to move within the program schedules. If the desired event is selected, press INFO to open the detailed information. Use button to scroll, in case there is more than one page of information. Press INFO or RED to go back to the EPG overview. Within the EPG you can also set a Timer for the selected event, by pressing OK. Then you can choose if you want to Set a Reminder for Timer, Tune CH or Record, always including event/ channel information according to selected channel.
RED button allows you to Filter by Title, Channel or Theme. Here press GREEN to get back to EPG overview. YELLOW button allows you to select by date. Here press GREEN to get back to today’s EPG overview. Use the BLUE button to open the Weekly Overview for the selected channel, press BLUE again to get back to EPG overview.

Note:

Availability of EPG data depends on the broadcaster and selected transponder frequency.

Recording

Your receiver allows you to make an instant recording of the program you are watching, to an external USB HDD.
Simply press to start the recording. Press INFO button during a recording to see channel and record time information.
To stop the recording, press button and select OK and conﬁrm with OK button.
The maximum record time of each event is 2 hours.

Note : Please connect an USB storage device with sufﬁcient free space before you start a recording.

For recording HD broadcast, a high speed device is highly recommended.
On the HD+ channels it can happen that some events are protected and a recording is not possible or limited in speciﬁc concerns.

Time shift

The Time shift function allows you to pause live broadcast up to 90 minutes and resume normal watching without missing anything.
Press 2 to freeze the current broadcast. Press again to start time shifted playback. To stop Timeshift, press .
During the Time shift press EXIT to remove time shift banner and press u (PLAY) to recall the time shift banner. During time shift you can press or buttons to jump within time shift ﬁle. Press more times on these buttons to change the speed. You can choose between 2x, 4x, 8x, 16x and 32x.
On the HD+ channels it can happen that some events are protected and fast forward/ rewind in time shift is not possible or limited in speciﬁc concerns.

Note:

Time shift is only working correctly when a fast USB storage device such as an USB2.0 HDD / USB storage device is connected to the receiver. Further we recommend you to format the USB storage device to E2FS format for the proper function of record, playback and Time shift, please see special conditions in chapter 1.5 USAGE OF EXTERNAL USB DEVICES. Distorted picture and / or audio during Time shift indicate a low USB device speed. STRONG cannot guarantee for USB devices used. Especially when Timeshift is activated at channels with high data rate (High quality SD/HD), STRONG cannot guarantee an accurate Playback of the Time shifted ﬁle.

Playback of recording

After you have already made some recordings with this receiver you can simply play them back. Press F.LIST or (PLAY) button to open the Playback List. Use to select a record you want to playback and press OK to start. With the RED button you can delete ﬁles if you want to make some free space on your USB device. The recording will be stored with the current event name. You can rename the recording by pressing the GREEN button. With the YELLOW button you can protect a recording with the PIN Code, before it can be played back or deleted.

MENU

All important settings and features of your receiver can be operated from the Menu. It consists of the following sub-menus: Channel Setup, Control Panel, CAS, Multimedia and Program Guide. Press MENU in viewing mode to display the Menu.
Use to select a sub-menu and to choose an option. Press OK to advance to the chosen submenu. Press EXIT to go one step back or press MENU to go to viewing mode.

Channel Setup

The installation menu allows you to change satellite settings and to search for channels. It consists of the following sub-menus: Channel Scan and Channel Editor. Choose the desired sub menu with and press OK to advance.

Channel Scan

Use this menu to select the satellite, change the settings for the used antenna and start scan process for searching the channels.

Satellite: Use to highlight Satellite and to select the satellite you wish to change the settings for. To display the list of all available satellites, press oK. At the end of this list you can find Newsat1 -10. Those can be used to configure a new satellite setup.
LNB: Select LNB type if you are using another LNB as Univ.LNB model. As this is the common used LNB, it is set per default.
DiSEqC: If you are using a DiSEqC switch in order to connect more dishes, select the correct used switch type. Select DiSEqC 1.0 for maximum 4 dishes. DiSEqC 1.1 for maximum 16 dishes and select None if you don’t use any switch.
DiSEqC Port: If you are using a DiSEqC switch you need to set the correct DiSEqC port which belongs to the connected satellite.
Transponder: Select this option, if you want to scan manually or check the signal on the desired transponder frequency. Use to select the transponder of you choice, or open the Transponder list of the selected satellite with oK.
Motor Control: If you are using a DiSEqC motor to install multiple satellites. Select the according setup type with Select DiSEqC 1.2 for manual setup of each satellite or select GoTo-X for automatic calculation after you have adjusted the 0-position and corresponding Cartesian coordinates of your location.
Note : Please consider that GoTo X must be supported from your Motor as well!
Motor Setting: Here you can setup the necessary settings according to the used Motor Control. Adjust and store these settings correctly, in order to be able to proceed with Search Start

Search Start:

Before you start the scan process please make sure that all settings are made correctly and Strength and
Quality bars are showing green colours. If the Strength and Quality bars showing red or yellow colours, then the satellite signal is too weak. Please try to adjust your satellite dish first, to improve the signal.
At the first time installation there was performed the HD+ Channel Scan from APS. After this successful scan process you can choose following of the additional possibilities:
Select Search Start and press oK.

A new menu will be opened on the right side of your screen, called “Options”. Use this menu to perform an Automatic, TP (manual) or Network channel search on one or more satellites. Use to highlight and oK to select an option.

Start Auto Scan: Use this option to perform a full channel scan on the selected satellite, under the below mentioned conditions.
TP Search Start: Use this option to perform a scan on the selected transponder only.
Network Search Start: Use this option to receive new launched channels from the selected satellite.
The receiver will perform an additional search for channels from the NIT table (NIT= Network Identification Table).
Search Mode: Select All to scan all channels including scrambled channels or FTA to scan for Free-To-Air channels only.
NIT Search: Select OFF if you don’t want to perform a network search or set ON to perform a network search
DiSEqC repeat: Here you can set 1 x or 2 x time/s of DiSEqC repeat, if you are using a multiple switch system or a DiSEqC motor behind a DiSEqC switch.

After you have set all necessary settings, press oK to start the desired scan process. After the selected scan finished successfully the receiver will ask you to Save or Cancel, to save the search result select Save, to discard select Cancel

Channel Editor

Here you can Delete, Set Favourites, Lock, Move and Sort your channels.
Press Tv/RAD button on your remote to select TV or Radio channel list.
Use to highlight and oK to select channel(s) for the desired option explained below:
Press RED button to delete the selected channel/s or channel group/s.
Press GREEn to add or remove channels to/ from your favourite group.
Press YElloW to lock channel/s with a PIN code before you can watch or deleted it/them.
Press blUE to move channels within the selected channel list.
Press EXIT to exit this menu and select oK at the displayed message to store changes or choose Cancel to discard the changes.

Control Panel
The Control Panel allows you to change system settings as language and time, set protections with PIN code and reset the receiver back to the factory settings. It consists of the following sub-menus: System Setup, Factory Default and Lock Setup. Choose the desired sub menu with and press oK to advance.

system setup
Use the Setup menu to configure the system settings of your receiver. The following sub-menus are available: Language Setup, Time Setup, Receiver Information and User Setup.

language setup:

Here you can set the preferred OSD, Audio and Subtitle languages settings. Use to highlight the setting you wish to change and to change the value of the setting. Press oK to display a list of all available options, for the chosen setting. Press EXIT to exit and save settings.
OSD Language: This setting affects the menu language of your receiver. All menu’s and messages will be displayed in this language.
Audio: is the preferred audio language. The receiver will automatically switch audio to the preferred language whenever available.
Subtitle: Subtitles will be displayed in the selected language, whenever available

Time setup:

The Time Setup allows you to set the way the receiver collects and adjusts the time. You can also adjust the Auto Standby function here for an automatic switch to standby after a desired time, to save power. Use to highlight the setting you wish to change and or 0~9 to change the value of the highlighted setting. Press oK to display a list of all available options, for the chosen setting.
Local Time: Adjust the correct time zone you are located based on GMT.
Summer Time: Select OFF or ON to adjust the current setting for summer time.
Date: The date is normally synchronized by satellite signal. If you like to change another date, press oK to call calendar and use tu to change date.
Current Time: The time is normally synchronized by satellite signal. We recommend you not to change time manually, although you can enter another time. Use 0~9 numeric buttons to enter your time.
Auto Standby: This is a new, power saving feature that helps you in reducing power consumption. It will switch the receiver to standby mode when no command is given for the set time. Possible settings are: 1, 2, 3, 6, 12, 24 hours and OFF.
Once all settings are made, press EXIT to leave the menu. A confirmation banner will be shown to save your settings.

Receiver Information:

This menu contains valuable information about the model number, the software version and our web address www.strong.tv. A customer support agent might ask for the information given in this screen. Press EXIT to leave this menu.

User setup:

Within the User Setup menu you can configure the audio and video outputs of your receiver. Use pq to highlight the setting you wish to change and tu to change the value of the highlighted setting. Press oK to display a list of all available options, for the chosen setting

Video Output Via: Use this option to configure your connection to the TV set. Select SCART if you are connected by Scart cable or select HDMI/YUV if you are connected by HDMI or Component cable to TV set. Be aware that HD+ services / channels can only be seen if correct selection is made!
Resolution: If you have selected HDMI/YUV in above, then you can select the resolution of HDMI output. Available options are: 1080i, 720p, 576p and 576i.
Aspect Ratio: If you have selected SCART in above, then you can select the according aspect ratio of your TV set. Available options are: 4:3 and 16:9.
Display16:9 Event: Use this option to set the preferred way of conversion from 16:9 broadcasts in 4:3 TV set. You can choose between the following options: Letter-box (the full 16:9 picture will be displayed on your 4:3 TV set with black bars above and below the picture.), Pan and scan (The centre of the 16:9 picture will be displayed as full-screen on your 4:3 TV set) and Just Scale (Combination of Letter-box and Pan and scan.)
SCART Mode: Select RGB for the best picture quality or CVBS in case your TV doesn’t support RGB. In case you have set HDMI/YUV in the above setting, your Scart output will be switched to CVBS automatically.
Info banner Timeout: Defines the time after which the OSD banners time out. Possible settings are: 2~12 seconds.
TV List Timeout: Defines the time after which the TV list time out. Possible settings are: 2~12 seconds.
Dolby Digital Option: Select ON if you using an optical connection to you digital amplifier to enjoy Dolby Digital*, in case the selected channel support this. Select OFF if you not use this option.
Subtitle Control: Use this option to set the preferred way of subtitles support. Select Auto to switch subtitles automatically on if they are available, or select Manual to select ON or OFF. In viewing mode you can press the oPT button to enter this setting.

Advanced setup

In the User Setup menu, you can press the blue button to enter the advanced settings. It is strictly recommended not to change any of these settings unless you are absolutely sure and an advanced user.

LNB Power: Allows you to switch OFF or ON power of LNB.
DiSEqC repeat: Repeat command for commit switches (1, 2 and OFF)
Power save Mode: This setting will set the receiver in low power mode during standby in order to reduce standby power below 2 watt. If you select this option to ON be aware that wakeup of your receiver will take more then one minute.
Pre-Wakeup (min.): Here you can set the pre-wake-up time for your receiver if a Timer/recording is configured and you are using the Power save Mode during Standby (3, 4 and 5 min.).
HDCP Setting: To switch ON or OFF the control key for HD screens. If you select OFF will only low video resolution available.
Press oK to confirm and to exit this menu.

Factory Default:

A factory default will reset all settings of the receiver to the factory default. To reset the receiver, you have to enter your PIN code (DEfAUlT PIn: 0000) Select Factory Initialization and Press oK. You have to enter your PIN code again to make 100% sure that you want to perform this action.
After the reset, the receiver will start up with the Setup Wizard.

WARNING A factory reset will permanently delete all your personal settings, timers and stored channels. Please consider this before you perform a factory reset

Lock Setup:

Within the Lock Setup menu you can enable or disable the menu lock function and change the PIN code.
Before you can enter this menu you have to enter your PIN code (DEfAUlT PIn: 0000). Use to highlight the setting you wish to change and or 0~9 to change the value of the highlighted setting.
Install Lock: Here you can change the PIN code setting for the access to installation menu.
Select ON if you like to protect entering Control panel menu with PIN code.
Select OFF to disable this function.
Parental Lock: Select ON if you want to switch on the protection of channels with LOCK sign.
Select OFF to disable this function.
New PIN code: Use this function to set your own personal PIN code. Enter here your new PIN.
Confirm PIN code: Enter here again the new PIN code to confirm. A successful change of PIN is confirmed by an on screen message.
Use EXIT to go back to the previous menu.

SMART CARD

In this Nagra CAS menu you can read the details form your HD+ smart card and can change the PIN code from this Smart card.
Find below Smart Card Information all details as Subscribed date and Smart Card serial number. This information show you if card is still active and if you need to call the Call centre of HD+ to activated it again.
Press oK to open Change CA PIN menu. Enter with the numeric buttons 0~9 first default PIN code (0000) of 4 digits. Enter now your new PIN and confirm again PIN. A successful change of PIN is confirmed by an on screen message.
Use EXIT to go back to the previous menu.
WARING Please be aware, that the CA PIN is the PIN from your Smart Card, changing it has nothing to do with receiver PIN code!

Multimedia

The Multimedia menu allows you to see detail information of your connected USB device, handle your records and give you access to your music and pictures on USB device. It consists of the following submenus: USB info & Format, Record Manager and Music & Photo Player. Choose the desired sub menu with and press oK to advance.

Usb Info & format:

The USB Info & Format menu displays all details from the connected USB storage device. It contains information about the storage capacity and about the current free space for new recordings.
If you want that all functions are fully supported, as Jpeg and MP3 play back, ensure that either the USB device is already formatted in FAT or FAT32 system on your computer. When you are going to use it only for record and playback, we recommend you to format it to E2FS (Linux file system) in this menu for the best performance of record and playback.
Use to select HDD Format (E2FS) and press oK button to start formatting of the connected USB device.

To safely remove the external USB storage device press the GREEn button. Use EXIT to go back to the previous menu WARnInG The Format function will delete all records, data and information from your USB device. STRONG will not take any responsibility for damaged or lost data on the USB device. Please make a backup copy of important data on your USB device before you are going to use it with your receiver. Please be aware that formatting in Linux file system will have the consequence that Windows will not recognise such an USB device anymore. If you want to use your E2FS formatted USB storage device under Windows we recommend you to use tools available in the WWW, for example the program: Ext2 Installable File System.

Record Manager

The Record Manager can be used for the playback of previously recorded programs, to delete, rename and lock them.
Use to select a file in this folder. Press oK to start the playback of the desired recording. Press INFO during playback to see details form this record. If you have already watched this recording, then there will be a message displayed to ask you if you want to start the playback from the beginning, or if you want to start from the point you stopped watching before.
WARNING HD+ channel recordings are limited in playback concerns. If this limit has passed an HD+ message appears on your screen. Then this file can not be watched anymore and you can delete it to get free space for new recordings.
Your smart card must be valid to watch HD+ recordings, otherwise it will fail.

Press the RED button to delete a selected recording from your USB device.
Press the GREEn button to rename the recording.
Press the YElloW button to lock the recording with the PIN code. Afterwards you will need to enter this
PIN code to watch or delete the recording.

Music & Photo Player

In the Music & Photo Player menu you can navigate on your USB device to choose JPEG photos or MP3 music files.
Use to select a file or a folder. Press oK to mark a selected MP3 or JPEG and press to start playback/ show this file.
Press the RED button to select all MP 3 and JPEG in the folder or route. Use and press oK to select / unselect single files.
Press the GREEn button to add selected or all files into the My Media list.
Press the YElloW button to set Slide show or set MP3 repeat, depending on what you want to watch or hear.
Press the blUE button to start play back from My Media list.
During playback, the following functions are available:
starts playback of the next MP3 / Jpeg.
starts playback of the previous MP3 / Jpeg.
Press to pause the playback. Press again to resume playback.
stops playback.
starts playback of the next Jpeg.
starts playback of the previous Jpeg.
Press EXIT or to get back to the menu.

Note : STRONG can not guarantee play back of every JPEG format size or MP3 sample rate.

Program Guide
The Program Guide menu allows you access (EPG) Electronic Programme Guide and to set Timers for wakeup and/or recording.
Choose the desired sub menu with and press oK to advance.

EPG
The Electronic Programme Guide is a very useful function that allows you to watch programme schedules and information on screen and to mark programs for recording. Find all detailed descriptions in chapter

EPG
note: Availability of EPG data depends on the broadcaster.

Timers

Timers can be used to schedule recordings or to switch to a certain channel at a desired moment. It will help you not to miss your favourite events. You can set up to 30 Timers.
Use to select one of the available timers. Press oK to advance. The Edit Timer screen will now be displayed.

Use to switch between settings and tu or 0~9 to adjust the value of a setting.

Type: Choose between View, Record or None.
Channel: Press oK to display the channel list and use to select the wished channel for this action.
Press Tv/RAD button to switch between TV channel and Radio channel list.
Confirm highlighted channel with oK button.
Title: Press oK if you want to give the Timer another name as “Manual Timer xx”.
Use the displayed keypad for insertion.
Repeat: Choose between Once, Daily, Weekly, Weekdays or Weekend.
Date: With repeat set to Once: press oK to display the calendar. Use to pickthe date for the recording and confirm it with oK. Then press EXIT to apply the date to the Timer setting.
With Repeat set to Weekly: Use to select the day of the week, at which you want the timer to start.
Time: Press oK and use the or oK and to choose the hour. Use buttons to enter the minute or oK and ****to choose the minute. Press EXIT to leave the setting.
Duration: Use the 0~9 buttons to digit the duration of the timer if you have selected Record.
Once all settings are made, Press RED Save button to store these settings and press EXIT to leave the Timer menu.

Delete a timer
In order to delete a set timer, select it with and press oK to select. Press blUE Delete button to delete and confirm with oK.

OTA SOFTWARE UPGRADE

OTA automatic

The OTA (Over the Air) function automatically takes care that your receiver check if the latest software is loaded.
Every time your receiver is switched to standby the OTA function will check for an improved software version. After detection of a newer version, your receiver will display a message, after you switched it ON again. Then you can download the new SW version. You can select OK to start the update immediately, or you can select Cancel to start next time. Be aware that download takes around 20 minutes. You can skip the update process only for five times, afterwards a forced download will be started.

WARNING

NEVER power off the receiver or pull the mains plug during the software upgrade process. Doing so might cause irreparable damage to your receiver and will void your warranty.

TROUBLESHOOTING

There may be various reasons for abnormal operation of the receiver. Please check the receiver according to the procedures as explained below. If the receiver does not work properly after checking it, please contact your local Service line or STRONG dealer. Alternatively you can send a support mail via our website: www.strong.tv. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty.

$STRONG-SRT-7805-Digital-High-Definition-Satellite-Receiver-fig- $15$$

SPECIFICATIONS

Demodulator

Demodulation: QPSK, 8PSK
Input symbol rate: DVB-S QPSK: 1 ~ 45 Ms/s
DVB-S2 8PSK/QPSK: 10~30 Ms/s
FEC decoder: Auto, 1/2, 2/3, 3/4, 5/6, 7/8 in DVB-S mode 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10 in DVB-S2 mode 3/5, 2/3, 3/4, 5/6, 8/9, 9/10 in 8PSK mode

video Decoder