FNW 7203 Malleable Iron Beam Clamps Instruction Manual
- June 13, 2024
- FNW
Table of Contents
FNW 7203 Malleable Iron Beam Clamps
Product Information
The FNW figure 7203 and 7204 beam clamps are malleable iron beam clamps used for installation purposes. This product is designed to securely hold loads in line with threaded rods, ensuring proper installation and preventing failure of the beam clamp. The beam clamps are available in different sizes and have load and temperature capacities as specified in the table below:
INSTALLATION INSTRUCTIONS
MALLEABLE IRON BEAM CLAMPS
This instruction manual includes installation and proper use information
for FNW figure 7203 and 7204 malleable iron beam clamps.
PROPER USE
To avoid personal injury to yourself, fellow workers, or damage to property
from improper use:
- Verify beam clamps are used within listed load and temperature limits (see load charts, page 2).
- Only install beam clamps with loads in line with threaded rod (suppled by others).
- Do not install beam clamps with loads at angles to threaded rod or by bending threaded rod as stresses can be transmitted unpredictably to the clamp.
- Reverse installation of beam clamps is not allowed. *3/8″ only size acceptable for reverse installation (max load 200 lbs).
- Only use hardware (i.e. Clamp, Set Screw, and Hex Nut) suppled in this kit. Use of third party hardware will void any warranty with FNW.
- Do not overtighten set screw beyond what is outlined in these instructions. Overtightening can reduce load capacity up to and including failure of the beam clamp.
YES
Proper installation with load in line with threaded rod.
NO
Improper installation with load at angle to threaded rod.
NO
Improper installation with bent threaded rod.
NO
Improper installation with beam clam in reverse direction. *3/8″ only size
acceptable for reverse installation (max load 200 lbs).
The FNW figure 7203 and 7204 beam clamp can be installed with, or without, a torque wrench.
With Torque Wrench
- Place clamp, without load, onto beam.
- Tighten the set screw to 5.0 ft-lbs (60 in-lbs).
- Tighten the hex nut to lock the set screw in place.
- Place clamp, without load, onto beam.
- Tighten the screw set to finger tight.
- Using a wrench, continue tightening the set screw an additional 1/4 to 1/3 turn.
- Tighten the hex nut to lock the set screw in place.
DO NOT OVERTIGHTEN THE SET SCREW
We reserve the right to modify or improve the designs or specifications of
our products at any time without notice.
LOAD & TEMPERATURE CAPACITIES
The FNW figure 7203 and 7204 brochure list their maximum load capabilities when used within the standard temperature range of 5°F to 212°F. Extended temperature range of -22°F through 5°F and 212°F through 482°F is permitted at the reduced load capacity of 60% maximum (i.e. extended temperature ranges reduce maximum load capacity by 40%). The chart below lists standard and reduced capacity load capabilities depending on temperature.
Figure
__**__**Number
|
Rod
__**__**Size
| Maximum Pipe Size
__**Recommended**
| Maximum Recommended Load (Lbs.)| Recommended Load (Lbs.) Per
Temperature Range
---|---|---|---|---
Regular Installation
__**(Top Mount)**
| Reverse Installation
__**(Bottom Mount)**
| 5°F – 212°F| -22°F – 5°F or 212°F – 482°F
7203| 3/8″
1/2″
5/8″
| 4″
8″
8″
| 560
810
1000
| 200
Not Allowed Not Allowed
| 400
500
600
| 240
300
360
3/4″| 8″| 1500| Not Allowed| 800| 480
7204| 3/8″| 4″| 560| Not Allowed| 400| 240
1/2″| 8″| 810| Not Allowed| 500| 300
5/8″| 5″| 1000| Not Allowed| 850| 510
3/4″| 6″| 1500| Not Allowed| 900| 540
WARRANTY
LIMITED WARRANTY
Subject to the limitations expressed herein, Seller warrants that products
manufactured by Seller shall be free from defects in design, material and
workmanship under normal use for a period of one (1) year from installation
but in no case shall the warranty period extend longer than eighteen months
from the date of sale. This warranty is void for any damage caused by misuse,
abuse, neglect, acts of God, or improper installation. For the purpose of this
section, “Normal Use” means in strict accordance with the installation,
operation and maintenance manual. The warranty for all other products is
provided by the original equipment manufacturer.
REMEDIES
Seller shall repair or replace, at its option, any non-conforming or otherwise
defective product, upon receipt of notice from Buyer during the Manufacturer’s
warranty period at no additional charge. SELLER HEREBY DISCLAIMS ALL OTHER
EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS OR FITNESS FOR A PARTICULAR PURPOSE.
LIMITATION OF LIABILITY
UNDER NO CIRCUMSTANCES SHALL EITHER PARTY BE LIABLE TO THE OTHER FOR
INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. BUYER
HEREBY ACKNOWLEDGES AND AGREES THAT UNDER NO CIRCUMSTANCES, AND IN NO EVENT,
SHALL SELLER’S LIABILITY, IF ANY, EXCEED THE NET SALES PRICE OF THE DEFECTIVE
PRODUCT(S) PURCHASED DURING THE PREVIOUS CONTRACT YEAR.
LABOR ALLOWANCE
Seller makes NO ADDITIONAL ALLOWANCE FOR THE LABOR OR EXPENSE OF REPAIRING OR
REPLACING DEFECTIVE PRODUCTS OR WORKMANSHIP OR DAMAGE RESULTING FROM THE SAME.
RECOMMENDATIONS BY SELLER
Seller may assist Buyer in selection decisions by providing information
regarding products that it manufacturers and those manufactured by others.
However, Buyer acknowledges that Buyer ultimately chooses the product’s
suitability for its particular use, as normally signified by the signature of
Buyer’s technical representative. Any recommendations made by Seller
concerning the use, design, application or operation of the products shall not
be construed as representations or warranties, expressed or implied. Failure
by Seller to make recommendations or give advice to Buyer shall not impose any
liability upon Seller.
EXCUSED PERFORMANCE
Seller will make a good faith effort to complete delivery of the products as
indicated by Seller in writing, but Seller assumes no responsibility or
liability and will accept no back-charge for loss or damage due to delay or
inability to deliver, caused by acts of God, war, labor difficulties,
accidents, inability to obtain materials, delays of carriers, contractors or
suppliers or any other causes of any kind whatever beyond the control of
Seller. Under no circumstances shall Seller be liable for any special,
consequential, incidental, or indirect damages, losses, or expense (whether or
not based on negligence) arising directly or indirectly from delays or failure
to give notice of delay.
FNW.COM
©2022 Ferguson Enterprises, LLC 0922 4490259
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>