NUX NBP-5 Melvin Lee Davis Bass Preamp + DI Owner’s Manual
- June 6, 2024
- NUX
Table of Contents
NUX NBP-5 Melvin Lee Davis Bass Preamp + DI
Copyright
Copyright 2019 Cherub Technology Co. All rights reserved. NUX and Melvin Lee
Davis Bass Preamp & DI are trademarks of Cherub Technology Co. Other product
names modeled in this product are trademarks of their respective companies
that do not endorse and are not associated or affiliated with Cherub
Technology Co.
Accuracy
Whilst every effort has been made to ensure the accuracy and content of this
manual, Cherub Technology Co. makes no representations or warranties regarding
the contents.
WARNING! IMPORTANT SAFETY INSTRUCTIONS BEFORE CONNECTING, READ INSTRUCTIONS
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: To reduce the risk of fire or electric shock, do not remove screws. No user-serviceable parts inside. Refer servicing to qualified service personnel.
CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING:
The lightning symbol within a triangle means “electrical caution!” It
indicates the presence of information about operating voltage and potential
risks of electrical shock.
WARNING:
The exclamation point within a triangle means “caution!” Please read the
information next to all caution signs.
- Use only the supplied power supply or power cord. If you are not sure of the type of power available, consult your dealer.
- Do not place near heat sources, such as radiators, heat registers, or appliances which produce heat.
- Guard against objects or liquids entering the enclosure.
- Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
- Servicing is required when the apparatus has been damaged in any way, such as when the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped.
- The power supply cord should be unplugged when the unit is to be unused for long periods of time.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and at the point where they exit from the apparatus.
- Prolonged listening at high volume levels may cause irreparable hearing loss and/or damage. Always be sure to practice “safe listening”.
Follow all instructions and heed all warnings KEEP THESE INSTRUCTIONS!
Overview
Melvin Lee Davis Bass Preamp & DI
We collaborated with American bass player (also vocalist, keyboard player, TV
composer, engineer) Melvin Lee Davis to create MLD Bass Preamp & DI. It has
tons of functions based on Melvin Lee’s musical experience, and offers the
best sound shaping controls such as 3-band EQ with middle-frequency selection,
drive with blend control, speaker cabinet simulation (Impulse Response file
loader) and built-in noise gate with decay and threshold controls.
Audio Streaming and Recording
MLD Bass Preamp + DI can also be used as an audio interface. You can download
and install the free NUX ASIO Driver, connect the pedal to your computer via
USB, use the headphone output on the pedal for monitoring, then it can send
the bass guitar audio signal for recording. Simply you don’t have to use any
other output on the pedal or computer.
NBP-5 Edit Software
You can control the pedal with the software and also load/change Impulse
Response files. Visit nuxefx.com and download the software for free.
Features:
- 3-band EQ with Middle-frequency selector
- Drive with blend control
- Built-in noise gate
- Impulse Response loader, speaker cabinet simulation
- Versatile input and output options
- Firmware updates, software control, audio stream
Control Panel
Control Panel
-
VOLUME knob
Adjusts the output volume. -
BLEND knob
Adjusts overdrive signal mix with the dry signal between 50% and 100%. -
DRIVE knob
Adjusts the overdrive level (can be activated with DRIVE footswitch). -
BASS knob
Adjusts the low frequency level. -
MIDDLE knob
Adjusts the selected middle frequency level. -
FREQ knob
Middle frequency selector. You can choose from low mid 160Hz to high mid 1kHz. According to different amp models, the EQ range and response are different. -
TREBLE knob
Adjusts the high frequency level. -
DI toggle
Activates the Impulse Response speaker cabinet simulation for DI out and the headphone out. -
OUT toggle
Activates the Impulse Response speaker cabinet simulation for main output. -
**Preamp Foot Switch
Engages / disengages the preamp.
**
- Drive Foot Switch
Engages / disengages the overdrive.
Noise Gate: Push and hold the Drive footswitch for 1.5 seconds, the green LED light will start to blink. Now you can control the noise gate Decay by Blend knob, and Gate Threshold by Drive knob. When you turn the Threshold to 0, noise gate will be OFF.
Decay: Adjusts the speed of the noise gate.
Threshold: Adjusts the gate level.
Hold the Drive footswitch for 1.5 seconds again to go back to use the pedal. Green LED will stop blinking.
I/O Jacks
-
1/4″ Mono Jack Input
Instrument input. -
Input to DI Signal Routing Toggle
If you want to use the DI out without using the preamp, you can set the toggle
to PRE. The input signal will be delivered to DI output directly.
Or you can set the toggle to POST to use the preamp and drive functions for DI
out connection. No matter the PRE or the POST is selected, you can
activate/deactivate the speaker cabinet simulation using the DI Toggle.
- **Ground Lift Toggle
**
If you meet ground loop noise issue, it helps you to eliminate the hum noise.
-
1/4″ Through Output
Dry signal output, if you want to connect the pedal to the amplifier in front. You can avoid the pedal’s preamp section and use the amplifier’s preamp. Speaker cabinet simulation is not supported. -
1/4″ Main Output
The main output. You can get the processed sound from preamp/drive section. Speaker cabinet simulation can be activated/ deactivated. -
Micro B USB
You can connect to the computer for updates, software control and audio streaming. -
Power Input
Negative tip power cable input 9V -
1/8” Auxiliary Input
You can connect music player to play along with music. -
1/8” Headphone Output
For silent practicing or monitoring. -
**XLR DI Output
**
For direct connection to mixer (or PA system).
You can use the PRE/POST Toggle to run the pedal’s preamp/drive section or you
can send the dry signal directly.
Also speaker cabinet simulation can be activated/deactivated.
Connecting Audio Equipment
Specifications
-
Sampling Frequency: 48kHz
-
A/D Converter: 32bit
-
Signal Processing: 32bit
-
Frequency Response Range: 20Hz ~ 20kHz
-
Noise Level: -93dBu (A-Weighted)
-
Dynamic Range: 100dB
-
EQ:
MLD – Bass ±12dB @ 40Hz
Middle ±17dB @ 160Hz ~ 1kHz Treble ±12dB @ 8kHz
AGL – Bass ±18dB @ 40Hz
Middle ±17dB @ 180Hz ~ 1kHz Treble ±18dB @ 4kHz -
Current Draw: <150mA
-
Power Supply: 9V DC, Negative Tip (Optional ACD-006A Adaptor)
-
Dimensions: 105mm(L) x 115mm(W) x 58mm(H)
-
Weight: 460g
Accessories: User manual
*Specifications and features are subject to change without notice.
MADE IN CHINA
Documents / Resources
| NUX
NBP-5 Melvin Lee Davis Bass Preamp +
DI
[pdf] Owner's Manual
NBP-5, Melvin Lee Davis Bass Preamp DI, NBP-5 Melvin Lee Davis Bass Preamp DI,
Bass Preamp DI, Preamp DI
---|---