SILVERSTONE RM47-502I 4U Interchangeable Rackmount Chassis User Manual

June 1, 2024
SilverStone

SILVERSTONE-logo

SILVERSTONE RM47-502I 4U Interchangeable Rackmount Chassis

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
product

Specifications

  • Compatible with full-height expansion cards
  • Supports horizontal orientation installation for graphics cards
  • Includes various accessories for installation
  • Riser cable holder and CPU cooler compatibility
  • PSU mount and 5.25 drive cage interchangeability

Product Usage Instructions

Full-height Expansion Card Installation:

  1. Remove both the expansion card holder and the riser cable holder.
  2. Unfasten and remove the 4 screws securing the horizontal expansion card module.
  3. Remove the horizontal expansion card module.

Full-height Graphics Card in Horizontal Orientation Installation:

  1. Remove the PCI slots.
  2. Install the graphics card onto the horizontal expansion card module.

Adjusting Expansion Card Holder and Module

  1. Place the graphics card into the expansion card holder.
  2. Install the graphics card, expansion card module, and expansion card holder into the chassis.
  3. Secure the components back into the chassis at different adjustment positions.

Riser Cable Installation:

  1. Attach the riser cable to the riser cable bracket and secure it with screws.
  2. Connect the riser cable to the motherboard and graphics card, then secure the whole module with screws.

PSU Mount and Drive Cage Interchangeability:

  1. Remove both the expansion card holder and the riser cable holder.
  2. Adjust the positions of the drive cage and PSU mounting bracket as needed for installation.

FAQ

  • Q: What are the maximum heights for CPU coolers with and without the riser cable holder?
    A: Maximum height with riser cable holder: 114mm; Maximum height without riser cable holder: 148mm.

  • Q: What components can be installed in the 5.25 drive cage?
    A: You can install a 5.25 ODD, a 3.5 HDD, or 2.5 SSD drives in the 5.25 drive cage.

RM47-502I
User manual
www.silverstonetek.com

Accessories Content

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(1\)

Full-height expansion card installation

  • Remove both expansion card holder and the riser cable holder
  • Unfasten and remove the 4 screws securing the horizontal expansion card module
  • Remove the horizontal expansion card module
  • SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis- \(2\)

Full-height graphics card in horizontal orientation installation

  • Remove the PCI slots
  • Install the graphics card onto the horizontal expansion card module

Secure the graphics card, expansion card module, and expansion card holder back into the chassis

  • First, place the graphics card into the expansion card holder, then install the graphics card, expansion card module and expansion card holder into the chassis
  • Secure the expansion card module with screws at the front chassis, and secure the expansion card holder with screws on both sides of the chassis

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(5\) Different adjustment positions for the expansions card holder

Adjusting the expansion card holder

Fixating the riser card holder

  • Place the rubber dampening padding under the graphics card and double check the padding does not interfere with the graphics card cooling fans
  • Remove the riser cable holder first before installing the riser cable
  • Attach the riser cable to the riser cable bracket and secure with screws (Optional SST-RC05 PCIe Gen 5 riser cable can be purchased)

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(7\) SILVERSTONE-RM47-502I-4U-
Interchangeable-Rackmount-Chassis- \(8\)Connect the riser cable to the motherboard and graphics card then secure the whole module with screws

Riser cable holder and CPU cooler compatibility

CPU Cooler
Maximum height with riser cable holder: 114mm
Maximum height without riser cable holder: 148mm

PSU mount and 5.25” drive cage interchangeability instructions

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(11\)

  • Removal of PSU mounting bracket
    Unfasten and remove the PSU mounting bracket screws

  • Remove the PSU mounting bracket from the rear chassis panel

  • Remove the bottom PSU mounting bracket screws located at outer side of the bottom chassis

  • Remove the bottom PSU mounting bracket located at the bottom of the chassis

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(12\) 5.25” drive cage removal
Unfasten and remove the 4 screws on the side securing the drive cage

PSU mount and 5.25” drive cage interchangeability instructions

Adjust the 5.25” drive cage position to the rear, and the PSU mounting bracket to the front
Secure the corresponding screws

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(14\)

Installation of components in the 5.25” drive cage

Installing conductive foam to fill the gaps on the drive cage Installing 2 x 5.25” ODD drives

Storage drive installation options

5.25″ ODD x 1 or 3.5” HDD x 1 or 2.5” SSD x 2

PSU Installation
First remove the beams that supports the expansion card retainer

ATX (PS2) Installation
PSU mounting bracket is pre-installed at the rear side, if the positions is to be interchanged, ensure the PSU mounting bracket is also moved to the front PSU mounting position for installation

Secure PSU with screws

Mini Redundant Installation

Remove the PSU mounting bracket
Attach and secure the additional PSU mounting bracket included in the accessories package to the chassis SILVERSTONE-RM47-502I-4U-Interchangeable-
Rackmount-Chassis- \(21\)Install and secure the PSU to the chassis

I/O panel can also be interchanged between front and rear side

Rear mounting position / Front mounting position SILVERSTONE-RM47-502I-4U-
Interchangeable-Rackmount-Chassis- \(23\)

Handlebars can also be interchanged between the front and rear side

Rear mounting position / Front mounting position

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(24\)

Rail slides
Due to its interchangeable nature, when mounting the RMS05-22 rail slides, ensure that the inner rails are screwed and secured into the designated mounting holes

Component restrictions

CPU cooler height limitations
Maximum height with expansion card holder: 114mm
Maximum height without expansion card holder: 148mm

CPU cooler is allowed to protrude 7mm over the edge of the motherboard
When 2.5” SSD mounting bracket is installed on the side, the distance between the CPU cooler and the edge of the motherboard must be greater than 5mm SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(27\)

PSU and 5.25” device restrictions
The measurements from the front to the rear is 455mm Considering the cable management requirements, it is recommended that the length of the PSU and 5.25” device should not exceed 430mm

Graphics card restrictions

  • Graphics card and fan/radiator total thickness cannot exceed 438mm
  • The total thickness of the full-height graphics card + the height of the low-profile expansion card equates to 142mm

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(29\)

Radiator restrictions

I/O panel installed at the rear
The radiator compatibility allows three combinations between 280mm, 240mm or 120mm When installing a 280mm radiator, please install the fan(s) between the rear chassis panel and the radiator to avoid interference with the I/O panel Maximum length limitation for radiator

Cooling fans limitations

If the I/O panel is located at the rear, the maximum number of fans is 2 x 140mm
If the I/O panel is located at the front, allows installation of 160mm fans with 140mm mounting holes

SILVERSTONE-RM47-502I-4U-Interchangeable-Rackmount-Chassis-
\(33\)

Installation of RS232 ports
Can purchase optional SilverStone ECD01 (Internal USB 2.0 to dual RS232 port adapter) to be installed in the RS232 reserved ports

Warranty Information

This product has a limited 1 year warranty in North America and Australia.
For information on warranty periods in other regions, please contact your reseller or SilverStone authorized distributor.
Warranty terms & conditions

  1. Product component defects or damages resulted from defective production is covered under warranty.
    Defects or damages with the following conditions will be fixed or replaced under SilverStone
    Technology’s jurisdiction.t

    • Usage in accordance with instructions provided in this manual, with no misuse, overuse, or other inappropriate actions.
    • Damage not caused by natural disaster (thunder, fire, earthquake, flood, salt, wind, insect, animals, etc…)
    • Product is not disassembled, modified, or fixed. Components not disassembled or replaced.
    • Warranty mark/stickers are not removed or broken.
      Loss or damages resulted from conditions other than ones listed above are not covered under warranty.
  2. Under warranty, SilverStone Technology’s maximum liability is limited to the current market value for the product (depreciated value, excluding shipping, handling, and other fees). SilverStone Technology is not responsible for other damages or loss associated with the use of product.

  3. Under warranty, SilverStone Technology is obligated to repair or replace its defective products. Under no circumstances will SilverStone Technology be liable for damages in connection with the sale, purchase, or use including but not limited to loss of data, loss of business, loss of profits, loss of use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty, contract or negligence, even if SilverStone Technology has been advised of the possibility of such damages.

  4. Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable to a second hand purchaser.

  5. You must provide sales receipt or invoice with clear indication of purchase date to determine warranty eligibility.

  6. If a problem develops during the warranty period, please contact your retailer/reseller/SilverStone authorized distributors or SilverStone http://www.silverstonetek.com . Please note that: (i) You must provide proof of original purchase of the product by a dated itemized receipt; (ii) You shall bear the cost of shipping (or otherwise transporting) the product to SilverStone authorized distributors. SilverStone authorized distributors will bear the cost of shipping (or otherwise transporting) the product back to you after completing the warranty service; (iii) Before you send the product, you must be issued a Return Merchandise Authorization (“RMA”) number from SilverStone. Updated warranty information will be posted on SilverStone’s official website.
    Please visit http://www.silverstonetek.com for the latest updates.

Additional info & contacts

For North America (usasupport@silverstonetek.com)
SilverStone Technology in North America may repair or replace defective product with refurbished product that is not new but has been functionally tested.
Replacement product will be warranted for remainder of the warranty period or thirty days, whichever is longer. All products should be sent
back to the place of purchase if it is within 30 days of purchase, after 30 days, customers need to initiate RMA procedure with SilverStone Technology in USA by first downloading the “USA RMA form for end-users” form from the below link and follow its instructions. http://silverstonetek.com/contactus.php
For Australia only (support@silverstonetek.com)
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Please refer to above “Warranty terms & conditions” for further warranty details.
SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan R.O.C. + 886-2-8228-1238 (standard international call charges apply)
For Europe (support.eu@silverstonetek.de)
For China (support@silverstonetek.com.cn)
For all other regions (support@silverstonetek.com)

SilverStone Technology Co., Ltd. www.silverstonetek.com support@silverstonetek.com

Please select text to grab.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SilverStone User Manuals

Related Manuals