VIDEOTEC VIP6A Wiper Kit Instruction Manual
- June 4, 2024
- VIDEOTEC
Table of Contents
VIDEOTEC VIP6A Wiper Kit
About this manual
Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.
Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the power supply before proceeding with any
operation, unless indicated otherwise.
WARNING!
Medium level hazard.
This operation is very important for the system to function properly. Please
read the procedure described very carefully and carry it out as instructed.
INFO
Description of system specifications. We recommend reading this part carefully
in order to understand the subsequent stages.
Notes on copyright and information on trademarks
The quoted names of products or companies are trademarks or registered
trademarks.
Safety rules
T he manufacturer declines all responsibility for any damage caused by an improper use of the appliances mentioned in this manual. Furthermore, the manufacturer reserves the right to modify its contents without any prior notice. The documentation contained in this manual has been collected with great care, the manufacturer, however, cannot take any liability for its use. The same thing can be said for any person or company involved in the creation and production of this manual.
- The device must be installed only and exclusively by qualified technical personnel.
- Before any technical work on the appliance, disconnect the power supply.
- Do not use power supply cables that seem worn or old.
- Never, under any circumstances, make any changes or connections that are not shown in this handbook: improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation.
- Use only original spare parts. Not original spare parts could cause fire, electrical discharge or other hazards.
- Before proceeding with installation check the supplied material to make sure it corresponds to the order specification by examining the identification labels (“4.2 Product markings”, page 1).
Identification
Product description and type designation
Wiper kit which can be directly installed on the housing body. It completes
the support for the pump washing injector. Available in 24Vac and 230Vac
versions, 7W max. Available for HEG series housing.
Product markings
See the label attached to the outside of the package.
Preparing the product for use
Any change that is not expressly approved by the manufacturer will invalidate the guarantee.
Safety precautions before use
In the 230Vac powered configuration, it is necessary to insert a 1 0 unipolar
main switch (open contact distance d>3mm) upstream on the power line. This
switch should be used to disconnect the power supply before carrying out any
maintenance operation or before opening the housing.
Contents and unpacking
When the product is delivered, make sure that the package is intact and that
there are no signs that it has been dropped or scratched. If there are obvious
signs of damage, contact the supplier immediately. Keep the packaging in case
you need to send the product for repairs.
Check the contents to make sure they correspond with the list of materials as below:
- Wiper kit
- Instructions manual
Safely disposing of packaging material
The packaging material can all be recycled. The installer technician will be
responsible for separating the material for disposal, and in any case for
compliance with the legislation in force where the device is to be used.
Bear in mind that if the material has to be returned due to a fault, using the original packaging for its transport is strongly recommended.
Assembling and installing
Only specialised personnel should be allowed to assemble and install the device.
Installation
Installing the wiper kit on the housing.
Remove the front flange on the housing by unscrewing the three front screws
.
Insert the wiper body by slotting the slide onto the profile of the housing
body.
Slide the wiper body along the housing body.
Re-assemble the front flange on the housing by tightening the three front screws, making sure the sealing gasket is seated properly.
Assemble the wiper blade on the output shaft, fixing it in the rest position
on the left side of the glass front.
Lock the wiper body by tightening up the dowels on the fixing slide so that
the blade exerts the correct pressure on the housing glass.
Wiring
Make sure the power supply voltage used is the same shown on the plate on
the back of the appliance.
Make the electrical connections on the female 3+PE connector as shown in the
electrical diagram.
Power the wiper by connecting the phase to terminal 03 (SW) on the connector and neutral to terminal 02 (COM) on the connector. Use an external button to connect the phase to terminal 01 (PERM) on the connector. Keeping the external button pressed will cause continuous operation (permanent) of the wiper. Releasing the button will take the wiper blade to the rest position on the left side of the housing window.
If a receiver is used, connect terminal 03 of the connector to the SW output on the receiver, 01 to PERM and 02 to COM.
Instructions for normal operation
Do not use the wiper when the outside temperature is below 0°C or in case
of ice.
Disposal of waste materials
This symbol mark and recycle system ar e applied only to EU countries and
not applied to the countries in the other area of the world.
Your product is designed and manufactured with high-quality materials and
components that can be recycled and reused. This symbol means that electrical
and electronic equipment, at their end of life, should be disposed of
separately from your household waste.
Please dispose of this equipment at your local Community waste collection or Recycling center. In the European Union, there are separate collection systems for used electrical and electronic products.
Technical data
General
- Enclosure from reinforced polypropylene
- Wiper blade constructed from stainless steel/aluminum
- RAL9002 color
- IP66
- Dimensions (WxHxL): 99x114x209mm (3.8×4.4×8.2 in) (not comprehensive of the blade)
- Unit weight: 0.7kg / 1.5lb
- Connector 3+1 PINS
- IN 230Vac, consumption 7W max
- IN 24Vac, consumption 7W max
- Operating temperature: -20°C / +60°C (-4°F / +140°F)
- Supplied with an instruction manual
- EAC certification
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>