b d R3W Roll A Door Instruction Manual
- June 1, 2024
- b d
Table of Contents
Series 3
installation instructions
These instructions are intended for professional garage door installers. All
references are taken from inside looking out.
DOC# 165019_07
RELEASED: 27/11/23
Before you start
1.1 installation safety warnings
This B&D Roll-A-Door is designed and tested to provide security, attractive
appearance and smooth , low effort operation provided it is installed and
operated in strict accordance with the following safety warnings. Failure to
comply with the following instructions may result in death, serious personal
injury or property damage.
NOTE: No guarantee will be given or responsibility accepted by the
manufacturers if the door is not installed as instructed.
WARNING!
Crush injury from unsecured door
| • Place a 2 metre exclusion zone around area under the garage opening while
installing door. If sufficient area is not available DO NOT install door.
• Do not move under a door while it is on the door support (or lifting
device).
• Follow the installation instructions.
• Fit door support (or lifting device) snugly under door before lifting.
• Ensure door support (or lifting device) is on flat ground.
• Ensure the door is immediately fastened to the bracket with the “U” Bolt.
• Ensure no-one walks under a door sitting on brackets.
---|---
Tension Springs| • Ensure door is correctly secured at all times when making
adjustments.
• Ensure the correct length pipe wrench is utilised.
• Ensure that pipe wrench is fitted correctly to the axle and if it is gripped
onto
the axle do not underestimate the tension in the spring when undoing the
clamps.
• Ensure correct bolts are tightened or loosened to ensure there is no release
or controlled release of energy from the spring through the pipe wrench.
• Keep head clear of the pipe wrench at all times.
ELECTROCUTION!| • Check risk assessment for any highlighted electrical
power concerns.
• Ensure power source is isolated prior to commencement of job.
• Turn off electricity to site when necessary.
• Wear rubber soled footwear.
LACERATION:| • Wear appropriate PPE (Dyneema cut off gloves) and keep
hands well clear of pinch points.
• Follow instructions explicitly, particularly for the installation of some
parts of the doors, as the unrolled cut out edges presents a very sharp edge.
CAUTION:
Muscular strain| • Practice correct lifting techniques when required to lift
the door.
• Use mechanical aids such as lifting devices, forklift and cranes where
possible.
• Avoid twisting.
• Use correct technique of knotted rope installation aids.
Fall from ladder| • Ensure ladder is the correct type for job.
• Ensure ladder is on flat firm ground that will take the weight without the
legs sinking.
• Ensure user has 3 points of contact while on ladder.
Hand Tools| • Wear appropriate PPE and utilise operators manual of all tools.
• Use appropriate noise/hearing protection in the form of ear plugs or ear
muffs.
• Ensure appropriate fire protection available and housekeeping to ensure that
flammable liquids or materials are removed from the area of work.
Entanglement| • Keep hands and loose clothing clear of moving door and guides
at all times.
TWO PERSON LIFT:| • When a mechanical aid is not used this product
requires a two person lift to raise onto the brackets. Use proper techniques
and equipment to lift the door from the trailer and up onto brackets.
1.2 substrate fastener recommendations
WARNING! Coach bolts/ screws are NOT suitable for windrated doors. Refer to
High Wind drawings on the B&D Website.
WARNING! The installer must select and use fasteners appropriate to the
material into which they are being fixed.
important notes
a) For installation to materials not covered in the chart, the installer
should seek expert advice from a qualified builder.
b) Minimum length of fastener does not exclude use of longer lengths. Decision
must be made by fitter to ensure adequate strength.
c) Recommendations for old materials or materials not in good condition are
not included. If in doubt about the strength of the material seek specialist
advice.
d) Fasteners for brackets in masonry should be at least 8mm x 75mm long or
metric equivalent.
e) Use the washers supplied in the parts bag to all fixings.
material| fastener type(s)| diameter or type| | length of
fastener
(see note)| BKT| GUIDE
---|---|---|---|---|---|---
New Solid Brick| Coach Bolts (Hex Lag Screw) and washers – combined with
wall plugs| 5/16”| xd| 50mm| | •
5/16”| x| 80mm| •| •
Macplugs (wall plugs) to suit above| 5/16”| x| 50mm| | •
5/16”| x| 80mm| •| •
HLC Sleeve Anchors (Dyna Bolts) with washers| 12mm| x| 55mm| •|
New Hollow Brick| Screw Masonry Flange Hex Head (M8 x75)| 8mm| x| 75mm|
•| •
New Solid Concrete| Coach Bolts (Hex Lag Screw) and washers – combined
with wall plugs| 5/16”| x| 50mm| | •
5/16”| x| 80mm| •| •
Macplugs (wall plugs) to suit above| 5/16”| x| 50mm| | •
5/16”| x| 80mm| •| •
HLC Sleeve Anchors (Dyna Bolts) with washers| 12mm| x| 55mm| •|
Steel Framing e.g. BHP Framing (with rear access)| Hex Head Bolt
Zinc Plated, Hexagon Nuts Zinc Plated, Washers Zinc Plated| 5/16”| x| 1”| | •
3/8”| x| 1”| •| •
10mm| x| 25mm| •| •
12mm| x| 25mm| •|
Heavy Gauge Steel| Hex Head Tek and washers| 14-20| x| 22mm| •| •
Light Steel Framing e.g. BHP House Framing (no rear access)| Heavy
Duty Kap Toggle| 10mm| x| 100mm| •| •
12mm| x| 100mm| •|
Hex Head Tek and washers| 6-10| x| 20mm| | •
New Timber| Coach Bolts (Hex Lag Screw) and washers| 5/16”| x| 50mm| | •
5/16”| x| 80mm| •| •
Hex Head Tek and washers| 14-10| x| 50mm| •| •
BRICK CONSTRUCTION| STEEL CONSTRUCTION
---|---
SECURE GUIDE| MASONRY BLOCK CONSTRUCTION
WARNING! Masonry blockwork should be properly filled and reinforced if
brackets are to be mounted directly to blockwork with masonry anchors. Where
the blockwork is not solidly filled but structurally sound, long bolts should
be passed through the blockwork using suitable steel plates under bolt heads.
Special consideration should be given to brick type and construction of wall,
to ensure satisfactory fixing e.g. welding detail if fixed to steel.
1.3 preparation
WARNING! If you need to remove an old door prior to installing a B&D door
ensure to:
- Roll the door up and place a secure tie around the middle
- Place door support on flat ground
- Fit door support snugly under door before loosening the brackets or locating U bolts.
- Slowly undo bolts to release the spring tension and the door from the brackets.
- Slowly lift the door from the brackets keeping it balanced as it is lowered to the ground.
1.4 before installation
1.4.1 requirements
mounting – The door is designed to be mounted behind the opening.
obstructions – Ensure that the surface where the door will be fitted is flush
and smooth, and the area behind the opening is free from any protrusions.
structural suitability – Ensure the opening is strong enough to support the
door. If unsure, consult a builder.
level and plumb – The door must be installed in an absolutely level position,
if opening is not level and square, appearance and/ or sideroom requirements
will be affected. The floor should be level or recessed across the opening to
avoid gaps.
DO NOT CUT THE PACKAGING THAT HOLDS THE DOOR IN A ROLL
At a later stage during the installation you will be told just when to cut the
packaging. Remove brackets, guides and bag of small parts from each end of the
door roll.
1.4.2 measurements
opening width – As the standard door overlaps each side by 50mm or more, the
door should be 100mm wider than the opening. A wider door can be fitted as
long as additional sideroom and fixing is available.
(Fig 1.4.1a) Wind-Locked doors require additional overlap dependent on the
substrate, consult the B&D High Wind Certification Drawings for more detail.
opening height – The door opening height (or drive through clearance)
indicates the distance between the ground and rubber seal at the bottom of the
door, with door fully open. Max drive through heights for each door height are
listed in Fig 1.4.1b.
headroom – A minimum headroom is required for all doors. Refer to Fig 1.4.2 –
1.4.5 for measurements. If the door is installed lower into the opening than
shown in Fig 1.4.2, additional loss of door opening height will result.
backroom – refer to Fig 1.4.2 – 1.4.5 for measurements. ![b d R3W Roll A Door
- measurements](https://manuals.plus/wp-content/uploads/2024/04/b-d-R3W-Roll-A -Door-measurements.png)Fig: 1.4.1b
Description| Nam Type| Rollmasta| Squareline Deluxe|
Industrial
---|---|---|---|---
Series 3| Series 3| Series 3
Model code| R3F| R3W| R3I
Door & Max Drive Through Heights (mm) (non-Wind-Lock Doors)| Door Height| Max
Drive Height| Door Height| Max Drive Height| Door Height| Max Drive Height
1200| 1200| –| –| 1200| 1200
1800| 1700| 1800| 1700| –| –
2100| 2000| 2100| 2000| 2100| 2000
2400| 2300| 2400| 2300| 2400| 2300
2700| 2600| 2700| 2600| 2700| 2600
3000| 2900| 3000| 2900| 3000| 2900
–| –| –| –| 3300| 3300
–| –| –| –| 3600| 3600
Max Door Width (including overlap)| 5100mm| 5500mm| 5500mm
1.4.2 measurements continued… Fig: 1.4.5
NOTE: All measurements are in millimeters ( mm )
Windlocked Steel Substrate Windlocked Masonary Substrate
A1 Based on a Controll-A-Door PowerDrive and GDO-12 Hiro.
A10 Based on a GDO-10 Toro (Right Hand Side install). Refer to GDO-10 installation manual for LHS installations.
If an opener is installed there is no H measurement required.
D1 & D2* are the minimum measurements and optimum backroom clearance required
for installation.
NOTE: Wind-Locked doors may need between 55 – 68mm curtain overlap on both
sides, depending on the substrate used.
^ R3F has a maximum width of 5100mm.
NOTE: It is not recommended that doors fitted in restricted headroom be
fitted with openers.
1.5 parts checklist
SERIES 3 ROLL-A-DOOR | R3F & R3I | R3W | HW |
---|---|---|---|
ITEM | DESCRIPTION | QTY | QTY |
A | ROLLED PLASTIC WRAPPED DOOR | 1 | 1 |
B | BRACKETS, LEFT AND RIGHT HANDED | 2 | 2 |
C | DOORS GUIDES LEFT AND RIGHT HANDED | 2 | 2 |
D | STEEL LOCKING BARS | – | 2 |
SMALL PARTS BAG CONTAINING | |||
E | BOTTOM RAIL STOPS AND SCREWS | 2 | 2 |
F | FACEPLATE AND LOCK ASSEMBLY | – | 1 |
G | MUSHROOM HEAD SCREWS FOR LOCKING BAR | – | 2 |
H | LOCKING BAR COVERS | – | 2 |
I | LOCKING BAR RETAINER | – | 2 |
J | U-BOLT BRACKET SADDLES | 2 | 2 |
K | CAST SADDLES WITH BOLTS | 2 | 2 |
L | NUTS & WASHERS FOR “U” BOLTS / SADDLES | 4 | 4 |
M | SMALL WASHERS (DOOR SIZE DEPENDENT) | 8-12 | 8-12 |
N | LARGE WASHERS | 4 | 4 |
1.6 initial calculations
a) Measure the opening width of garage.
b) Measure the door curtain width.
c) Calculate over lap for each side: door width – opening width ÷ 2 = over
lap
d) Mark the line for the edge of door curtain (over lap) on each side of the
opening.
-
Standard Series 2 doors
= 50mm (minimum) overlap each side -
Windlock (HW) Series 2 doors
= 55+mm (minimum) overlap each side
installation
2.1 install first bracket
dimension panel
Recommend| height (mm)| width (mm)| A| B| C|
E| F
A1/ A10| A2
Opener| Chain
up to 2100| up to 5500^| 170 / 275| N/A| 135| 535| 260| 275
2101-2400| 135| 535| 260| 275
2401-2700| 185| 135| 535| 260| 275
2701-3000| 135| 565| 275| 290
3001-3300| up to 3600| 135| 565| 275| 290
3301-3600| 135| 565| 275| 290
Restricted| up to 2100| up to 5500^| N/A| 135| 475| 260| 215
2101-2400| 135| 475| 260| 215
2401-2700| 185| 135| 475| 260| 215
2701-3000| 135| 535| 275| 260
3001-3300| up to 3600| 135| 535| 275| 260
3301-3600| 135| 535| 275| 260
Wind| up to 2400| up to 5500^| 200 / 305| N/A| 185| 535| 260| 275
220 / 325| 205| 535| 260| 275
2401-3000| 200 / 305| 225| 185| 565| 275| 290
220 / 325| 245| 205| 565| 275| 290
Fig: 2.1.1
NOTE: All measurements are in millimeters ( mm )
Windlocked Steel Substrate Windlocked Masonary Substrate
A1 Based on a Controll-A-Door PowerDrive and GDO-12 Hiro.
A10 Based on a GDO-10 Toro (Right Hand Side install).
Refer to GDO-10 installation manual for LHS installations.
^ R3F has a maximum width of 5100mm.
NOTE: It is not recommended that doors fitted in restricted headroom be
fitted with openers.
Take note of drive through clearance heights in fig 1.4.2b as the bottom rail
will hang into the opening on some doors, therefore reducing the opening.
a) Use above diagrams F i g 2.1.1 and 2.1.2 for head and sideroom clearances.
b) Mark three hole positions using slots of the bracket B.
c) Drill holes, then attach bracket using six 10mm (3/8”) bolt size masonry
anchors; (dynabolts or similar). WARNING! The structure substrate must conform to the DTCM
requirements. Refer to bac.nt.gov.au for the DTCM Manual or High Wind drawings
on the B&D Website.
2.2 install second bracket
a) Using a water level mark the position for the second bracket (Fig 2.2.1)
b) Re-check levels then drill and fix as with first bracket.
CAUTION: The brackets must be perfectly level for the door to operate. 2.3 place door on
brackets
TWO PERSON LIFT: this product requires a two person lift to raise onto the
brackets. Use proper techniques and equipment to lift the door from the
trailer and up onto brackets.
CAUTION: DO NOT CUT THE PLASTIC WRAP OR PACKAGING YET
a) Check the axle length and cut if sideroom is limited. Before cutting, make
sure the floating axle is free and centred (Fig 2.3.1). Centre will be found
by rotating the axle a quarter turn in either direction then releasing . With
centre found, make a clear mark on the axle against the hub for later
reference.
b) With the door the correct way round (the curtain rolls down the rear of the
opening) carefully lift door onto the brackets using block and tackles
attached to the door axles, or other suitable lifting equipment – to avoid
curtain damage.
c) Loosely fit “U” bolt saddle J and/or cast saddle K double saddle
and position the door so that it overlaps the opening evenly both sides so
that the axle is positioned on the bracket arm slots as far forward as
possible (Fig 2.3.2) Fitting the saddles eliminates the door falling from the
brackets.
d) Centre the door with the opening, while ensuring the floating axle is also
centred with the door.
Do this by lining up previous marks with the hub, then lift both the axle and
the door together until it is centred with the opening.
Rotate both the door and the axle so that the bottom rail is level with the
arm of the bracket.
e) Now tighten the“U” bolts saddle J , or double saddle k (door size
dependent), using washers under nuts L , to a torque of 40 newton metres
or 30 ft.lb.
2.4 install guides
2.4.1 positioning guides
WARNING! Do not grease the guides. Grease will damage the Nylofelt®
running strips and make doors heavier to operate.
CAUTION: Restricted headroom installation is not recommended for
automated doors unless the door is installed lower into the opening.
NOTE: This will reduce the drive through height.
dimension panel
Recommend| height (mm)| width (mm)| G
up to 2100| up to 5500^| 0
2101-2400| 0
2401-2700| 0
2701-3000| 0
3001-3300| up to 3600| 0
3301-3600| 0
Restricted| up to 2100| up to 5500^| 60
2101-2400| 60
2401-2700| 60
2701-3000| 30
3001-3300| up to 3600| 30
3301-3600| 30
Wind| up to 2400| up to 5500^| 0
0
2401-3000| 0
0
R3F has a maximum width of 5100mm
WARNING! All High Wind installations must adhere to fixing types and
centres as referenced in the DTCM Drawings and B&D High Wind Drawings.
If securing to uneven brickwork, packers may be required behind clips, to
prevent them twisting out of square; also ensure that clips are positioned on
secure bricks.
a) Check that curtain overlaps equally on both sides.
b) Check that guides C are the correct length, that is, starts level with
the brackets (or as per table above at position G). (Fig 2.4.1) If guides need
to be shortened cut from bottom of guide.
c) For Series 3 Doors:
(i) Now position one guide over the edge of the door curtain. Mark and drill
the top fixed guide clip and secure using correct fixing and washers as per
table in Section 1.2, allowing 3-4mm clearance between the door and the inside
of the guide.
(ii) Ensuring guide is plumb, using spirit level, then drill and fix remaining
clips and head stop.
For Series 3 Windlock Doors:
(i) If there is limited sideroom available the guide may need to have the side
cut out to accommodate. See Fig 2.4.2 for recommended and restricted sideroom
with a clearance of 2-5mm to the bottom rail roller.
(ii) Now position one guide over the edge of the door curtain. Mark and drill
at top guide hole and secure guide using fixing types as per High Wind
Certification Drawings, taking note of the specific spacing requirements.
(iii) Ensuring guide is plumb, drill and fix remaining holes in guide as per
spacing details listed.
d) With the top of the 2nd guide level with the first, repeat (c) for the
specific door type. 2.5 tension the
springs
WARNING! Once the packaging containing the door roll is cut, the door
will have a strong tendency to rise and revolve. If uncontrolled, the rapidly
unrolling door could cause damage or injury.
2.5.1 tensioning and adjustments
a) Ensure that the bottom rail and axle is turned as one to the position shown
in Fig 2.5.1.b) Ensure both “U” bolts are tightened, then –
-
Rotate the door approximately 2 complete turns in a forward direction to apply tension.
Do not let go as the springs are now tensioned.
See arrow in Fig 2.5.1. -
Hold the door firmly, NOW cut the plastic wrap along the bottom rail (taking care not to damage door surface).
c) Pull the curtain down slowly into the guides below the head stop in Fig
2.5.2.d) Fit
bottom rail stops E using self locking nuts provided. Allow the door to
rise and rest against head stops Fig 2.5.3. e) Test the door operation by moving it up
and down. The curtain must feed in smoothly without bumping.
f) Reposition the guides as necessary to allow smooth and even operation with
clearances shown below throughout. See images in Fig 2.5.4 for each specific
guide / wind region adjust lead in as required Step 2.5.2. 2.5.2
creating proper guide lead-in
The shape of lead-in is critical for successful door operation and trouble
free performance. The shape of lead-in needs to be formed by the installer,
refer to (fig 2.5.5).
a) With multigrips, bend top 5mm of lead-in approximately 45° to prevent
Nylofelt® catching on lead-in.
b) Bend lead-in from door stop to top of lead-in (along press cut), to finish
15mm from its original position.
c) Check top of guide lead-in to ensure that the door does not make contact
when rotated. Damage to Nylofelt® could result. Installer may need to increase
the 15mm dimension for larger door heights to ensure the smooth operation of
the door.
WARNING! For all doors that are fitted with openers. To reduce the risk
of damage to persons or property, be sure to cut off any excess thread of the
screw that protrudes the weight bottle and file any burs.![b d R3W Roll A Door
- tension the springs 6](https://manuals.plus/wp-content/uploads/2024/04/b-d
-R3W-Roll-A-Door-tension-the-springs-6.png) 2.6 locking
2.6.1 centre lift lock (only with R3W & R3F)
a) Fit faceplate to outside of door. Fit hooks onto edge of aperture then slide faceplate as far to the right as possible. Use adhesive tape to hold in position Fig 2.6.1.
b) Attach the lock body to the faceplate from the inside, using screws supplied. Do not overtighten the screws.
c) Pull the curtain down slowly into the guides below the head stop.
d) Assemble locking bar to retainer and through plastic edge retainer. Mark the position of lock bar on side of guide. Transfer location mark to inside back face of guide and drill a file slot 10mm wide x 25mm long. Equally spaced on centre line of guide. Allow approximately 5mm clearance from top of slot to top of locking bar.
e) Slide bars through guide slot, then back onto lock arms. Screw on securely using 4mm x 6mm screws supplied.
f) Fit locking bar covers H to cut outs on each side.![b d R3W Roll A Door - locking](https://manuals.plus/wp-content/uploads/2024/04/b-d-R3W-Roll-A
-Door-locking.png) 2.6.2 internal waist high slide bolt (R3I)
(left hand side shown – viewed from inside)
With door fully closed check that bolt slides through guide. Adjust hole if necessary.
2.6.3 high wind centre lift lock (only with R3W & R3F)
a) Undo screws to separate lock from faceplate.
b) Fit faceplate to outside of door. Fig 2.6.3. Fit hooks onto curtain edge,
then slide faceplate as far to the right as possible. Use adhesive tape to
hold in position. c) Attach the lock body to the faceplate from the
inside, using the mounting screws and washers. Do not over-tighten the screws.
d) Attach self adhesive lock bar retainers. For additional strength drill 2 x
1/8 holes from inside using retainer as a template and fit 2 x 1/8 pop rivets
to each retainer from the face of the door.
e) With the door in the closed position make the lock hole position in the
side guides.
f) Drill and file out a slot:
i) NO PADLOCK – no longer than 32mm and no wider than 10mm as in Fig 2.6.4a.
Ensure top of the slot remains in line with top of locking bar.
ii) WITH PADLOCK – create slot as per i) then, additional 2 holes no smaller
than 20mm, positioned central to slot for waist high lock as in Fig 2.6.4b.g) Slide
bars through guide slot, then back, onto lock arms. Screw on securely using
4mm x 6mm screws supplied.
h) For bottom rails with shoot bolt locking refer to Fig 2.6.5. a) For
fitting optional padbolt type locking, refer to Fig 2.6.6. NOTE: Please contact your B&D
representative for all other lock solutions
2.7 troubleshooting
Symptom | Possible cause | Remedy |
---|---|---|
Door is hard to operate in ANY DIRECTION | Door jamming in the guides | Check: |
a) the guide clearances
b) the guides are plumb
c) that the guide surfaces are clean and free from oil
d) that the locking bars are the correct length
e) that the weatherseal is correct length
The door is hard to operate in ONE DIRECTION| The spring tension requires
adjustment| a) if the door is hard to lift, but tends to drop, refer to step
2.9 to increase the spring tension
b) if the door is hard to close, but tends to rise, refer to step 2.9 to
decrease the spring tension
If the door rolls up crooked| Brackets are not level Guides are not plumb Axle
is not centred| Make sure brackets are level, refer to step 2.2.
Make sure the guides are plumb, refer to step 2.4.
Centralise the axle, refer to step 2.8.
2.8 centralise the axle when door is mounted
WARNING! Ensure that pipe wrench is fitted correctly to the axle and if
it is gripped onto the axle do not underestimate the tension in the spring
when undoing the clamps.
CAUTION: THIS ADJUSTMENT REQUIRES 2 PERSONS TO COMPLETE. If the door
rolls up crooked with the RIGHT HAND SIDE higher than the left proceed as
follows:
a) Roll the door up as high as possible and tie two ropes around the door roll
approximately 300mm from each end, as a safety precaution.
b) With a person at each end of the door, hold the axle firmly with a large
pip wrench (Stillson) at least 450mm long.
c) Loosen the “U” bolt nuts at both ends and KEEP A FIRM GRIP ON WRENCH.
d) Move the axle to the RIGHT between 20 – 40mm.
e) Re-tighten “U” bolts before releasing pipe wrench.
f) Test and repeat if further adjustment in needed.
g) If the door is stiff to work or rattles over lead-in on top of guide, then
refer to Step 2.4. If the door rolls up crooked with the LEFT HAND SIDE higher
than the left proceed as follows:
a) Roll the door up as high as possible and tie two ropes around the door roll
approximately 300mm from each end, as a safety precaution.
b) With a person at each end of the door, hold the axle firmly with a large
pip wrench (Stillson) at least 450mm long.
c) Loosen the “U” bolt nuts at both ends and KEEP A FIRM GRIP ON WRENCH.
d) Move the axle to the LEFT between 20 – 40mm.
e) Re-tighten “U” bolts before releasing pipe wrench.
f) Test and repeat if further adjustment in needed.
g) If the door is stiff to work or rattles over lead-in on top of guide, then
refer to Step 2.4.
2.9 adjusting spring tension
WARNING! Ensure that pipe wrench is fitted correctly to the axle and if
it is gripped onto the axle do not underestimate the tension in the spring
when undoing the clamps.
CAUTION: THIS ADJUSTMENT REQUIRES 2 PERSONS TO COMPLETE.
a) With the door rolled up tie two ropes around the door roll approximately
300mm from each end, as a safety precaution.
b) With a person at each end of the door, hold the axle firmly with a large
pipe wrench (Stillson) at least 450mm long.
c) Loosen the “U” bolt nuts at both ends and KEEP A FIRM GRIP ON WRENCH.
d) Rotate the axle in the required direction (Fig 2.9.1).
e) Re-tighten the “U” bolts to a tension of 40 Newton metres or 30 ft.lbs
BEFORE releasing pipe wrench.
f) Test and repeat if further adjustment is necessary.
appendix
3.1 after installation care
cleaning
COLORBOND® and coloured steel FINISH DOORS: Your B&D Roll-A-Door® door has
been pre-painted with a high durability polyester paint system especially
designed and tested for the harsh Australian conditions. However, all exposed
surfaces require some attention to guard against the premature onset of
corrosion and any other harmful atmospheric effects. In our atmosphere there
are harmful deposits that gather on the door surface and if not removed
regularly, will seriously affect the appearance and life of the door.
Washing of the door with clean water and a cloth every 14 days is recommended
– particular care should be taken to clean areas of the door not normally
washed by rain, including the top of the door roll inside the garage.
NOTE: In locations where there is likely to be salt in the air or
industrial fallout is severe, more frequent washing is advisable and
additional protection of the surface maybe required.
Touch-up paint, if required, is available from your B&D dealer.
lock
Your lock does not require special maintenance, however, if the keyway
becomes stiff, the application of powdered graphite is recommended – do not
grease or oil the lock.
The faceplate should be washed with soapy water and rinsed well. Strong
solvents, such as acetone, should not be used – these will damage the surface.
WARNING! Do not disassemble the lock mechanism.
When opening the door, always make sure the key is with drawn from the lock –
if this is not done, the lock mechanism could be damaged and the key bent or
broken.
We suggest you record your full Key letter and Number on the front of this
manual and if replacement keys are required they can be obtained from your
nearest B&D office, simply by quoting this number. If the keys have been lost
and the number not recorded, it can be found stamped into the locking arm at
the back of the mechanism.
NYLOFELT®
On no account should you use grease or oil in the door guides or on the
Nylofelt® running strips – the grease or oil will clog the Nylofelt® and spoil
the operation of the door. An occasional wipe with a cloth dampened with
mineral turps or methylated spirits, down the inside of each guide, is very
beneficial in removing any trace of grease or dirt.
After the guides have been cleaned, a silicon spray may be used in the guides.
NOTE: WD40 or similar oil based sprays are not silicon and should not be
used.
Care should be taken not to damage the Nylofelt®, however, if Nylofelt® is cut
or damaged, a lighted match should be used to quickly seal the ends of the
nylon braiding, so as to stop any further deterioration.
regular maintenance required
B&D recommenas that you check the operation of your Roll-A-Door® at least
every six months (more regularly in extreme environments or frequent use). The
effort required to manually open and to manually close the door should be
about the same (if door has an automatic opener, put into manual mode before
testing door). If the door is difficult to operate in either direction (up or
down) then check:
- that the Nylofelt® running strips on each side of the door have not slipped from the edge and are jamming the door;
- that the door is running correctly in the guides and the guides are straight and perpendicular; and
- that the inside surfaces of the guides are clean and free of obstructions. (see paragraph on care of Nylofelt®)
If you have checked these (and corrected where necessary) and the door is
still difficult to operate, , then your door will need a service to adjust the
spring tension and possibly other operational parts of the door. This service
should only be carried out by an experienced door technician, using the
correct tools.
If you have an automatic opener fitted to your door, it is particularly
important that you ensure the optimum operation of the door, otherwise you may
reduce the effective life of the opener.
To keep your door running well, it is recommended that your door be serviced,
by an experienced door technician, every 12 months (more regularly in extreme
environments or frequent use), or earlier if required.
spring tension
It is natural for springs to lose tension over time. When spring tension is
adjusted or when your door is first installed it is usual to apply a little
more tension than is required for balanced operation, to allow for the normal
“settling in” of the springs.
warranty
Warranty conditional on proper care as recommended above. Full details of
the warranty are available from your nearest B&D office or visit the B&D
website www.bnd.com.au
b &d doors office locations
Head Office | 6-8 Fiveways Blvd, Keysborough 3073 | Phone (03) 9791 2000 |
---|---|---|
New South Wales | 34 Marigold St, Revesby 2212 | Phone (02) 9722 5555 |
Queensland | 17 Oasis Court, Clontarf 4019 | Phone (07) 3883 0200 |
Victoria | 147-153 Canterbury Rd, Kilsyth 3137 | Phone (03) 9237 7766 |
South Australia | 23 Frederick Rd, Royal Park 5014 | Phone (08) 8440 4747 |
Western Australia | 96 Mulgul Rd, Malaga 6090 | Phone (08) 9247 8777 |
International/Export | 34 Marigold St, Revesby 2212 | Phone +61 (0)2 9722 5555 |
your representative is……………………..
Prefixed trademarks are the property of
B &D Australia Pty Ltd.
B&D Doors & Openers is a division of B&D Australia Pty Ltd. ABN 25 010 473
971.
© 2018 B&D Australia Pty Ltd.
www.bnd.com.au
Documents / Resources
| b d
R3W Roll A
Door
[pdf] Instruction Manual
R3W Roll A Door, R3W, Roll A Door, A Door, Door
---|---
References
- Home - Building Advisory Committee - NT Government
- B&D Garage Doors - Safe and Secure Australian Garage Doors - B&D Australia
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>