milleteknik D29 2 Plus 2 Output Module Instruction Manual
- June 11, 2024
- Milleteknik
Table of Contents
milleteknik D29 2 Plus 2 Output Module
Technical Specifications
- Product: 2+2 Output Module
- Features: Four fully protected load outputs (2 prioritized, 2 non-prioritized)
- Mounting: Plastic bracket inserted into battery backup
- Maximum Load : 5A per output, 10A total for the board
Product Usage Instructions
Mounting in Battery Backup
- Ensure the card is mounted in its plastic casing.
- If loose, snap it back into the plastic casing.
- Mount the card on any available slot in the enclosure, leaving space for cables.
- Important: Install the board before screwing on wiring or commissioning.
Connection to Motherboard
Connect the card following the provided diagram. Ensure that the load connections match (+ to +, – to -) between the motherboard and the option board.
Power Priority Explanation
Priority Load: In case of a power outage, priority loads are powered using reserve batteries.
Non-Prioritized Load: Non-prioritized loads will not be powered by reserve batteries during a power cut.
FAQ
- What does priority / non-priority load mean?
- Priority load: Powered by reserve batteries during power outages.
- Non-prioritized load: Not powered by reserve batteries during power outages.
TECHNICAL SPECIFICATIONS 2+2 OUTPUT MODULE
2+2 Output module is a protection module with four fully protected load
outputs, of which two load outputs are prioritized and two are non-
prioritized.
The card comes mounted in a plastic bracket that is inserted into the battery
backup. When ordering, check that the card fits the battery backup card to be
installed in.
What does priority / non-priority load mean?
Priority load means that in the event of a power outage (mains failure), the load will be powered on with the reserve power, (batteries), Non-prioritized load means that in the event of a power cut (mains failure), the load will not be powered further with the reserve power (batteries)
MOUNTING IN BATTERY BACKUP
The card is delivered mounted in it’s plastic casing, for easy installation.
If the card has come loose, snap it back into the plastic casing.
Mount the card on any card slot in the enclosure, leave space for cables.
Important
Install the board before screwing on wiring or commissioning.
SHORT DESCRIPTION 5 OUTPUT MODULE
Circuit Board Overview – 2+2 Output module
Caution
Maximum load per output is 5 A and total maximum load for the entire board is
10 A.
Use the supplied cable
Use the cable that comes with the box to connect the card.
CONNECT 2+2 OUTPUT MODULE TO MOTHERBOARD: CEO3 V2.1
Connect the card as shown in the picture.
+ and – from load on the motherboard are connected to + and – on the option
board.
Communication is connected between terminals as the solid line shows.
Connections from battery backup to fuse board
CONNECT 2+2 OUTPUT MODULE TO MOTHERBOARD: CEO3 V5 / CEO-ECO
Connect the card as shown in the picture
+ and – from load on the motherboard are connected to + and – on the option
board.
Communication is connected between terminals as the solid line shows.
Connections from battery backup to fuse board
CONNECT 2+2 OUTPUT MODULE TO MOTHERBOARD: NEO3
Connect the card as shown in the picture.
+ and – from load on the motherboard are connected to + and – on the option
board.
Communication is connected between terminals as the solid line shows.
Connections from battery backup to fuse board
CONNECT 2+2 OUTPUT MODULE FOR MOTHERBOARDS: PRO2 V3 15 A AND 25 A
Connect the card as shown in the picture.
Connections 15A and 25A units 
CONNECT 2+2 OUTPUT MODULE FOR MOTHERBOARD: PRO1 5 A AND 10 A
Connect the card as shown in the picture
+ and – from load on motherboard are connected to + and – on the option
board.
Communication is connected between terminals as the solid line shows.
Connections from battery backup to fuse board
CONNECT 2+2 OUTPUT MODULE FOR MOTHERBOARDS: PRO2 V3 5A AND 10A
Connect the card as shown in the picture.
+ and – from load on the motherboard are connected to + and – on the option
board.
Communication is connected between terminals as the solid line shows.
Connections from battery backup to fuse board
CONNECT 2+2 OUTPUT MODULE FOR MOTHERBOARDS: PRO2 V3 15 A AND 25 A
Connect the card as shown in the picture.
Connections 15 A and 25 A units
CONNECT 5 OUTPUT MODULE TO MOTHERBOARD: PRO3
Connect the card as shown in the picture.
+ and – from load on motherboard are connected to + and – on the option
board.
Communication is connected between terminals as the solid line shows.
Connections from battery backup to fuse board
IF THE CARD LACKS A WHITE (JST) CONTACT OR IF AN ALARM IS TO BE GIVEN VIA RELAY SWITCHING
Connect the card as shown in the picture.
+ and – from load on the motherboard are connected to + and – on the option
board.
Communication is connected between terminals as the solid line shows.
Connections from battery backup to fuse board
CONNECTION OF ADDITIONAL 2+2 OUTPUT MODULE
Connecting additional option cards to the motherboard
Note
For alarm connection use 2A and 2B for connection of newer devices (after
approx. 2018). For older devices (before approx. 2018) use 3A-3C
Connection of additional option cards
P3:1-3 NC, COM, and NO
Alarms from optional cards are connected on the terminal block (on the motherboard)
TECHNICAL DATA – 2+2 OUTPUT MODULE
Outputs
The article number of the manual 350-162
Manufactured in Milleteknik’s factory in Partille, Sweden.
This translation is not verified and should be cross-referenced with the
Swedish original before use.
ABOUT TRANSLATION OF THIS DOCUMENT
User manual and other documents are in the original language in Swedish.
Other languages are machine-translated and not reviewed, errors may occur.
SUPPORT
Do you need help with installation or connections?
Our support phone is available : Monday-Thursday 08: 00-16: 00 and Fridays 08: 00-15: 00. Telephone support is closed between 11: 30-13: 15.
You will find answers to many questions at: www.milleteknik.se/support
Phone: +46 31-340 02 30
Support is open : Monday-Thursday 08:00-16:00, Fridays 08:00-15:00.
Closed 11:30-13:15
Spare parts
Contacted support for questions about spare parts.
Support after the warranty period
Milleteknik provides support during the life of the product, but no longer than 10 years after the date of purchase. Replacement for an equivalent product may occur if the manufacturer deems that repair is not possible. Costs for support and replacement are added after the warranty period has expired.
Questions about product performance?
- Contact sales : 46 31-340 02 30,
- e-mail: sales@milleteknik.se
ADDRESS AND CONTACT DETAILS
- Milleteknik AB Ögärdesvägen 8 B S-433 30 Partille Sweden
- +46 31 340 02 30
- info@milleteknik.se
- www.milleteknik.com
- www.milleteknik.se
Milleteknik AB, Ögärdesvägen 8 B, 433 30 Partille
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>