VIDEOTEC PUNTO-HI-POE Technopolymer Housing for IP Camera Instruction Manual
- June 4, 2024
- VIDEOTEC
Table of Contents
- VIDEOTEC PUNTO-HI-POE Technopolymer Housing for IP Camera
- Typographical conventions
- Notes on copyright and information on trademarks
- Safety rules
- Identification
- Preparing the product for use
- Assembly
- Installation
- Configuration
- Cleaning
- Disposal of waste materials
- Technical data
- Technical drawings
- ABOUT COMPANY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VIDEOTEC PUNTO-HI-POE Technopolymer Housing for IP Camera
Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.
Typographical conventions
- DANGER!
- High level hazard.
- Risk of electric shock. Disconnect the power supply before proceeding with any operation, unless indicated otherwise.
- CAUTION!
- Medium level hazard.
- This operation is very important for the system to function properly. Please read the procedure described very carefully and carry it out as instructed.
- INFO
- Description of system specifications.
- We recommend reading this part carefully in order to understand the subsequent stages.
Notes on copyright and information on trademarks
The quoted names of products or companies are trademarks or registered trademarks.
Safety rules
CAUTION! The device must be installed only and exclusively by skilled
technical personnel.
CAUTION! The electrical system to which the unit is connected must be
equipped with a 10A max automatic bipolar circuit breaker. This circuit
breaker must be of the Listed type. The minimum distance between the contacts
must be 3mm (0.1in). The circuit breaker must be provided with protection
against the fault current towards the ground (differential) and the over
current (magnet thermal).
- The manufacturer declines all responsibility for any damage caused by an improper use of the appliances mentioned in this manual. Furthermore, the manufacturer reserves the right to modify its contents without any prior notice. The documentation contained in this manual has been collected with great care. The manufacturer, however, cannot take any liability for its use. The same thing can be said for any person or company involved in the creation and production of this manual.
- Before starting any operation, make sure the power supply is disconnected.
- Do not use cables that seem worn or old.
- Never, under any circumstances, make any changes or connections that are not shown in this handbook. Improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation.
- Use only original spare parts. Non-original spare parts could cause fire, electrical discharge or other hazards.
- Before proceeding with installation, check the supplied material to make sure it corresponds to the order specification by examining the identification labels (4.2 Product markings, page 4).
- This device was designed to be permanently installed on a building or on a suitable structure. The device must be installed permanently before any operation.
- When installing the device, comply with all the national standards.
- Any device which could be installed inside the product must comply with the current safety standards.
- For all connections, use cables that are able to withstand temperatures of at least 75°C (167°F).
- Power supply to the product must be exclusively provided by the PoE cable (Power over Ethernet).
- Use power supplies compliant with regulations IEEE 802.3at/af and 60950-1/62368-1.
- The product must be fastened with suitable equipment. The fastening means must guarantee the mechanical seal when a force equal to at least 4 times the weight of the device is applied.
Identification
Product description and type designation
- The PUNTO Hi-PoE housing exploits the PoE and Hi-PoE technology in an optimal way, using the power provided by the Ethernet cable as the sole source of electricity to power the network camera along with heating/demisting.
- PUNTO Hi-PoE provides high reliability and flexibility of the network installation and simplifies installation operations with important cost reduction.
- PUNTO Hi-PoE can be configured via a dip switch according to the PoE or Hi-PoE standards depending to the system requirements.
- Very easy to install thanks to the side opening system that allows the full access to the camera, lenses and all internal connections.
- The front is designed to offer protection from UV rays and atmospheric agents.
Product markings
See the label attached to the product.
Preparing the product for use
Any change that is not expressly approved by the manufacturer will invalidate the guarantee.
Unpacking
- When the product is delivered, make sure that the package is intact and that there are no signs that it has been dropped or scratched.
- If there are obvious signs of damage, contact the supplier immediately.
- Keep the packaging in case you need to send the product for repairs.
Contents
Check the contents to make sure they correspond with the list of materials as
below:
- Housing
- Housing equipment
- Instructions manual
- Desiccant bag
Safely disposing of packaging material
- The packaging material can all be recycled. The installer technician will be responsible for separating the material for disposal, and in any case for compliance with the legislation in force where the device is to be used.
- When returning a faulty product we recommend using the original packaging for shipping.
Preparatory work before installation
- Attaching the bracket
The product must be fastened with suitable equipment. The fastening means must guarantee the mechanical seal when a force equal to at least 4 times the weight of the device is applied.
Assembly
How to open the housing
Loosen the 2 screws on the side, turn the cover and the upper half of the body
about the opening hinge axis.
Cable glands assembly
- The cable glands are suitable for cables with a diameter between 5mm and 10 mm.
- Fix the cable glands as shown in the figure.
Fixing the sun shield
It’s possible to fix the sun shield to the housing using screws, washers and
spacers provided.
Installation
Fixing of housing to support
- Apply a thread-locker on the holes of the screws (Loctite 243®).
- Fix the housing to the support using the supplied screws.
How to install the camera
- Fasten the camera with the 1/4″ screw (03). To position the camera and lens correctly, if necessary, use the supplied spacers. (04).
- Fasten down the adjustable slide in the correct position using the appropriate screws.
Ethernet cable installation
-
Insert the Ethernet cable in the gasket and block it as shown in figure.
Pay attention to the fixing. Tightening torque: 7Nm. -
Pass the cable with connector RJ45 (05) through the M20 cable gland (02). Tighten the cable gland plug (06).
Connection of the PoE power supply board
- Connect the PoE cable from the Power Injector to the J1 connector.
- Connect the camera to the J2 connector.
Configuration
Absorbed power configuration
Before powering the device, you must set the maximum power consumption of the
housing operating on dip switch SW1.
ABSORBED POWER CONFIGURATION
SW1| Maximum power
POE| PoE, class 3 (13W max)
POE+| Hi-PoE, class 4 (25W max)
Operating status
The LEDs shown in the figure allow to check the product’s operating status.
Refer to the table to identify the operating status.
OPERATING STATUS
LED| LED Status| Apparatus Status
LD1 (Ca-
mera)
| Off| The camera is not connected
On| The camera is correctly powered
1 flashing| The camera has a low identifica- tion resistance
2 flashings| The camera has a high identifi- cation resistance
5 flashings| The camera has an excessive energy consumption
9 flashings| The camera requires more energy than the available
LD2 (Power supply)| Off| The device is not powered
On| The device is correctly powered
LD3 (He-
ater)
| Off| Heating is inactive
On| Heating is active
Closing the housing
Take the dessicant salt bag out of its pack and insert it into the product. At
the end of the installation close the housing.
Cleaning
Window and plastic cover cleaning
- Avoid ethyl alcohol, solvents, hydrogenated hydrocarbide, strong acid and alkali. Such products may irreparably damage the surface.
- We recommend using a soft cloth with neutral soaps diluted with water or specific products to clean the glasses lenses.
Disposal of waste materials
This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world.
- Your product is designed and manufactured with high quality materials and components which can be recycled and reused.
- This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.
- Please dispose of this equipment at your local Community waste collection or Recycling centre.
- In the European Union there are separate collection systems for used electrical and electronic products.
Technical data
General
- Entirely made of technopolymer, RAL9002 colour
- Stainless steel external screws
Mechanical
- Cable glands: 1xM20
- Glass window (WxH): 60/95x63mm (2.4/3.7×2.5in)
- Internal usable area (WxH): 70x70mm (2.7×2.7in)
- Internal usable length: 250mm (9.8in)
- Unit weight: 0.8kg (1.7lb)
Electrical
- Power absorbed in input/Available power for camera (selectable with dip-switch)
- PoE input Class 3 (13W): PoE camera Class 2 (7W)
- Hi-PoE input Class 4 (25W): PoE camera Class 3 (13W)
- Data line: 10/100Base-T
- Heater
- PoE input Class 3: 3W, Ton 15°C±3°C (59°F ±5°F), Toff 22°C±3°C (77°F±5°F)
- Hi-PoE input Class 4: 7W, Ton 15°C±3°C (59°F ±5°F), Toff 22°C±3°C (77°F±5°F)
- Demisting: 1W
Compatible with IEEE 802.3af, IEEE 802.3at/PoE Plus
Environment
- Indoor/Outdoor
- Operating temperature with heating: From -20°C (-4°F) a +60°C (140°F)
- Chemical agents resistance
- High resistance: basics, alcohols, gas, hydrocarbon
- Good resistance: Organic acids, inorganic acids, oils
- Low resistance: Solvents
Certifications
- Electrical safety (CE): EN60950-1, EN62368-1, IEC62368-1
- Electromagnetic compatibility (CE): EN50130-4, EN61000-6-3
- Outdoor installation (CE): EN60950-22, IEC 60950-22
- IP protection degree: EN60529, IP66
- UL certification: cULus Listed (TYPE 4X)
- EAC certification
Technical drawings
The dimensions of the drawings are in millimetres.
ABOUT COMPANY
- Headquarters Italy VIDEOTEC s.r.l.
- Via Friuli, 6 – I-36015 Schio (VI) – Italy
- Tel. +39 0445 697411
- Fax +39 0445 697414
- Email: info@videotec.com
- www.videotec.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>