Xblitz Uni Pro 3 Wireless Earbuds User Manual

Xblitz Uni Pro 3 Wireless Earbuds

Thank you for purchasing the Xblitz UNI PRO 3
wireless earphones set. Please read the attached instructions and safety measures before using the device.

SAFETY MEASURES

To use the earphone set correctly and safely, read the instructions below. When using the set, follow the following rules:

1. Adjust the volume when using the earphone set correctly.
2. In a situation of emergency, stop using the set to ensure your safety.
3. Do not use the set to listen to music, make or receive calls while driving a car.
4. Put the product, together with accessories, in a place inaccessible for children to avoid the danger caused by improper use.
5. Prevent water from entering the Earphones during cleaning, as this can cause sound distortion and even lead to damaging the set.
6. Avoid setting the volume too high, i.e. to the levels that make if impossible to hear anything around you. If you hear a buzzing noise in your ears or feel that the volume is too high, you should immediately reduce the volume.
7. Stop using the set if there is pronounced discomfort, irritation or other unwanted reactions.
8. In case of excessive overheating headphones, stop using immediately and contact an Authorized Service Center.

MAIN FEATURES

1. Ability to wirelessly play music from your phone.
2. Ability to make wireless phone calls.
3. Handy earphone charging case.
4. Voice messages in English that indicate the status of batteries, incoming connections, disconnecting the device, etc.

PACKAGE CONTENTS

1. Earphones
2. Charging case
3. USB cable (charging)
4. User’s manual
5. 2 sets of spare rubber tips

GETTING STARTED

PAIRING THE DEVICE

1. Remove the insulation tape from the earphones and reinsert them into the charging case to charge both earphones.
   WARNING: If the set does not charge when placed in the case, please connect the USB power cord to the power port of the case.

2. After taking the earphones out of the case (markings indicating which ear each earphone fits into can be found on the device itself. R- right ear, L – left ear), a blue LED should flash on both of them, indicating that the device has turned on.

3. If the earphone LEDs are alternating between blue and red, the device is ready to pair. Turn on BT connectivity on your phone and on the list of available devices
   to connect to your phone, select Xblitz UNI PRO 3.
   When the headphones are paired with the phone, the LEDs on them will stop blinking and the corresponding information (e.g. “The device is connected, 100% battery left”) will be displayed on your phone.

4. The earphones will automatically turn o when they are inserted into the case. The device will also automatically turn o after 300 seconds of inactivity.

5. Taking the earphones out of the case again will automatically turn them on and pair them again with your phone.
   WARNING: If pairing fails, restore the device to factory settings. To do this, turn o the earphones and then hold the buttons on both of them for 8 seconds. Then turn on the device, the set should pair up automatically.

BUTTON FUNCTIONS

1. Turn on/ o – holding the button of any of the earphones for 3 seconds turns the device on/o . The blue LED indicates that the device turned on, red – o .
2. Play/Stop – briefly press any of the earphone buttons to turn music playback on/o .
3. Answer/ End phone call – press the button on any earphone to answer a phone call or end the call.
4. Reject a call – hold the button for 2 seconds to reject the incoming call.
5. Redial number – double-press the button on the left earphone to connect to the last dialed number.
6. Change track – double-press the button on the right earphone to change the song played to the next one.

SINGLE EARPHONE MODE

You can connect to your phone using only one earphone, leaving the additional earphone in the charging case.
The earphone will automatically connect to the phone with which the set is paired.
If you want to switch from using one earphone to using both – remove the other earphone from the case. Both earphones should automatically connect to the paired phone.

CHARGING

To charge the earphones, place them in the case. Magnets placed in the case should keep the earphones in place.
If charging starts successfully, red LEDs on the earphones will turn on, as well as a blue LED on the case. When the LEDs turn o , the charging is complete.
To charge the battery of the case, connect it to power using a regular 5V charger with a micro USB cable. When the case is connected to power, the blue LED on it will blink.

SPECIFICATIONS

• Impedance of earphone speakers: 16 ohm
• Operating frequency: 24.0Hz ~ 20KHz
• BT version:  5.0
• Talk/listening time (average volume):  3-4h
• Standby mode time:  96h
• Connection range:  10m
• Earphone sensitivity:  88dB
• Earphone power:  3mW
• Charging time (headphones and case): 1-2h
• Earphone battery capacity:  40mAh
• Case battery capacity:  400mAh
• Battery voltage:  3.7V
• DC in:  5V
• Dimensions (case):  67x40x29mm
• Weight (with case):  39g

WARRANTY CARD/ COMPLAINTS

The product is covered by a 24-month warranty.
The terms of the guarantee can be found at:
https://xblitz.pl/warranty/
Complaints should be reported using the complaint form located at: http://reklamacje.kgktrade.pl/
Details, contact and website address can be found at: www.xblitz.pl
Specifications and contents of the kit are subject to change without notice. We apologise for any inconvenience.
KGK Trade declares that this device XBLITZ UNI PRO 3 is compliant with significant requirements of directive 2014/53/EU.
The text of this declaration may be found on the website:
http://xblitz.pl/download/DOC/deklaracja-CE-Xblitz-uni-pro3.pdf
Manufacturer:
KGK Trade sp. z o.o. sp. k.
Os. Urocze 12
31-953 Cracow
Poland
Made in P.R.C.

References

• System reklamacyjny KGK Trend
• Warranty - Xblitz.pl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>