MOZA RACING RS Series Steering Wheel User Manual

MOZA RACING RS Series Steering Wheel

Product Description

• Dual-Clutch Photoelectric Magnetic Paddles.
• RGB Programmable Flow Shift Light.
• Advanced Programmable Buttons and Knobs.
• D1 Style Quick Release.
• Wireless Technology.

How to Use the Quick Release OR Quick Release Setup

1. Aline the 6 steel balls on the steering wheel quick release female connector to the corresponding 6 grooves on the base quick release male connector.
2. Press the steering wheel down to join the connectors.
3. Once locked check to ensure the steering wheel is connected to base by rotating the wheel.
4. To remove the steering wheel, pull up the golden sleeve with both hands and remove the steering wheel at the same time.

Racing Wheel Configuration

The steering wheel can be set conveniently and quickly in the MOZA Pit House Software.

• Down paddle mode: Set the mode of double clutch paddles, which can be set as left and right composite axes, left and right independent axes and keys respectively.
• Speed follow-up: Turn on or off the linkage between LED shift indicator and speed.
• Indicator display mode: It is divided into mode 1 and mode 2. When the mouse moves over the option, a detailed explanation will pop up.
• Speed prompt setting: It is divided into advance type, standard type and limit type. according to the relationship between speed and the time when the shift indicator light is on.
• Color setting: 7 colors can be set separately for each LED.
• Brightness adjustment: Adjust the brightness of the shift indicator.
• Dial calibration: click here to calibrate the dial when the dial sensing is abnormal.

(for detailed steering wheel settings and functions, please visit the official website of MOZA Racing)

Installation of Paddle Approach Block

Use the hexagon wrench in the screw kit to remove the two screws on the shift paddle, add the heightening block, and tighten it with the attached long screw. Using this gasket, the distance between the paddle and the hand can be shortened by 8mm.

Installation of Magnetic Suction Paddle Mute Pad

Place the steering wheel on a flat surface with the surface facing down, use a hexagonal wrench to remove the screw on one side of the shift paddle trigger rod, and then use a wrench to push the pin from the side of the magnetic suction paddle (it is not necessary to push the pin out completely, only to separate the magnetic suction paddle trigger rod and the pin), and then stick the mute pad on the convex position on the back of the paddle trigger rod, as shown in the figure. Finally, return the latch, and replace the screw.

For more information and teaching videos, please log in to the official website.

Packing List

1. RS steering wheel
2. tool kit:
   • Hexagon screwdriver
   • M3x14 screw x8
   • 8mm aluminum alloy approach block x4
   • Mute pad x4

Product Spec

• Frame material: Brushed aluminum alloy. Panel material: Forged Carbon Fiber.
• Rear shell material: Aluminum alloy.
• Paddle material: 3mm thick forged carbon fiber Size: 13 inches (325mm).
• Magnetic paddle: 2.
• Double-clutch paddles: 2.
• Mechanical keyboard texture keys: 10.
• 20 Section knob (can be pressed): 2. Universal rocker (can be depressed): 2. Racing horn: 1.
• Highlight led RGB beads: 10.
• LED color: 7-color custom.
• Intelligent telemetry: Supported.
• Lights setting via Moza Pit House:
• Supported.
• Steering Wheel Quick Release: D1 racing quick release.
• Power supply mode: Wireless. Signal transmission mode:
• Wireless. Induction mode of magnetic paddle: Photoelectric.
• Magnetic suction paddle mode: Double Clutch / Single Clutch / Switch.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

References

• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.sk – rýchly a pohodlný nákup odkiaľkoľvek | alza.sk
• Alza | Alza.co.uk
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz
• alza.de
• alza.hu
• alza.sk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>