Burris RT-1 RT-Series Compact Sights User Guide

: June 9, 2024
: Burris

Table of Contents

Burris RT-1 RT-Series Compact Sights
Compact Sights
2 MOA DOT
BALLISTIC 3X™
BALLISTIC 5X™
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Burris RT-1 RT-Series Compact Sights

Compact Sights

Burris RT sights are compact, ‘Close Quarters’ optics made for tactical carbines. Burris RT-1, with its 1x magnification and 2 MOA red dot, provides quick target acquisition for close or fast-moving targets. The RT-3 and RT-5 have illuminated reticles that are perfect for close to medium-range targets and feature easy-to-use bullet drop compensation for accurate shots out to 600 yards. Burris RT-1 RT-Series Compact Sights-FIG-1

2 MOA DOT

RT-1 Base
The RT-1 comes with a standard and a high base mount, both of which match the Trijicon® MRO® footprint.* Select the base that provides the best mounting height. To remove the base, use the supplied torx wrench to loosen the four screws on bottom of the sight. The base is symmetrical so there is no special orientation. Tighten the screws to 15 in-lbs. of torque and you’re ready to mount the sight on the rail.

TRIJICON and MRO are trademarks of Trijicon, Inc. Burris Company and its goods are not sponsored or endorsed by or otherwise affiliated with or related to Trijicon, Inc. or its products. Burris RT-1 RT-Series Compact Sights-
FIG-4

Mounting the Optic
Each sight comes factory-ready to mount to a Picatinny rail system. Using the supplied Torx wrench, loosen the screw(s) on the right side of the base to open the mount just enough to fit over the width of the rail. Once positioned on the rail, test for proper eye relief. Once properly located on the rail, use the wrench to tighten the base screw(s) to 45 in. – lbs.

Reticle Focus Adjustment
The RT-3 and RT-5 have a diopter adjustment ring on the ocular end which is used to sharpen reticle focus to your preference.

Battery Installation / Replacement
The RT-1, RT-3 and RT-5 are each powered by a single CR 2032 3V lithium battery. The battery compartment is on the right side of the sight. To open the compartment, turn the cap counter-clockwise. Drop in the battery with the positive side (+) face up and re-tighten cap completely. To preserve battery life, all RT sights are equipped with an Auto-Shut Off. The sight automatically turns off after 4 hours on the 4 brightest settings and 8 hours on the 3 night vision settings.

Red Dot / Reticle Illumination Adjustment
To activate the red dot on the RT-1 or illuminate the reticle of the RT-3 or RT-5, press any button on the top of the sight. Once the dot/reticle is illuminated, the forward and back buttons can be used to select any of the 7 brightness settings. To turn the sight off, press and hold the rear button on top of the sight for 4 seconds.

Windage /Elevation Adjustment
The elevation adjustment screw is located on top of the sight. The windage adjustment screw is located on the right side of the sight. Use a small screwdriver to adjust point of aim up and down or left and right. Arrows on the dial indicate direction of movement.

BALLISTIC 3X™

Stadia lines and center horseshoe are optimized for viewing at 3x magnification
Fine aiming lines for elevation and windage adjustment, precise shot placement at distance
Proven broken circle design with center dot for ultra-fast engagement at short distances
Illumination is daylight bright and won’t wash out in harsh light

BALLISTIC 3X DETAIL

RETICLE SUBTENSIONS (in Mils)

BALLISTIC 5X™

Versatile tactical reticle with milradian measurements.
Illuminated broken circle with center dot allows for ultra-fast engagement at short distances.
Trajectory compensation out to 600 yards.
Ideal for achieving long-range accuracy with 5.56 and .223 ammunition.

BALLISTIC 5X™ DETAIL