MOZA RACING SRP Racing Pedals User Manual
- June 9, 2024
- MOZA RACING
Table of Contents
MOZA RACING SRP Racing Pedals
Dear customer,
Thank you for purchasing our product. Please read the following instructions
carefully before first use and keep this user manual for future reference. Pay
particular attention to the safety instructions. If you have any questions or
comments about the device, please contact the customer line.
+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7,
www.alza.cz
Production introduction
- Made of high-strength steel
- High precision pressure sensor for up to 75 KG
- 16-bit high precision angle sensor
- Braking pressure sensor and angle sensor fusion algorithm
- Braking spring and damping block combined
- Adjustable pedal spacing Detachable pedal design
- Compatible with floor and professional cockpit
- Pedal travel software adjustment brackets
Pedal Instalment
- Place the pedals on the footrest, use a 2.5mm hexagon wrench to fix the M4*10 screws to the footrest. It is recommended that all 4 screws of each pedal are tightened to ensure stability.
- Connect the wires to the corresponding ports (the connecting wire of the clutch angle sensor needs to pass through the middle of the brake base, otherwise it may press on the wire harness after installing the pedal) and use the wire under the pedal base to clamp the wire harness to prevent the wiring harness is worn or tangled during intense driving.
- You will see the status of the SRP pedal in the Pit House once the wires are connected and the USB cable is plugged into the computer. (If it remains gray or does not respond, please unplug the USB port on the PC, turn off the MOZA Pit House, reconnect the USB port and turn on the MOZA Pit House)
- You could check the working status of the pedal, reset the pedal starting point, ending point, and pedal travel in the MOZA Pit House.
How to adjust the pedal spacing
Move left and right to adjust the spacing between the pedals and the base
holes, select the screw and then tighten the screw. (The accelerator, brake
and clutch are adjusted in the same way)
Instructions for adjusting the pedal board height
Use a 2.5mm hexagon wrench to turn the screws on the board surface of the
pedal counter clockwise and use a 7mm open-end wrench to remove the nuts on
the back and the screw on the board, move the board up and down to adjust the
height of the board according to your needs, and then fasten the nuts and
screws to the board surface. (The accelerator, brake and clutch are adjusted
in the same way)
Packing Details
- SRP Pedal
- Tool kit:
- M4*10 socket head countersunk head x12
- M8*12 hexagon socket head screw x3
- M6*20 socket head cap screws x2
- 2.5mm hexagon wrench x1
- 7mm open end wrench x1
- 5mm hexagon wrench x1
- Type A to Type B USB cable
Product Parameters
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:
- Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
- Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
- Natural wear and aging of consumables or components during use (such as batteries, etc.).
- Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
- If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.
EU Declaration of Conformity
Identification data of the manufacturer’s / importer’s authorized
representative: Importer: Alza.cz a.s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
CIN: 27082440
Subject of the declaration:
Title: Steering Wheel
Model / Type: Moza GS Steering Wheel
The above product has been tested in accordance with the standard(s) used to
demonstrate compliance with the essential requirements laid down in the
Directive(s):
Directive No. 2014/53/EU
Directive No. 2011/65/EU as amended 2015/863/EU
WEEE
This product must not be disposed of as normal household waste in accordance
with the EU Directive on Waste Electrical and Electronic Equipment (WEEE –
2012/19 / EU). Instead, it shall be returned to the place of purchase or
handed over to a public collection point for the recyclable waste. By ensuring
this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. Contact
your local authority or the nearest collection point for further details.
Improper disposal of this type of waste may result in fines in accordance with
national regulations.
References
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza.sk – rýchly a pohodlný nákup odkiaľkoľvek | alza.sk
- Alza | Alza.co.uk
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza.cz
- alza.de
- alza.hu
- alza.sk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>