ARROW 4 In 1 Pneumatic 18 Gauge Flooring Stapler Nailer Instruction Manual

4 In 1 Pneumatic 18 Gauge Flooring Stapler Nailers
Instruction Manual

4 In 1 Pneumatic 18 Gauge Flooring Stapler Nailer

Caution: Please read the manual carefully.
Misuse of this product could cause property or equipment damage and/ or personal injury.
To avoid injury and misuse, please read the instruction manual before operation.
 Comply with all safety messages marked with this symbol to avoid possible injury or death.
To avoid loss of hearing, always wear ear protection when operating the tool.
To avoid eye injury always wear safety glasses when operating the tool.
3 YEAR LIMITED WARRANTY
Arrow Fastener Company warrants to the original consumer purchaser (“you”) that this product will be free from original defects in materials and workmanship for 3 years after you purchase it. If the product does not comply with this warranty, Arrow will, at its option, repair or replace the product with an equivalent product at no charge to you. This warranty is not transferable. For best perfor­mance, use genuine Arrow nails. Arrow nails are made to exact tolerances to ensure trouble-free  performance. This warranty does not cover defect or damage to the extent caused by the use of non Arrow branded nails. This warranty also does not cover damage relating to normal wear and tear, misuse, abuse, neglect, accident, natural disaster, or alteration of the product without Arrow’s consent.
TO THE EXTENT PERMITTED BY LAW, ANY IMPLIED WARRANTIES, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE SAME DURATION AS THIS EXPRESS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
NO OTHER EXPRESS WARRANTY HAS BEEN MADE OR WILL BE MADE BY ARROW WITH RE­ SPECT TO THIS PRODUCT. ARROW SHALL NOT BE RESPONSIBLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion of incidental or consequential damages so the above exclu­sion and limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from state to state. This guarantee does not affect your statutory rights. In Canada, the above provisions are not intended to operate where prohibited by law and do not preclude the operation of any applicable provincial consumer protection statute which may in certain circumstances extend the express warranty herein. To obtain the benefits of this warranty, you must send contact.
Please contact Arrow Fastener by calling
1-800-776-2228 or by writing: Arrow Fastener Company, LLC
271 Mayhill Street Saddle Brook, NJ 07 663
Attn: Product Warranty Department.

TECHNICAL DATA

GENERAL SAFETY RULES

1. KEEP CHILDREN, VISITORS AND BYSTANDERS AWAY FROM TOOL. Distractions can cause misuse and possible loss of control. When tool is not operational, it should be locked in a safe place out of the reach of children.
2. USE SAFETY GLASSES AND EAR PROTECTION: Air tool operators and others in work area should always wear safety glasses and ear protection to prevent injury from flying debris as well as possible hearing damage.
3.  NEVER USE OXYGEN, COMBUSTIBLE OR ANY OTHER BOTTLED GAS as a power source or it can cause an explosion and serious personal injury. (See fig 2.)
4.  DO NOT CONNECT TOOL TO COMPRESSED AIR THAT EXCEEDS 120PSI.
5. MAKE SURE HOSE IS FREE OF ANY OBSTRUCTIONS OR SNAGS. Entangled hoses can cause loss of balance or footing.
6.  KEEP THE TOOL POINTED AWAY FROM YOURSELF and others at all times and keep hands, any body parts away from rear area to safety guard against possible injury.
7.  DISCONNECT TOOL FROM AIR SUPPLY BEFORE LOADING FASTENERS to prevent accidental firing during connection.
8.  DO NOT KEEP THE TRIGGER OR SAFETY DEPRESSED WHEN LOADING STAPLES. This can cause unintentional firing and accidental injury may occur.
9. DISCONNECT TOOL FROM AIR SUPPLY HOSE and close the compressor before perform­ ing maintenance and during non-operation.
10. DO NOT OVERREACH DURING USAGE. Maintain proper footing at all times to avoid loss of balance and possible injury.
11.  DO NOT DRIVE FASTENERS CLOSE TO THE EDGE OF THE MATERIAL. This can cause the workpiece to potentially split resulting in fasteners ricocheting causing injury to you or your coworkers.
12. DO NOT DRIVE FASTENER ON TOP OF NAILED FASTENERS, or the fasteners can ricochet causing personal injury.
13.  NEVER USE A TOOL THAT IS LEAKING AIR, HAS MISSING OR DAMAGED PARTS OR REQUIRES REPAIR. and make sure all the screws are securely tightened.
14. ALWAYS OPERATE TOOL IN CLEAN WELL LIT AREAS. Be sure the work area is clear of any debris.
15.  ONLY USE PARTS AND ACCESSORIES recommend by manufacturer.
16. BE AWARE OF MATERIAL THICKNESS DURING USE. A protruding nail can cause injury.
17. DO NOT DRIVE NAILS BLINDLY INTO SURFACES. Be aware of pos­sible electrical wires, plumbing or other types of obstructions that can cause injury or damage.

WARNING!
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproduc­tive harm. Some examples of these chemicals are:

• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Use of this tool can generate and/ or disburse dust, which may cause serious and permanent respira­tory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. Always operate tool in well-ventilated area and provide for proper dust removal. Use dust collection system wherever possible.

OPERATING INSTRUCTIONS

APPLICATIONS
Including, but not limited to: insulation, roofing felt, house wrap, auto and marine vinyl trim, cabinet felt, cabinet backs, screen door repair, small furniture, light trim, molding and picture frames, and general staple use.
Bump Fire Action
Bump fire action is intended for rapid firing of nails on flat stationary surfaces and usually is most effective with shorter brad nails. Typical applications for this include attaching baseboard, trim work, wood working, and general purpose applications. Bump fire actuation can be used for multiple actuations or easier single actuations. Multiple Actuations: (Not applicable as flooring nailer}

1. Grip the handle securely.
2.  Depress the trigger.
3.  Push the contact safety tip against the workpiece to fire.
4.  Continue to hold the trigger and repeat contacts with the workpiece to fire.

Single Actuation:

1. Grip the handle securely.
2.  Depress the trigger.
3. Push the contact safety tip against the workpiece to fire.
4. Remove your finger from the trigger and remove the tool from the workpiece.

ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool allows users to direct the exhaust according to operator preference. To adjust the direction, turn the exhaust cap in the desired direction.
DESCRIPTION
Arrow’s PT4-1 4-in- 1 18Ga Mini Flooring Nailers & Stapler drives 18Ga brad nails from 5/8″ to 2″(15mm to 50mm) and narrow staples from 3/4″ to 1-9/16″(19mm to 40mm) in length. The tool has a die cast aluminum body for strong and light weight design. The tool features a comfortable rubber handle for improved control and comfort even during extended use and a contact safety to prevent accidental firing and a quick release nosepiece for fast clearing of jams. The tool is ideal for door and window trims, decorative trim, and cabinet work, finish paneling, frames, and flooring.
18GA BRAD NAILS

18GA NARROW STAPLES

AIR SUPPLY

1. Use clean, Dry and Regulated compressed air at 60-100PSI(4-7bar)
2. Never exceed maximum and minimum pressure. Too low or too high pressure would cause noise wear and tear or misfiring.
3.  When connecting air supply always keep hands and body away from discharge area of tool.
4. A filter-regulator-lubrication is required and should be located as close to tool as possible.
5.  Keep air filter clean. A dirty filter will reduce the air pressure to the tool causing a reduction in power and efficiency.
6.  For better performance, install a quick connector in your tool and quick coupler on the hose if possible.
7.  Be sure all connections in air supply system are sealed to prevent air loss.

LOADING AND OPERATION
WARNING!
Always disconnect the tool from the compressed air before loading. When loading the tool always keep the tool pointed away from yourself and others. Make sure that you are not holding the tool with trigger depressed while loading to prevent accidental firing. TURN IT INTO A BRAD NAILER/STAPLER
The tool can be changed to a regular brad nailery/stapler when the base assembly is removed. FLOORING BASE ADJUSTMENT
When the base is set on the nailery, the floor plate depth is adjustable for 3/8, 5/8″ and 1 /2″ thick floor wood.
To adjust the base depth, please follow the step as listed below: Press the button first, then move the base to the appropriate position and release the button. NO-MARRING PAD
The tool also has a no-marring pad at the end of the magazine, which is used as a regular brad nailery/ stapler.
The no-marring pad attached to the nose of the tool helps prevent marring and denting when work­ing with finished surfaces. CLEARING JAMS
Occasionally, a fastener may become jammed in the firing mechanism of the tool, making the tool inoperable. To remove a jammed fastener, follow these steps;

1. Disconnect the tool from air resource,Remove the nails from the magazine.
2. Pull up on the lunch and open the flooring nose cover.
3.  Remove fasteners from the tool. Failure to do so will cause the fasteners to eject from the front of the tool.
4.  Push the latch back to the nose cover on the mailer’s nose.

WARNING!
Disconnect the tool from the air compressor before adjusting, clearing jams, ser­vicing, relocating and during non-operation.

• Check and change all worn or damaged orings, seals, etc. Tighten all the screws and caps to avoid personal injury.
• Inspect trigger and safety mechanism to assure system is complete and functional with no loose or missing parts.
• Keep magazine and nose of tool clean and free of any dirt lint or abrasive particles.

PT4-1 SCHEMATICS & PARTS LIST

PART| DESCRIPTION| QTY| PART| DESCRIPTION| QTY| PART| DESCRIPTION| QTY| PART| DESCRIPTION| QTY| PART| DESCRIPTION| QTY
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
1| Hex Bolt M4X12| 4| 16| 0-ring 20.3X2.62| 1| 31| Safety Tip Guide| 1| 46| Drive Guide| 1| 61| Limited Nail Plate| 1
2| Bush| 1| 17| Firing Pin| 1| 32| Spring Pin 3X26| 2| 47| Safety Sleeve| 1| 62| Base| 1
3| Exhaust Deflector| 1| 18| Cylinder| 1| 33| Spring Pin 2.5X18| 1| 48| Pin 1.5X15| 1| 63| Spring Pin 3X16| 1
4| Hex Bolt M5X35| 1| 19| 0-ring 43.3X2.5| 1| 34| Trigger Plate| 1| 49| Fixed Magzine| 1| 64| Spring| 1
5| Washer 5| 6| 20| 0-ring 28X1.8| 1| 35| Pin 3X26| 1| 50| Fillet| 1| 65| Tooth Piece| 1
6| 0-ring 7.8X1.9| 1| 21| Bumper| 1| 36| 0-ring 1.2X1.9| 1| 51| Hoder| 1| 66| Button| 1
7| Cylinder Cover| 1| 22| Body| 1| 37| Trigger| 1| 52| Hex Bolt M4X6| 3| 67| Mobil Magazine| 1
8| Shim| 1| 23| Rubber Grip| 1| 38| Hex Bolt M5X10| 1| 53| 0-ring 1.2X1.9| 3| 68| Pusher| 1
9| Gasket| 1| 24| 0-ring 31.3X3.5| 1| 39| Spring Pin 3X22| 1| 54| Drive Guide Cover| 1| 69| Spring| 2
10| 0-ring 13.6X2.4| 1| 25| End Cap component| 1| 40| Click Fixer| 1| 55| Plate| 1| 70| No-mar Pad| 1
11| Compression Spring| 1| 26| Plug Cap| 1| 41| Compression Spring| 1| 56| Pin 3X18| 1| 71| Magazine End Stopper| 1
12| Head Valve| 1| 27| Nozzle| 1| 42| Hex Bolt M4X8| 1| 57| Quick Release latch| 1| 72| Hex Bolt M4X10| 1
13| Seal| 1| 28| Spring| 1| 43| Safety| 1| 58| Washer| 1| | |
14| 0-ring 31.3X2.5| 1| 29| Switch components| 1| 44| Hex Bolt M5X25| 2| 59| Pin 3X21| 1| | |
15| Retaining Ring| 1| 30| Spring| 1| 45| Hex Bolt M4X14| 2| 60| Spring pin 2.5X30| 1| | |

Arrow Fastener Company, LLC
271 Mayhill Street
Saddle Brook, New Jersey 07663 USA
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>