MOZA RACING 0.50.RBD501A R5 Racing Simulator User Manual
- June 4, 2024
- MOZA RACING
Table of Contents
RACING 0.50.RBD501A R5 Racing Simulator
User Manual
R5 Direct Drive Wheel Base
ES Steering Wheel
SR-P Lite Racing Pedals
R5 Direct Drive Wheel Base
Product Features
• 5.5 Nm Peak Torque | • Intelligent Temperature Control System |
---|---|
• Servo Direct Drive System | • 15-bit Resolution |
• Aviation-grade Aluminum Alloy | • MOZA Pit House Control Center Software |
• Ultra-low Torque Ripple and Cogging | • MOZA App Cloud Control |
Wheelbase Interface
Basic Parameters
Installation Guide
- Fix the base to the bracket through the 2-4 screw holes on the bottom of the base.
- Insert the Type-Bend of the USB cable and power cable into the corresponding ports on the rear of the RS base.
- Short press the power button (located on the rear of the RS base) to power the RS.
- Navigate to MOZA Racing (www.mozaracing.com) and download the latest version of the MOZA Pit House Software Suite. Install it and start your racing journey!
- For installation videos and further information, visit our official website (www.mozaracing.com)
Desk Clamp Installation Guide
Align the four screw holes on the bottom of the base with the mounting holes on the desk clamp and fix it to the desk clamp with 4 screws. Tighten the knobs on the desk clamp to the desktop and be sure to tighten up the knobs again to avoid the desk clamp from loosening and falling off during intense driving.
Precautions
- Never expose the unit to rain or water to avoid fire/ electric shock.
- Do not expose the unit to direct sunlight for extended periods as this may damage the unit.
- Excessive use may cause health risks to users, for the average user it is recommended to use no more than 2 hours a day.
- The RS is not suitable for children under the age of 6, and smaller parts may present a choking hazard.
- Children under the age of 13 should be accompanied by a guardian when using the RS.
- It is forbidden to disassemble the device without the permission of MOZA, otherwise, the user voluntarily voids their warranty.
- The RS must be connected to a safe electronic power supply.
- If repair or replacement is required, only conduct this with MOZA directly or with relevant authorized repair centers.
- Non-standard power supplies are prohibited from using
- Use only AC power provided by a standard wall outlet to avoid damage to the RS
- Do not expose the device to heat sources as this will damage the RS
- If the RS will not be used for an extended period, unplug the device
- If you find an abnormality with the RS, please stop using the device immediately and contact MOZA directly or a relevant authorized dealer/center.
- Please follow the MOZA official website or relevant social media for the latest information on the RS or related products.
This product is designed as a simulator! Please remember to distinguish simula tions from reality and drive safely!
Software Introduction
MOZA Pit House is MOZA’s one-stop software solution for the MOZA ecosystem.
Here, users can check the status of all their connected MOZA devices, This
also allows for vast configurations, including setting the base angle of the
wheel, force feedback, pedal adjustments, HUD settings, game settings, and
more.
It also allows for the quick starting of relevant games if they have been
detected on the computer.
The included presets allow beginners to quickly select a comfortable setting and get started in the world of racing, whereas more professional players have access to detailed and advanced configurations of their MOZA products should they wish to adjust.
One of our latest additions is the FFB Effect Equalizer, which allows for adjustments to give the best feeling of the road through the steering wheel as well as other surfaces such as grass, or dirt).
Our one-click update system allows for a fast and seamless upgrade of the entire MOZA ecosystem, allowing users to quickly get into the action
For further software instructions, visit the official MOZA Racing website (www.mozaracing.com) help center page to download the latest instructions and manuals.
Product Parameters
Supported Platform PC
Drive Form: Direct Drive
Maximum Turning Angle: Unlimited
Base Material: Aviation-grade Aluminum Alloy
Base Color: Black
Maximum Torque Output: 5.5 Nm
put Voltage: 110V-220V AC –>12V DC
Resolution 15. bit
USB Refresh Rate 1000Hz
App Functionality: Supported
Quick Release System: Supported
Interface: Base, Power Port, Data Port, Display Support, Pedal Interface
Accessories: Product Manual and Warranty Card, Power Supply, Data Cable,
Toolkit
Installation Method 4 screws on the bottom of the base
Desktop Mount: Included
Online Firmware Upgrade Function: Supported
ES Steering Wheel
Product Description
- High-grade Leather and Stitching
- Aluminum Alloy Frame
- MOZA Racing Custom Quick Release
- Aluminum Alloy Shifter Paddles
- 22 Configurable Keys
- MOZA Flow Shift Color Indicator Lighting
Quick Release Instructions
- Align the 6 steel balls on the steering wheel with the 6 grooves on the wheelbase.
- Press the wheel into the wheelbase, keeping the balls aligned with each other.
- The quick release will automatically snap into place, locking the wheel to the base. If the quick release does not lock, try rotating the panel on the base to its default position, and try again until it locks correctly.
- To remove the wheel from the base, simply use two hands to pull back on the outer ring (black color) and pull the wheel out at the same time.
Wheel Configuration
Using MOZA Pit House, our software suite, the ES steering wheel can easily be
set up and configured to your liking.
- Joystick Mode: Can be configured as buttons or keys.
- Indicator Light Switch: Allows for switching the indicator light off, on, or specific speed settings.
- Indicator Light Display Mode: Divided into two modes, toggled in the MOZA Pit house suite.
- Speed Adjustment: Adjustable according to speed and the timing of the shift indicator light, with different presets available.
- Brightness Adjustment: Allows for adjusting of the brightness of the shift indicator.
(For further information on specific steering wheel settings or functions using the MOZA Pit House Suite, visit our official website at www.mozaracing.com)
Product Parameters
Wheel Material: Microfiber Leather
Frame Material: Aluminum Alloy
Shifter Material: Aluminum Alloy
Size: 11 Inches
Buttons: 22 (Configurable)
LED Count (Strip): 10 LEDs
SmartTelemetry: Supported
MOZA Pit House Light Configuration: Supported
Quick Release: Supported
SR-P Lite Racing Pedals
Product Description
- High-strength Steel Pedals
- High Precision Hall Sensor
- Compatible with a variety of setups
- Adjustable Pedal Spacing
- Detachable Pedals
- Pedal Input Adjustable (Software)
Pedal Installation Process
-
Install the pedals onto the included footrest using the mounting holes. Use a 2.5mm hexagon wrench to fix the M410 screws into the footrest. To ensure stability and that the pedals will remain secure, it is recommended to use all four screws and install them firmly.
-
Connect the pedal wires to the corresponding included interface, using the wire clip under the pedal base to clamp the wires, preventing them from coming loose or interfer ing with product use.
-
Open the MOZA Pit House software suite to preview and confirm the status of each pedal.
f the device is still colored grey or does not respond after using the pedal, please unplug the base, close the MOZA Pit House, restart your PC, and reconnect the base, finally open the MOZA Pit House again. -
The pedal input (start, endpoint, stroke detail) can all be adjusted within the MOZA Pit House suite.
Pedal Spacing Adjustment
Select the relevant screw holes of the pedal you wish to adjust, loosen the
pedal, and move it either left of right to align the pedal as you wish,
tightening the screws to lock the pedal into place (adjusting the distance
between the throttle, brake and clutch is the same)
Plate Height Adjustment
Using a 2.5mm hexagon wrench, adjust the screws on the pedal board
counterclockwise, then use a 7mm open-end wrench to remove the back nut and
board screw. You may then move the board up and down to adjust the height
according to your needs, then screw the back nut and board screw back into
place. Adjustments to the throttle, brake, and clutch are done in the same
way.
Product Parameters
Pedal Material: High-strength Steel
Panel Material: High-strength Steel
Color: Black
Throttle Sensor: Hall Sensor
Pedal Spacing: Adjustable
Pedal Height: Adjustable
Pedal Input Adjustment: Software Supported
Pedal Reversible Function: Supported
Pedal Output Curve Adjustment: Software Supported
Anti-slip Pedal Bottom: Included
Packing List
- RS Direct Drive Wheelbase
- ES Racing Steering Wheel
- SR-P Lite Racing Pedals
- 15 Degree Desktop Mount
https://support.mozaracing.com/en/support/solutions/70000321076
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>