ORANGE Terror Bass Owner’s Manual

June 7, 2024
ORANGE

ORANGE Terror Bass Owner’s Manual
ORANGE Terror Bass

IMPORTANT SAFETY INSTRUCTIONS

  1. Read these instructions.
  2. Keep these instructions.
  3. Heed all warnings.
  4.  Follow all instructions.
  5. Do not use this apparatus near water.
  6. Clean only with a dry cloth.
  7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
  9. Do not defeat the safety purpose of the polarised or grounding-type plug. A polarised plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the  third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet
  10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
  11. Only use attachments/accessories specified by the manufacturer.
  12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.When a cart is used, use caution  when moving the cart/apparatus combination to avoid injury from tip-over.
  13. Unplug this apparatus during lightning storms or when unused for  long periods of time.
  14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Caution : The exclamation point within an equilateral triangle and “WARNING”  are intended to alert the user to the presence of important operating or servicing instructions. Failure to heed the instructions will result in severe injury or death.

This equipment should be used under the supervision of an adult at all times.

Warning : The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un- insulated  ‘dangerous voltage’ within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons. Terminals labelled as “SPEAKER  OUTPUTS” must be connected to a speaker cabinet of the designated load (Ω) rating using an un-shielded two conductor cable for speaker use at all times during operation.

The “Caution, hot surface” symbol indicates that the marked item may be hot.

Do not cover or block ventilation openings. Ensure the apparatus is installed with plenty of space around the unit (> 6”/12.5cm) as this apparatus may generate heat under normal use. This equipment is not intended to be used on soft support (like beddings, blankets etc.). This equipment should always be placed on a flat, stable surface.

  • To reduce the risk of fire and electric shock do not expose this apparatus to rain or moisture.
  • For indoor use only.
  • Do not use in damp environments, e.g. bathrooms etc.
  • Do not place objects containing liquids on, or near the product.
  • Do not operate this apparatus or connect/disconnect a power plug whilst  hands are wet.
  • Do not attempt to gain access to the interior of the product. No user serviceable parts inside. Refer all servicing to qualified servicing personnel.

This symbol indicates this product is classified as Waste Electrical and Electronic Equipment (WEEE) in the European Union and should not be discarded with household waste. Contact your local authority for more information and details of  your nearest approved disposal facility.

POWERING YOUR UNIT

WARNING

FUSE INFORMATION

The mains fuse is provided for your safety. The fuse rating for your model and region is indicated near the unit’s AC mains inlet Do not replace with a fuse of a different type

  • T = Time Delay (“Slow Blow”) mA or A = Rated current, expressed in mA or A
  • L = Low breaking capacity or;
  • H = High breaking capacity

If the mains fuse repeatedly blows, contact your Orange dealer.

iconDO NOT TAMPER WITH VOLTAGE SELECTOR SWITCH

The voltage selector switch is located on the rear or side of the product. It is set at the factory for the country or region in which the unit is intended to be sold. If the unit is to be used oversees, contact Orange Amplification.

GENERAL USE

  • Before switching on the power, set the unit’s volume control(s) to minimum.
  • Ensure the correct speaker load is connected at all times during operation. Refer to the section entitled “SPEAKER OUTPUTS”
  • Use good quality shielded instrument cable to connect your instrument to your unit’s input.
  • To prevent excessive hum and electrical noise, operate your amplifier and instruments as far away as possible from other electronic devices.  Examples include: refrigerators, motors, air conditioners, television sets, radio receivers etc.

START UP PROCEDURE FOR VALVE AMPLIFIERS

Before switching the POWER switch to the O N position, ensure the OFF/STBY/ON switch is set to the STBY (Startup Tension Bypass) mode.

Leave the amp in STBY mode for at least 2 minutes prior to performance. This will help prolong the life of the valves [tubes]. After 2 minutes, switch to play mode. Select the STBY mode during breaks in performance.

START UP PROCEDURE FOR VALVE AMPLIFIERS

SERVICING INFORMATION FOR VALVE AMPLIFIERS

Periodic valve renewal should be considered part of owning a quality valve [tube] amplifier. The rate of valve wear is dependent on many factors, but if you notice a change in the performance of your amplifier, it is likely a result of valve decline. Valves can fail at any time. Output valves (EL84, EL34, 6550 etc.) are subject to more stress than preamp valves (12AX7, 12AT7 etc.) and may require more regular replacement. Consult your service centre/dealer for more information.

Output valves should always be replaced with matched sets, though not all models require a bias adjustment. Contact your Orange dealer for more information.

Bias adjustment should only be performed by authorised service personnel.

The fuse labelled “HT FUSE” will blow in the event of output valve failure. The output valve(s) should be replaced, and the HT fuse replaced with the correct 250V type.The rating is indicated on the product near the HT fuse holder.

Our Orange Valve Tester can be used to help match valves and check valve health.

Visit orangeamps.com for more information.

FRONT PANEL

FRONT PANEL

PAD SWITCH
The pad switch on the front is for active basses which takes 6dB off the input sensitivity.

CLEAN SWITCH
The clean switch gives more headroom and smoother clean sounds.

ORANGE ICONS
  • INPUT  : ¼” instrument jack socket.
  • POWER  : The lamp will illuminate to indicate the power is switched to ON.
  • FX LOOP : Used to place external effects between the amplifier’s preamplifier section and output section. Connect the SEND jack to the  input of external effects. Connect the output of external effects to the  RETURN jack.
  • iconVOLUME : Adjusts the volume level for either the Natural or Dirty channel.
  • GAIN : Controls the (preamplifier) gain level. Higher settings produce more distortion. Note: When set to minimum, no sound will be heard.
  • BASS : Adjusts the lower frequency response. Increasing the bass produces deeper sounds.
  • MID : Adjusts the midrange response. Increasing the mids creates  a fatter sound, whilst reducing‘scoops’ the tone.
  • TREBLE : Adjusts the high frequency response. Increase the treble for brighter tones or reduce for a warmer sound.

REAR / SIDE CONNECTIONS

BALANCED DI OUTPUT

BALANCED DI OUTPUT

BALANCED DI OUTPUT

DI OUTPUT The DI output is set at professional line level for a padded mixing desk to a PA. An external DI box should still be taken from the actual bass guitar itself in most live situations so that a signal can still be present in case of amplifier failure.
IMPORTANT: A speaker cabinet of suitable impedance and power handling must be connected to the amplifier’s speaker outputs even when the DI Output is in use.

FX LOOP

FX LOOP

SPEAKER OUTPUTS
  • 1 x SPEAKER ( 4 Ω OR 8 Ω )
    SPEAKER OUTPUTS

  • 2 x SPEAKER ( 8 Ω )
    SPEAKER OUTPUTS

Make sure this switch matches your speakers impedance

SPEAKER OUTPUTS

  • NEVER PLUG ANYTHING OTHER THAN A SPEAKER CABLE INTO THE SPEAKER OUTPUT.
  • ONLY CONNECT SPEAKER CABINETS AS SHOWN.
  • NEVER USE AN INSTRUMENT CABLE TO CONNECT SPEAKERS. ONLY USE UNSHIELDED TWO CONDUCTOR SPEAKER CABLE.
  • NEVER CONNECT X 2 CABINETS OF DIFFERENT IMPEDANCES (Ω).
  • ENSURE THE SPEAKER CABINET’S POWER HANDLING RATING (WATTS RMS) IS SUITABLE FOR YOUR AMPLIFIER. IF YOU ARE UNSURE, CONTACT YOUR ORANGE DEALER.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals