HGLRC Veyron3 HD FPV Racing Drone User Manual

HGLRC Veyron3 HD FPV Racing Drone User Manual

Product Specifications

Product parameters

Model

| Veyron3 HD

FPV Racing Drone

Weight

| 267.0g(BNF)

266.0g (PNP)

Frame Kit| Veyron3   Frame Kit
Flight Controller| Zeus35 AIO
ESC| 35A 4in1
VTX| CaddxVista
Camera| DJIFPVCamera

Motor

| FD1408

kv2400（6S） KV3600（4S）

Support receiver| SBUS .DSMX.i.BUS
Input Voltage| 3-6S Lipo
Size| 205X188mm

Interface Description

Check the flight control drive

1. Long Press BOOT buttons. connect USB. The system automatically install the driver
   

2. Driver cannot be installed, please download ImpulseRC_Driver_Fixer

3. Double-click on the run(Plug in the flight controller to automatically install the driver)
   

4. open betaflight configurator ，enter DFU mode
   

5. Click Select firmware version
   

6. Click Load firmware. Waiting for completion It will be prompted upon completion.

7. open betaflight configurator 。Controller plugged into the computer. Betaflight Automatically assigned port，click “Connect” Enter setup interface（Different computer COM）

Calibration accelerometer

1. Put the aircraft horizontal and click“Reset Z axis” Click again
   

URAT serial port use

• URAT1 uses VTX image transmission
• UART2 uses receiver telemetry

Select aircraft model

1. Click Select model
   

2. Click Click “I understand the risks”Push Master to check motor steering“Master”Steering can be changed at BLHeliSuite
   

Choose ESC protocol

1. Choose the right ESC protocol, the optional universal protocol DSHOT600.
   

Voltage parameters setting

1. Click Power & Battery Setting parameters
   

Setting up the receiver

1. Receiver connection diagram
   

2. Click .have found“UART2”Open （SBUS） the receiver serial port
   

3. Open (i.BUS/DSMX) receiver serial port
   

4. Set the SBUS receiver
   

5. Set the i.BUS receiver
   

6. Set the DSMX receiver
   

VTX serial port use. VTX uses OSD smart audio

1. VTX connection diagram
   

2. VTX serial port opens. The protocol is selected according to its own VTX protocol.

Check receiver signal

1. Click Check the remote control output signal
   

Select flight mode startup mode

Click set up the function of remote control switch across the channel (below are for reference only)

LED settings

Click Turn on LED support

Click LED Strip .Click wire ordering mode set according to need

Troubleshooting
Warning: Please read the cautions as follows, otherwise stability of your flight controller cannot be ensured, your flight controller will even get damaged.

• Keep focus on the polarity. Check carefully before power supply.
• Cut off the power when you connect, plug and pull anything.
• The refresh rate of PID and Gyroscope is up to 8K/8K.

after-sales question:

1. After receiving the goods, it is found that the product can not be used normally. If the return to the factory is a quality problem, the repair service will be provided free of charge.
2. If the product is damaged due to improper operation, the repair service may be provided under the condition that the inspection can be repaired.
3. For domestic customers, please contact the after-sales service personnel. For overseas customers, please contact the official website for after-sales service.

Product daily problems

1. When plugged in the battery, the aircraft does not pass the self-test without “BBB” sound. There is only one sound.
   Please check if the ESC agreement is correct

2. The spin of the aircraft keeps spinning

   • Please check if the propeller is correct
   • Please check if the motor direction is correct

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>