SILVERSTONE RMS08 Series RMS08-20 High Quality Tool-Less Ball Bearing Sliding Rail Kit User Manual

June 4, 2024
SilverStone

SILVERSTONE RMS08 Series RMS08-20 High-Quality Tool-Less Ball Bearing

Sliding Rail Kit

The Tool-less server slide is designed and built for 1U and 2U chassis. The bracket can be mounted on an EIA rackmount – bracket with a 5/8” pitch, suitable for square holes.

Installation

Step 1 – Install the slide members to each side of the cabinet:
The inner member of the server slide needs to be taken out and assembled with chassis. The middle member / outer member is installed on the rackmount to be ready for Step 5.
Step 2 – Remove the inner member:
Pull the inner member out to the locking point. Then press the trigger down as shown on Figure-1, and fully pull out the inner member to facilitate the installation of the chassis.
Step 3 – Mount the inner member to the chassis:
Assemble the inner members to the chassis with M4 screws from the screw kit.
Step 4 – Install the middle member / outer member on the rack mount:
Insert the middle member / outer member of the servers and slide into the upper and lower square holes of the EIA rack mount from inside the cabinet.

Optional Step (but Suggested):

After the installation is finished, you may fix it with a screw (M5x15) into the center of the cabinet hole.

The rackmount ear pieces which are assembled to the chassis are suggested to have a bottom hole in order to avoid restricting the function of the blue knob on the server slide.

Step 5 – Mount the chassis into the cabinet:
Insert the assembled chassis into the cabinet member as shown in the drawing below. It is important to check if the ball cage is in a fully open position before installing the chassis (Figure-2). It might cause catastrophic damage to the chassis if the ball cage is not in the fully open position while mounting the chassis. While you are pushing the chassis back to the cabinet, you need to release the slide from the locking position by pressing the trigger down (Figure-3). A critical step is – Make sure the chassis is pushing to the utmost end and complete it as “Reset”

Dismount

Step 1 – Release the rail from the rackmount bracket:
Push the half-moon shape area to get easy release.

Warranty Information

This product has a limited 1-year warranty in North America and Australia. For information on warranty periods in other regions, please contact your reseller or SilverStone authorized distributor.

Warranty terms & conditions 

  1. Product component defects or damages resulting from defective production is covered under warranty. Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology’s jurisdiction.
    • Usage in accordance with instructions provided in this manual, with no misuse, overuse, or other inappropriate actions.
    • Damage not caused by natural disaster (thunder, fire, earthquake, flood, salt, wind, insect, animals, etc…)
    • The product is not disassembled, modified, or fixed. Components are not disassembled or replaced.
    • Warranty marks/stickers are not removed or broken. Loss or damages resulting from conditions other than the ones listed above are not covered under warranty.
  2. Under warranty, SilverStone Technology’s maximum liability is limited to the current market value for the product (depreciated value, excluding shipping, handling, and other fees). SilverStone Technology is not responsible for other damages or losses associated with the use of the product.
  3. Under warranty, SilverStone Technology is obligated to repair or replace its defective products. Under no circumstances will SilverStone Technology be liable for damages in connection with the sale, purchase, or use including but not limited to loss of data, loss of business, loss of profits, loss of use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty, contract or negligence, even if SilverStone Technology has been advised of the possibility of such damages.
  4. Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable to a second-hand purchaser.
  5. You must provide a sales receipt or invoice with a clear indication of the purchase date to determine warranty eligibility.
  6. If a problem develops during the warranty period, please contact your retailer/reseller/SilverStone authorized distributors or SilverStone http://www.silverstonetek.com. Please note that:
    • You must provide proof of original purchase of the product by a dated itemized receipt;
    • You shall bear the cost of shipping (or otherwise transporting) the product to SilverStone authorized distributors. SilverStone authorized distributors will bear the cost of shipping (or otherwise transporting) the product back to you after completing the warranty service;
    • Before you send the product, you must be issued a Return Merchandise Authorization (“RMA”) number from SilverStone. Updated warranty information will be posted on SilverStone’s official website. Please visit http://www.silverstonetek.com for the latest updates.

Additional Info & Contacts

For North America (usasupport@silverstonetek.com)
SilverStone Technology in North America may repair or replace the defective product with a refurbished product that is not new but has been functionally tested. A replacement product will be warranted for the remainder of the warranty period or thirty days, whichever is longer. All products should be sent back to the place of purchase if it is within 30 days of purchase, after 30 days, customers need to initiate the RMA procedure with SilverStone Technology in the USA by first downloading the “USA RMA form for end-users” form from the below link and follow its instructions. http://silverstonetek.com/contactus.php
For Australia only (support@silverstonetek.com)
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please refer to the above “Warranty terms & conditions” for further warranty details. SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan R.O.C. + 886-2-8228-1238 (standard international call charges apply)
For Europe (support.eu@silverstonetek.de)
For China (support@silverstonetek.com.cn)
For all other regions (support@silverstonetek.com)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SilverStone User Manuals

Related Manuals