orange PI 3 LTS Single Board Computer User Manual
- June 11, 2024
- orange PI
Table of Contents
Orange Pi 3 LTS
Official website data download:
http://www.orangepi.org/downloadresources/
Product description
What’s Orange Pi 3 LTS?
It’ s an open-source single board computer. It can run Android 9, Ubuntu, Debian. It uses the Allwinner H6 SoC, and has 2GB LPDDR3 SDRAM.
Top view
-
26 Pin headers
-
PMU
-
Allwinner H6
(ARM® Cortex -A53 Quad-core 1.8GHZ ) 64 bit -
WiFi + BT
-
Ethernet chip
-
IR Receiver
-
USB2.0
-
Gigabit Ethernet
-
WiFi Antenna
-
USB3.0+USB2.0
-
Audio output and AV
-
MIC
-
HDMI
-
Debug TTL UART
-
8GB EMMC Flash
-
Power switch
-
LED
-
2GB LPDDR3
-
USB Type-C power interface
Bottom view
- TF card slot
Orange Pi 3 LTS v1.2 pinout diagram
Who’s it for?
Orange Pi 3 LTS is for anyone who wants to start creating with technology – not just consuming it. It’s a simple, fun, useful tool that you can use to start taking control of the world around you.
What can I do with Orange Pi 3 LTS?
You can use it to build……
- A computer
- A wireless server
- Games
- Music and sounds
- HD video
- A speaker
- Android
- Scratch
Pretty much anything else, because Orange Pi 3 LTS is open source.
Orange Pi 3 VS Orange Pi 3 LTS
Model
| Orange Pi 3| Orange Pi 3 LTS
---|---|---
Hardware features
SOC| Allwinner H6 64bit|
Allwinner H6 64bit
CPU Architecture
| Cortex™-A53| Cortex™-A53
CPU Frequency| 1.8GHz|
1.8GHz
Onboard Storage
| •MicrosD Card •8GB EMMC Flash/EMMC(Default Empty)| •MicrosD Card •8GB EMMC
Flash
Core Number| 4|
4
Memory Bus
| LPDDR3| LPDDR3
Memory| 1GB/2GB|
2GB
WiFi+BT5.0
| AP6256| AW859A
Network| 10M/100M/1000M Ethernet|
10M/100M/1000M Ethernet
USB
| 1USB2.0+4USB3.0| 2USB2.0+1USB3.0
PCB Size| 60×93.5mm|
56x85mm
Power Interface
| DC Input, MicroUSB (OTG)| 5V3A Type-C
PMU | Yes |
Yes
PCIE
| Yes | –
Software features
OS
| Android7.0,Ubuntu,Debian|
Android9.0,Ubuntu,Debian
Orange Pi 3, Orange Pi 3 LTS Dimension
Orange Pi 3 Orange Pi 3 LTS
Hardware specification:
CPU
| Allwinner H6 Quad-Core 64-Bit 1.8GHz High-Performance Cortex-A53 Processor
---|---
GPU
|
- High-performance multi-core GPU Mali T720
- OpenGL ES3.1/3.0/2.0/1.1
- Microsoft DirectX 11 FL9_3
- ASTC(Adaptive Scalable Texture Compression)
- Floating point operation greater than 70 GFLOPS
RAM
| 2GB LPDDR3 (Shared with GPU)
Onboard Storage
|
- Micro SD Card Slot
- 8GB EMMC Flash
Onboard Ethernet
|
- YT8531C Chip
- Support 10/100M/1000M Ethernet
Onboard WIFI+Bluetooth
|
- AW859A Chip
- Support IEEE 802.11 a/b/g/n/ac
- Support BT5.0
Video Output
|
- HDMI 2.0a
- TV CVBS Output
Audio Output
|
- HDMI Output
- 3.5mm Audio Port
Power Supply
| 5V3A Type-C
Power Management Chip
| AXP805
USB Port
| 1 USB 3.0 HOST, 2 USB 2.0 HOST
Low-Level Peripherals
|
- 26Pin Connector With 1I2C, 1SPI, 1*UART & Multiple GPIO Ports
Debug Serial Port
| UART-TX, UART-RX & GND
LED
| Power LED & Status LED
IR Receiver
| Support IR Remote Control
Button
| Power Button (SW4)
Supported OS
| Android 9.0, Ubuntu, Debian
Appearance specification introduction:
Dimension
| 56mm x 85mm
---|---
weight
| 45g
is a trademark of the Shenzhen Xunlong Software CO., Limited
Completely open source maker artifact
Orange Pi 3 LTS runs Android
Orange Pi 3 LTS runs Ubuntu / Debian
Product display
Front
Back
45° angle
45° angle
45° angle
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>