MOZA RACING CRP Racing Ecosystem Pedals User Manual

: June 9, 2024
: MOZA RACING

Table of Contents

CRP Racing Ecosystem Pedals
Product Description
CRP Pedal Installation
Pedal Spacing Adjustment
Pedal Surface Angle Adjustment
Accelerator Force and Stroke Adjustment
Brake Force Adjustment
Clutch Adjustment
Comparison Table of Spring and Rubber Damping Block Strength
Warranty Conditions
**EU Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CRP Racing Ecosystem Pedals
User Manual MOZA RACING CRP Racing Ecosystem
Pedals Racing Ecosystem

CRP Racing Ecosystem Pedals

Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device, please contact the customer line.
www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer
Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz

Product Description

CNC Aluminium Alloy
100KG/220lbs load cell sensor
Three e-stage clutches
Organ type accelerator
Adjustable resistance, angle, and Travel.
Tunning by Experienced Drivers

CRP Pedal Installation

Install the pedals to the bottom plate and adjust the position. Install the screws and gaskets for each pedal. In order to ensure the stability of use, it is recommended to install all 6 screws for each pedal.
Mount the baffle horizontally, align both ends, and the tighten, and secure it to the base with the M4 screws.
Insert the interface of the throttle line into the throttle interface found in the control module at the bottom of the brake. Connect the clutch line to the clutch interface in the control module, connect the elbow type-B end of the USB line to the USB interface in the control module, and connect the other end to the PC.
The Working status of CRP Pedal can be viewed in the MOZA Pit House. (if the device is still grey or there is no response after stepping on it, please unplug the USB interface at the PC end, close the pit house, re-connect the USB interface, and reopen the MOZA Pit House)
The start, end and travel of the pedal can be set in MOZA Pit House.

Pedal Spacing Adjustment

Adjust the pedal forward or backwards. Use the included screws to secure the pedal once the correct position has been found. MOZA RACING CRP Racing
Ecosystem Pedals - fig 4

Pedal Surface Angle Adjustment

Use a hexagon screwdriver counter clockwise to loosen the screw on the face of the pedal. Use your hand to turn the nut to change the angle of the pedal. To lock in the
pedal’s position just secure the screw on the face of the pedal. The pedal adjustment methods for accelerator, brake, and clutch are the same. MOZA
RACING CRP Racing Ecosystem Pedals - fig 5

Accelerator Force and Stroke Adjustment

Twist the adjusting nut to change the Accelerator stroke Rotate the adjusting nut on the upper part of the spring by hand. Moving downward will shorten the throttle stroke. Accordingly, the starting force of the throttle will increase, and the ending force will remain unchanged. MOZA RACING CRP Racing
Ecosystem Pedals - fig 6

Brake Force Adjustment

Change the spring to adjust braking force.
Loosen the screw with M5 wrench, take out the screw and pin shaft, turn counter clockwise, and take out the spring assembly. Turn counter clockwise the flat nut removes the spring assembly.
To push out the spring and shaft, depress the spring. Then turn the flat nut clockwise to unscrew. Swap in the different spring, screw back on the caps. The spring sleeve should be flush with mounting hole, insert the pin and tighten the screw.
Replace the damping block and change breaking force
Remove the two screws on the side with the M5 wrench. Turn the decorative cover plate downward, take out the pressure sensor fixing plate, take out the rubber pad, replace the corresponding rubber pad. Then reassemble.

Clutch Adjustment

Replace the near end spiring and change the separation force curve.
Turn the bolt to take out the spring. Replace the corresponding spring. To test press the pedal’s surface by hand.
Adjust the clutch mounting position to change the clutch force

Comparison Table of Spring and Rubber Damping Block Strength

| Spring| Damping block
---|---|---
Colour/Type| Black| Yellow| Red| Soft| Medium| Hard
Brake| | Middle| Hard| Soft| Medium| Hard
Clutch| Soft| Middle| | | |

For more information and teaching videos, please visit the official website (MOZARACING.COM)

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase. The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
Natural wear and aging of consumables or components during use (such as batteries, etc.).
Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

**EU Declaration of Conformity

**

Identification data of the manufacturer’s / importer’s authorized representative:
Importer: Alza.cz a.s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
CIN: 27082440
Subject of the declaration:
Title: Pedal
Model / Type: Moza CRP Pedal
The above product has been tested in accordance with the standard(s) used to demonstrate compliance with the essential requirements laid down in the Directive(s):
Directive No. 2014/30/EU
**** Directive No. 2011/65/EU as amended 2015/863/EU

WEEE
This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU).
Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.