OTBeat Burn User Manual: How to Pair & Use Heart Rate Monitor | Orangetheory

The OTBeat Burn User Manual is a comprehensive guide for users of the Orangetheory heart rate monitor. The manual provides step-by-step instructions on how to pair and use the device, including downloading the Orangetheory app, charging the device, and proper placement for accurate data transmission. The manual also includes an LED guide, which helps users understand the different LED indications for heart rate detection, Bluetooth connection state, and battery status. Additionally, the manual provides technical specifications for the device, including heart rate range, accuracy, transmission distance, battery life, and water resistance level. The manual emphasizes the importance of caring for the device to ensure accurate readings and provides instructions on how to clean the sensor lens and USB charging contacts. For more information, users can visit the Orangetheory website or post questions in the comments section.

USER MANUAL

OTBeat Burn

Getting Started:

1. Included in packaging: OTbeat Burn, SM band, LG band, & USB cord
2. Remove OTbeat Burn from packaging
3. Connect USB cord into charging port of device
4. LED light will appear after a few seconds

Downloading the Orangetheory App:

*Using your mobile device, download the Orangetheory App.

Note: Fully charge device before attempting to pair for the first time.

Charging Device:

1. Open rubber port cover on back of device
2. Plug in mini-USB connector into device port
3. Plug in regular USB connector into charging block
4. Plug in charging block into wall outlet

Device can be connected directly to a computer USB port.
Note: The voltage differs from wall outlet to computer.

Battery is fully charged when Green LED is continuously on During charging: Red LED light will blink slowly LED indication for charging is in front of device

Proper Placement:

To transmit accurate data from your device:

1. Fasten device snugly in one of the below placement options
2. Wear device below, and not directly on top, of wrist bone* or elbow
3. The optical sensor on the back should make good contact with skin

*For placement on wrist, measure two fingers above wrist bone

Pairing Device:

1. Once OTbeat Burn is fully charged, press center of splat to power ON the device

2. Launch the settings app on your mobile device
3. Ensure your bluetooth settings are on

4. Open Orangetheory app on mobile phone.

5. Use the Orangetheory app to search for device

*Once device appears, OTbeat Burn is successfully connected to app

LED Guide

Heart Rate Detection LED Indication:

Alternating BLUE and GREEN: Detecting heart rate
Alternating BLUE and RED: No heart rate detected
Blinking GREEN: Heart rate detected
Blinking ORANGE: Heart rate zones are changing

Bluetooth Connection State:

Blue LED blinks for 5 seconds: After turning on the unit
Blue LED continuously on for 5 second: Connected
Green LED on for 2 seconds: Connected (HR not detected)
Green LED continuously on: Updating firmware

Battery LED Light

During Charging:
Red LED blinks slowly: Charging
Green LED continuously on: Battery full

Battery State:
Red LED blinks three times: Low battery at <15% (repeat every 5 min. until reach critical level)
Red LED continuously on for 2 sec: Device powering off

Caring for Device:

1. To ensure accurate readings, clean the sensor lens with a soft cloth
2. OTbeat Burn unit and strap are waterproof to IP67 specifications and can be easily cleaned with mild soap and cool water
3. Use a cotton swab and only rubbing alcohol to clean the USB charging contacts when necessary: do not contact USB charging port
4. Do not use any abrasive chemicals to clean the Otbeat Burn unit, sensor, or strap. This will cause permanent damage

Technical Specifications

Faqs

What is included in the packaging of the OTBeat Burn?

The packaging includes the OTbeat Burn, SM band, LG band, and USB cord.

How do I charge the device?

Open the rubber port cover on the back of the device, plug in the mini-USB connector into the device port, plug in the regular USB connector into the charging block, and plug in the charging block into a wall outlet. The device can also be connected directly to a computer USB port.

How do I pair the device?

Once the OTbeat Burn is fully charged, press the center of the splat to power on the device, launch the settings app on your mobile device, ensure your Bluetooth settings are on, open the Orangetheory app on your mobile phone, and use the app to search for the device. Once the device appears, the OTbeat Burn is successfully connected to the app.

How do I know if my heart rate is being detected?

Alternating blue and green LED lights indicate that your heart rate is being detected, blinking green indicates that your heart rate has been detected, and alternating blue and red indicate that no heart rate has been detected.

How do I care for my device?

To ensure accurate readings, clean the sensor lens with a soft cloth. The OTbeat Burn unit and strap are waterproof to IP67 specifications and can be easily cleaned with mild soap and cool water. Use a cotton swab and only rubbing alcohol to clean the USB charging contacts when necessary, but do not contact the USB charging port. Do not use any abrasive chemicals to clean the OTbeat Burn unit, sensor, or strap as this will cause permanent damage.

What are the technical specifications of the device?

The device features heart rate detection and transmission with a heart rate range of 30 to 220 BPM in 1 BPM resolution and a transmission accuracy of +/-5 BPM. It is powered by a 3.8V Li-ion Polymer rechargeable battery and has a transmission distance of 15 meters and a battery life of up to 24 hours of continuous detection. It is also water-resistant to IP67 specifications and has a memory capacity of 6 hours.

Read More About This Manual…

OTBeat-Burn-Manual-Optimized

OTBeat-Burn-Manual-Original

Questions about your Manual? Post in the comments!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>