Haier HCW58F18EHMP Refrigerator Freezer User Manual

Haier HCW58F18EHMP Refrigerator Freezer

Product Information

• Specifications:
  • Model: HCW58F18EHMP
  • Product Type: Refrigerator-Freezer
  • Language Options: GB, CS, DE, EL, ES, FR, HU, IT, NL, PL, PT, RO, HR, SK
• Product Information:
  • This Refrigerator-Freezer model HCW58F18EHMP is designed to provide efficient cooling and storage solutions for your kitchen.
  • It comes with various accessories such as an ice shovel, water pipe, and spacers.
• General Information:
  • Thank you for choosing a Haier Product.
  • Help protect the environment by recycling packaging materials and waste electrical appliances.
  • Ensure proper disposal of refrigerants and gases to prevent risks.
  • Safety precautions include disconnecting the appliance before disposal and supervising children during maintenance.

Product Usage Instructions

• Safety Information:
  • Power Cable Safety: Ensure the power cable is not damaged and fits a standard socket. Never cut off or dismount the grounding pin.
  • Child Safety: Supervise children under 8 years old when using the appliance. Children should not play with the appliance.
• Before First Use:
  • Read the safety hints provided in the manual before switching on the appliance for the first time.
• Cleaning and Maintenance:
  • Unplugging and Cleaning: Unplug the appliance before cleaning to avoid electrical hazards. Wait for 7 minutes before restarting after a power interruption.
  • Maintenance: Disconnect from the electrical supply before maintenance. Wait for 5 minutes before restarting after cleaning to avoid compressor damage.
  • Cleaning Tips: Use gentle cleaning tools; do not use hard brushes that may damage the appliance.
• FAQ:
  • Q: What should I do in case of a power interruption?
  • A: Unplug the appliance and wait for at least 7 minutes before restarting to prevent compressor damage.
  • Q: Can children use the appliance unsupervised?
  • A: Children under 8 years should be supervised when using the appliance to ensure safety.

Thank You

• Thank you for purchasing a Haier Product.
• Please read these instructions carefully before using this appliance. The instructions contain important information that will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance.
• Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
• If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass this manual so that the new owner can become familiar with the appliance and safety warnings.

Legend

• Warning – Important Safety information
• General information and tips
• Environmental information

Disposal

• Help protect the environment and human health.
  Put the packaging in applicable containers to recycle it.

• Help to recycle waste of electrical and electronic appliances.

• Do not dispose of appliances marked with this symbol with the household waste.

• Return the product to your local recycling facility or contact your municipal office.

WARNING!

Risk of injury or suffocation! Refrigerants and gases must be disposed of professionally. Ensure that the tubing of the refrigerant circuit is not damaged before being properly disposed of. Disconnect the appliance from the main supply. Cut off the main cable and dispose of it. Remove the trays and drawers as well as the door catch and seals, to prevent children and pets from getting closed in the appliance.

Accessories

Check the accessories and literature by this list:

Safety information

Before switching on the appliance for the first time read the following safety hints!:

WARNING!

• Before first use
  • Make sure there is no transport damage.
  • Remove all packaging and keep out of children´s reach.
  • Wait at least two hours before installing the appliance to ensure the refrigerant circuit is fully efficient.
  • Handle the appliance always with at least two persons because it is heavy.
• Installation
  • The appliance should be placed in a well-ventilated place. Ensure a space of at least 10 cm above and around the appliance.
  • Never place the appliance in a damp area or location where it might be splashed with water. Clean and dry water splashes and stains with a soft clean cloth.
  • Do not install the appliance in direct sunlight or near heat sources(e.g. stoves, heaters).
  • Install and level the appliance in an area suitable for its size and use.
  • WARNING: Keep ventilation openings in the appliance or the in-built structure clear of obstruction.
  • Make sure that the electrical information on the rating plate agrees with the power supply. If it does not, contact an electrician.
  • The appliance is operated by a 220-240 VAC/50 Hz power supply. Abnormal voltage fluctuation may cause the appliance to fail to start or damage the temperature control or compressor, or there may be an abnormal noise when operating. In such a case, an automatic regulator shall be mounted.
  • Do not use multi-plug adapters and extension cables.
  • WARNING: Do not locate multiple portable socket outlets or portable power supplies at the rear of the appliance.
  • WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
  • Do not step on the power cable.
  • Use a separate earthed socket for the power supply which is easily accessible. The appliance must be earthed.
• WARNING!
  • Only for the UK: The appliance’s power cable is fitted with a 3-cord (grounded) plug that fits a standard 3-cord (grounded) socket. Never cut off or dismount the third pin (grounding). After the appliance is installed, the plug should be accessible.
  • WARNING: Do not damage the refrigerant circuit. Daily use
  • This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.
  • Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances, but not allowed to clean and install the refrigerating appliances.
  • Keep children under 3 years of age from the appliance unless they are constantly supervised.
  • Cleaning and user maintenance shall not be done by children without supervision.
  • The appliance must be positioned so that the plug is accessible.
  • If coal gas or other inflammable gas is leaking into the vicinity of the appliance, turn off the valve of the leaking gas, open the doors and windows and do not unplug the power cable of the refrigerator/ freezer or any other appliance.
  • Notice that the appliance is set for operation at the specific ambient range between 10 and 38°C. The appliance may not work properly if it is left for a long period at a temperature above or below the indicated range.
  • Do not place unstable articles (heavy objects, containers filled with water) on top of the refrigerator/freezer, to avoid personal injury caused by falling or electric shock caused by contact with water.
  • Do not pull on the door shelves. The door may be pulled slant, the bottle rack may be pulled away, or the appliance may topple.
  • Open and close the door only with handles. The gap between the door and the cabinet is very narrow. Do not put your hands in these areas to avoid pinching your fingers. Open or close the refrigerator/ freezer doors only when no children are standing within the range of door movement.
• WARNING!
  • To avoid contamination of food, please respect the following instructions:
  • Opening the door for long periods can cause a significant increase in the temperature in the compartments of the appliance.
  • Clean regular surfaces that can come in contact with food and accessible drainage systems.
  • Clean water tanks if they have not been used for 48 hours; flush the water system connected to a water supply if water has not been drawn for 5 days.
  • Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
  • Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making ice cream and making ice cubes.
  • One-, two- and three-star compartments are not suitable for the freezing of fresh food.
  • If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould from developing within the appliance.
  • Never store bottled beer or beverages, liquids in bottles or cans (besides high percentage spirits) especially carbonated beverages in the freezer, as these will burst during freezing.
  • Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
  • Do not store medicines, bacteria or chemical agents in the appliance. This appliance is a household appliance. It is not recommended to store materials that require strict temperatures.
  • Check the condition of food if a warming in the freezer has taken place.
  • Do not set unnecessarily low temperatures in the refrigerator compartment. Minus temperatures may occur at high settings.
  • Attention: Bottles can burst
  • Do not touch frozen goods with wet hands (wear gloves). Especially do not eat ice lollies immediately after removal from the freezer compartment. There is the risk of freezing or the formation of frost blisters. FIRST aid: keep immediately under running cold water. Do not pull away!
  • Do not touch the inside surface of the freezer storage compartment when in operation, especially with wet hands, as your hands may freeze on the surface.
• WARNING!
  • Unplug the appliance in the event of a power interruption or before cleaning. Allow at least 7 minutes before restarting the appliance, as frequent starting may damage the compressor.
  • WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
• Maintenance cleaning
  • Make sure children are supervised if they carry out cleaning and maintenance.
  • Disconnect the appliance from the electrical supply before undertaking any routine maintenance. Allow at least 5 minutes before restarting the appliance, as frequent starting may damage the compressor.
  • Hold the plug, not the cable, when unplugging the appliance.
  • Do not clean the appliance with hard brushes, wire brushes, detergent powder, petrol, amyl acetate, acetone and similar organic solutions, acid or alkaline solutions. Please clean with special refrigerator/ freezer detergent to avoid damage. Eventually, use warm water and baking soda solution – about a tablespoon of baking soda to a litre/quart of water. Rinse thoroughly with water and wipe dry. Do not use cleaning powders or other abrasive cleaners. Do not wash removable parts in a dishwasher.
  • Do not scrape off frost and ice with sharp objects. Do not use sprays, electric heaters like heaters, hair dryers, steam cleaners or other sources of heat to avoid damage to the plastic parts.
  • WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard.
  • Do not try to repair, disassemble or modify the appliance by yourself. In case of repair please contact our customer service.
  • If the illuminating lamps are damaged, they must be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard.
  • Eliminate the dust on the back of the unit at least once a year to avoid hazards by fire, as well as increased energy consumption.
• WARNING!
  • Do not spray or flush the appliance during cleaning.
  • Do not use water spray or steam to clean the appliance.
  • Do not clean the cold glass shelves or glass doors with hot water. Sudden temperature changes may cause the glass to break.
  • If you leave your appliance out of use for an extended period, leave it open to prevent odour and unpleasant smells from building up inside.

Refrigerant gas information

• WARNING! The appliance contains the flammable refrigerant ISOBUTANE (R600a). Make sure the refrigerant circuit is not damaged during transportation or installation. Leaking refrigerant may cause eye injuries or ignite. If a damage has occurred, keep away open fire sources, thoroughly ventilate the room, and do not plug or unplug the power cords of the appliance or any other appliance. Inform customer service. In case of eyes come into contact with the refrigerant, rinse immediately it under running water and call immediately the eye specialist.
• WARNING: The refrigeration system is under high pressure. Do not tamper with it. Since flammable refrigerants are used, please install, handle and service the appliance strictly according to the instructions and contact the professional agent or our after-sales service to dispose of the appliance.
• WARNING! For refrigerators with ice-water function, please pay attention to the following warning: For appliances not intended to be connected to the water supply:
• WARNING: fill with potable water only. For appliances intended to be connected to the water supply:
• WARNING: connect to potable water supply only. If you want to clean the water system, please refer to the User Manual. If you have any questions, please contact the after-sales service.

Intended use

• This appliance is intended for cooling and freezing food.
• It has been designed exclusively for use in households and similar applications such as staff kitchen areas in shops, offices and other working environments; farm houses and by clients in hotels, motels and other residential type environments as well as in bed-and-breakfast and catering businesses. It is not intended for commercial or industrial use.
• Changes or modifications to the device are not allowed. Unintended use may cause hazards and loss of warranty claims.

Standards and directives

This product meets the requirements of all applicable EC directives with the corresponding harmonised standards and UK standards, which provide for CE and UKCA marking.

CAUTION!

1. When you close the door, the vertical door strip on the fridge’s left door should be bent inside (1).
2. If you try to close the left door and the vertical door strip is unbent (2), you should bend it first, otherwise the door strip will hit the fixing shaft or right door. Thus damage to the door slip or a leak will occur.  There is a heating thread inside the frame. The tem-perature of the surface will rise a little, which is normal and won’t affect the function of the appliance.

Product Description

Notice: Due to technical changes and different models, some of the illustrations in this manual may differ from your model.

Model (HCW58F18EHMP)

• A: Refrigerator compartment
  • 1 Rating plate
  • 2 Door shelf
  • 3 Cabinet shelf
  • 4 Door strip
  • 5 Water filter
  • 6 Ceiling light
  • 7 Humidity zone drawer
  • 8 Water dispenser
  • 18 Air duct
• B: Freezer compartment
  • 9 Air duct
  • 10 Ice storage bin
  • 11 Storage tray
  • 15 Storage drawer
  • 16 Adjustable feet
• C: Switch Zone compartment
  • 12 Air duct
  • 13 Storage tray
  • 14 Switch Zone storage drawer
  • 17 Adjustable feet

Control panel

Control panel (HCW58F18EHMP)

• Indicator:
  • A Fridge Compartment
  • B Switch Zone
  • C Freezer Compartment
  • D Temperature display
  • E Ice Boost
  • F Water Filter replacement Prompt
  • G Super Freeze Function
  • H Ice Maker
  • I Water On
  • J WIFI
  • K Panel lock
• Buttons:
  • L Temperature control “-”
  • M Compartment selection
  • N Temperature control “+”
  • O Super Freeze function selector
  • P Ice maker function selector
  • Q Water On function selector
  • R Wi-Fi function on/off
  • S Panel lock selector

Before first use

• Remove all packaging materials, keep them out of children`s reach and dispose of them in an environmentally friendly manner.
• Clean the inside and outside of the appliance with water and mild detergent before putting any food in it.
• After the appliance has been levelled and cleaned, wait for at least 2-5 hours before connecting it to the power supply. See Section INSTALLATION.
• Precool the compartments at high settings before loading with food. The function of Power Freeze helps to cool down the compartments quickly.
• The refrigerator temperature, Switch Zone temperature and freezer temperature are automatically set to 5° C, -18° C and -18° C respectively. These are the recommended settings. If desired, you can change these temperatures manually.
• Please see ADJUST THE TEMPERATURE.

Use

• Before first using the Ice and Water or Automatic Ice function
  • Before first use, you need to flush water through the filter to remove impurities or trapped air in the water tank and filter system.

For Ice and Water

• Press the water dispenser pedal to dispense 4L of wa- ter – wait for 4 minutes before dispensing again.
• Dispense 4L of water and then wait for another 4 minutes – There may be carbon residue dispensed together with water. This is not harmful and normal during the flushing process.
• Dispense another 4 L of water. – This prevents excessive dripping of water from your dispenser.
• There may be a few drips of water coming out of the dispenser for a few days after installation. This is to clear the remaining trapped air in the dispen- ser.
• Ensure your refrigerator has cooled for at least 2 hours before use.

For the Automatic Ice model

1. Press the control panel button “p” to turn on the ice maker function.
2. Discard the first full bin of the ice box. Clean the ice box with water and install it back. Your ice maker is now ready for use.
3. Repeat step 2 to remove dust in the ice tray collected during manufacture and transport.
4. Empty the water, dry the bin and return it correctly.
5. Once your Ice maker is turned on the first bin of ice may be discoloured. This is not harmful and normal during the flushing process. Discard the first full bin of ice made. Your Ice maker is now ready for use.

Notice: The performance of your water filter will increase with use, reaching optimum performance after two to three full bins of ice.

Sensor keys
The buttons on the control panel are sensor keys, which already respond when lightly touched with the finger.

Switch on /off the appliance
The appliance is in operation as soon as it is connected to the power supply. When the refrigerator is first powered on, the indicator “D” (Temperature display) illuminates. The fridge temperature, Switch Zone temperature and freezer temperature are automatically set to 5° C, -18° C and -18° C respectively. Maybe the panel lock is active.

Notice

• The appliance is preset to the recommended temperature of 5°C (refrigerator),-18°C(Switch Zone)and – 18°C (freezer).
• Under normal ambient conditions, you need not set a temperature.
• When the appliance is switched on after disconnection from the main power supply, it may take up to 12 hours for the correct temperatures to be reached.
• Empty the appliance before switching off. To switch off the appliance, pull the power cord out of the power socket.

Lock/unlock panel

The display screen turns off automatically 30 seconds after pressing a key. The display will be automatically locked. It lights up automatically when pressing any key or opening any door.

Notice
Fridge temperature, Switch Zone temperature, Freezer temperature, Super Freeze function, Ice maker function, function water, and Wi-Fi function can‘t be adjusted under the lock state.

Standby-mode

• The display screen turns off automatically 30 seconds after pressing a key. The display will be automatically locked. It lights up automatically by touching any key or opening the door.(The alarm does not light up the display screen)

Manual adjusting mode

• If you want to manually adjust the temperature of the appliance,you can set the temperature adjust button (refer to ADJUST THE TEMPERATURE)

Adjust the temperature
The indoor temperatures are influenced by the following factors:

• Ambient temperature
• Frequency of door opening
• Amount of stored foods
• Installation of the appliance

Door alarm
The door alarm will trigger when the door opens for a long time or is not closed properly, as a reminder.

Adjust the temperature of Fridge

Unlock the settings by long pressing key “S” for 3 seconds. Under unlock state, press key “M”(Compartment selection ) to toggle across compartments. When indicator “A” (Fridge compartment indicator) lights up, press key “L” (Temperature control “-”) or key “N” (Temperature control “+”) to adjust the fridge compartment temperature. The value displayed on indicator “D” decreases by 1 °C when key “L” is pressed each time.

The display flashes and turns solid with the set temperature, then goes off after a few seconds. Accordingly, the value displayed on indicator “D” increases by 1 °C when the key “N” is pressed each time. The display flashes and turns solid with the set temperature, then goes off after a few seconds. Fridge compartment temperature can be adjusted from 1 °C to 9°C with 1°C incremental.

Notice: Fridge temperature can‘t be adjusted under lock state.

Adjust the temperature for the Freezer
Unlock the settings by long pressing key “S” for 3 seconds. Under unlock state, press key “M” (Compartment selection) to toggle across compartments.When indicator “C” (Freezer Compartment indicator)  lights up, press key “L” (Temperature control “-”)or key “N” (Temperature control “+”) to adjust the Freezer compartment temperature. The value displayed on indicator “D” decreases by 1 °C when key “L” is pressed each time. The display flashes and turns solid with the set temperature, then goes off after a few seconds. Accordingly, the value displayed on indicator “D” increases by 1 °C when key “N” is pressed each time. The display flashes and turns solid with the set temperature, then goes off after a few seconds. Freezer compartment temperature can be adjusted from -14 °C to -24 °C with 1 °C incremental.

Notice: Freezer temperature can‘t be adjusted under Super Freeze and lock state.

Adjust the Switch Zone temperature
Unlock the settings by long pressing key “S” for 3 seconds. Under unlock state, press key “M” (Compartment selection) to toggle across compartments. When indicator “B” (Switch Zone indicator) lights up, press key “L” (Temperature control “-”) or key “N“(Temperature control “+”) to adjust Switch Zone compartment temperature. The value displayed on indicator “D” decreases by 1 °C when key “L” is pressed each time. The display flashes and turns solid with the set temperature, then goes off after a few seconds. Accordingly, the value displayed on indicator “D” increases by 1 °C when key “N” is pressed each time. The display flashes and turns solid with the set temperature, then goes off after a few seconds. Switch Zone compartment temperature can be adjusted from 5 °C to -18 °C with 1 °C incremental.

Notice: Switch Zone temperature can‘t be adjusted under lock state.

Super Freeze function
Super Freeze function can freeze the fresh food as soon as possible to the core by accelerating the freezing to preserve the best nutritional value, appearance and taste of food. If you need to freeze a large amount of food once, it is recommended to set the Super Freeze function on ahead for 24 hours before the usage of the freezer compartment. Unlock the settings by long pressing key “S” for 3 seconds. Under the unlocked state, press key “O” (Super Freeze function selector), indicator “G” (Super Freeze function indicator) lights up, product enters Super Freeze mode. The product automatically exits Super Freeze mode after 50 hours of activation. For manually exiting Super Freeze mode, press key “O” (Super Freeze function selector) under unlock state, indicator “G” (Super Freeze function indicator) goes off, product exits Super Freeze mode.

Notice: Under Super Freeze mode, key “L” (Temperature control “-”) & key “N”(Temperature control “+”) are locked when the freezer compartment is selected and the freezer compartment temperature cannot be adjusted.

Ice maker
Under unlock state, press key “P” (Ice maker selector), indicator “H” (Ice maker indicator) lights up, product enters Ice maker mode. To exit Ice maker mode, press key “P” (Ice maker selector) under unlock state, indicator “H” (Ice maker indicator) goes off, product exits Ice maker mode.

Notice: The ice maker is off by default when the refrigerator is powered on for the first time. The ice maker is designed to automatically dispense ice into the ice storage bin and it will stop when it detects the bin is full. The more ice you use, the more ice it makes.

3 Sec.Ice Boost
Under unlocked state, press key “P”(Ice maker selector) for 3 seconds, indicator “H”(Ice maker indicator) and indicator “E”(Ice Boost indicator) light up, and the Ice Boost function is enabled. In the unlock state and under the Ice Boost function, press key “P” (Ice maker selector) for 3 seconds, after hearing one beeping sound, Indicator “E”(Ice Boost indicator) goes off, product exits the Ice Boost function. The ice maker indicator “H” still lights up, with the Ice maker function still activated.

Notice: If the Ice maker is enabled before entering the Ice Boost function. When the product exits the Ice Boost function, the Ice maker indicator “H” still lights up and the Ice maker is still working normally; If the ice maker is disabled before entering the Ice Boost function, when the product exits the Ice Boost function, the Ice maker indicator “H” goes off and the ice maker stops working as well.

Water filter function: After 6 months since the product was powered on for the first time, indicator “F” (Water Filter replacement Prompt indicator) lights up as a reminder to replace the water filter. After replacing the water filter, press the key “Q” (Water On function selector) for 3 seconds, after hearing a beeping sound, indicator “F” (Water Filter replacement Prompt indicator) goes off, and the Water Filter replacement Prompt function is reset.

Function water: In unlock state, press key “Q”(Water on function selector), after hearing one beeping sound, the indicator “I” (Water on indicator) lights up, function water is enabled, water will come out from the dispenser when you push the pedal. Press the key “Q” (Water on function selector) again, and the indicator “I” (Water on indicator) goes off, function water is disabled, and water will not come out from the dispenser when you push the pedal.

Notice
If the fridge compartment’s right door is open, water will not dispense when the pedal is pressed, even when the function water is enabled.

Wi-Fi mode setting

IN-APP PAIRING PROCEDURE

1. Follow in app instructions to configure the Wi-Fi. Press the Wi-Fi key “R” for 3 seconds and the Wi-Fi icon “J” starts blinking quickly to activate the Wi-Fi model.
2. Once the Wi-Fi is configured and the connection is established, the Wi-Fi icon “J” is on and fixed.
3. To turn off the Wi-Fi function, press the key “R” once and the Wi-Fi icon “J” turns off.

Notice

1. To reconfigure Wi-Fi function, Press Wi-Fikey “R” for 3 seconds, the Wi-Fi icon blinks quickly and enters the configuration mode
2. If the product has been configured and the Wi-Fi function was turned off, the refrigerator will not enter the configuration mode once it is reconnected to the power.

Notice

1. This product is not intended for commercial use.
2. Transmitter working frequency:2400 MHz~2483.5MHz
3. Transmitter maximum output power:2.4GHz Wi-Fi: 16dBm; Bluetooth LE: 5dBm;Bluetooth(BR/EDR): 10dBm.

Notice

1. To turn off the Wi-Fi, press the Wi-Fi key “R” and the Wi-Fi icon “J” turns off.
2. To turn on the Wi-Fi and start the configuration, press the Wi-Fi key “R” and the Wi-Fi icon “J” starts blinking slowly. If want to turn off the Wi-Fi function, press the key “R” once. If want to configure the Wi-Fi function, press the key “R” for 3 sec but less than the 20s, and an acoustic signal is made, the Wi-Fi icon blinks quickly and enters the configuration mode. The above steps are repeated.
3. If the product has been configured and the Wi-Fi function was turned off, the refrigerator will not enter the configuration mode once it is reconnected to the power.
4. Once the Wi-Fi is configured and the connection is established, the Wi-Fi icon “J” is on and fixed.

Door alarm
The door alarm will trigger when the door opens for a long time or is not closed properly, as a reminder.

• REFRIGERATOR DOOR FOR LEFT
• REFRIGERATOR DOOR FOR RIGHT
• FREEZER DOOR
• SWITCH ZONE DOOR

Water dispenser
With the water dispender cool drinking water can be tapped.

Getting water from the dispenser

1. Place a glass underneath the water outlet.
2. Push it gently against the water dispenser lever. Make sure the glass is in line with the dispenser to prevent the water from splashing out.
3. Water in the tray(B) should be removed in time, as it could overflow when the door opens and closes.

Ice maker instructions

• WAR NING!
  • Connect to potable water supply only.
  • Connecting the water line must only be installed by a qualified plumber and by local legislation and regulations governing water quality.
• Notice
  • This water line installation is not covered by the appliance warranty.

Connecting water to the appliance

1. Remove the rubber plug (1) from the water inlet valve.
2. Firmly push the water tube onto the water inlet valve and tighten up the collar nut. This water pipe needs to be cut from the middle and used, and the other section is used as a spare part.

Connecting to the water tap
This feature is only available on some models.

1. Push the water tube into the hole of the tap connector supplied in the accessories. The pipe should be held firmly whilst the connector is pushed onto the pipe.
2. Ensure that the rubber washer is fitted to the inside of the tap connector before screwing it onto the tap.
   • A separate connector or adaptor may need to be purchased if your tap fitting does not match the thread size of the connector provided.

Checking the Water Connection
This feature is only available on some models.

• Turn on the water supply and switch on the appliance. Carefully check all fittings for possible leaks due to poorly fitted hoses.
• Press and hold the 3Sec.Filter the Reset button for three seconds. The new water filter has been activated.
• Place a cup under the water dispenser to verify that water is flowing through the appliance.
• Check the connecting tube and joints for leaks once again.

Replacing the water filter

1. Uplift the water filter cover.
2. Remove the disposable water filter.
3. Replace with a new water filter. Insert the new filter into the filter head and rotate it clockwise until the arrow on the new filter lines up with the arrow on the filter head. Swing the filter back into the compartment.
4. Close the water filter cover.
5. Press and hold the 3Sec.Filter the Reset button for 3 seconds.
6. Dispense water for approximately 5 minutes to remove trapped air and contaminants

CAUTION! Failure to replace filters when required or using non-Haier authorised water filters can cause the filter cartridge to leak and result in property damage.

Model: Haier HRXWF

• System certified by IAPMO R&T against NSF/ANSI Standards 42, 53, 401 and P473 for the reduction of claims specified on the performance data sheet and at the airport. org.
• Actual performance may vary with local water conditions.

Application Guidelines/Water Supply Parameters

• Service Flow: 0.5 gpm (1.89 pm)
• Water Supply: Potable Water
• Water Pressure: 25-120 psi (172-827 kPa)
• Water Temperature: 33°F-100°F (0.6°C-38°C)
• Capacity: 170 gallons (643.5 liter)

Tips on storing fresh food Storing in the refrigerator compartment

• Keep your fridge temperature below 5°C.
• Hot food must be cooled to room temperature before storing in the appliance.
• Foods stored in the refrigerator should be washed and dried before storing Food to be stored should be properly sealed to avoid odour or taste alterations.
• Do not store excessive quantities of food. Leave spaces between foods to allow cold air to flow around them, for better and more homogeneous cooling.
• Foods eaten daily should be stored at the front of the shelf.
• Leave a gap between foods and the inner walls, allowing air to flow. Especially don’t store foods against the rear wall: foods could freeze against the rear wall. Avoid direct contact of food (especially oily or acidic food) with the inner liner, as oil/acid can erode the inner liner. Clean away oily/acid dirt whenever it is found.
• Defreeze frozen food in the fridge storage compartment. This way, you can use the frozen food to decrease the temperature in the compartment and save energy.
• The ageing process of fruits and vegetables such as courgettes, melons, papaya, bananas, pineapple, etc. can be accelerated in the refrigerator. Therefore, it is not advisable to store them in the refrigerator. However, the ripening of strongly green fruits can be promoted for a certain period. Onions, garlic, ginger and other root vegetables should also be stored at room temperature.
• Unpleasant odours inside the fridge are a sign that something has spilled and cleaning is required. See CARE AND CLEANING.
• Different foods should be placed in different areas according to their properties:

Notice: Please keep a distance of more than 10 mm between the food placed and the air duct or sensors to ensure the cooling effect.

1. Butter, cheese, etc.
2. Eggs, cans, canned food, spices, etc.
3. Drinks and bottled foods.
4. Pickled foods, canned food, etc.
5. Meat products, snack foods, pasta, canned food, milk, tofu, dairy etc.
6. Cooked meat, sausages, etc.
7. Humidity zone drawer: Fruit, vegetables, salad, etc.

Storage in the Switch Zone compartment
Switch Zone compartment allows you to adjust the temperature between – 18 C to 5 C according to the demand for food storage and provides you with further flexibility in storage options for your convenience.

Storage in the freezer compartment

• Keep the freezer temperature at – 18°C. 24 hours before freezing switch on the Super-freeze function; -for small quantities of food 4-6 hours are sufficient.
• Hot food must be cooled to room temperature before storing in the freezer compartment.
• Food cut into small portions will freeze faster and be easier to defrost and cook. The recommended weight for each portion is less than 2.5 kg
• It is better to pack food before putting it into the freezer. The outside of the packaging must be dry to avoid bags sticking together. Packaging materials should be odour-free, airtight, non-poisonous and nontoxic.
• To avoid the expiration of storage periods, please note the freezing date, time limit and name of the food on the packaging according to the storage periods of different foods.
• WARNING: Acid, alkali salt etc. could erode the internal surface of the freezer.
• Do not place the food having these substances (e.g. sea fish) directly on the internal surface. Saltwater in the freezer should be cleaned up immediately.
• Do not exceed the food storage times recommended by the manufacturers. Only take the required amount of food out of the freezer.
• Consume defrosted food quickly. Defrosted food cannot be re-frozen unless it is first cooked, otherwise, it may be edible.
• Do not load excessive quantities of fresh food in the freezer compartment. Refer to the freezing capacity of the freezer – See TECHNICAL DATA or data at the type plate.
• Food can be stored in the freezer at a temperature of at least – 18°C for 2 to 12 months, depending on its properties (e.g.. meat: 3-12 months, vegetables: 6-12 months)
• When freezing fresh food, avoid bringing it in contact with already frozen food. Risk of thawing!

When storing commercially frozen foods, please follow these guidelines:

• Always follow manufacturers’ guidelines for the length of time you should store food. Do not exceed these guidelines!
• Try to keep the length of time between purchase and storage as short as possible to preserve food quality.
• Buy frozen foods, which have been stored at a temperature of -18 °C or below.
• Avoid buying food that has ice or frost on the packaging – This indicates that the products might have been partially defrosted and refrozen at some point temperature rises affect the quality of food.

Notice: Please keep a distance of more than 10 mm between the food placed and the air duct to ensure the cooling effect.

Equipment

Multi-air-flow

• The refrigerator is equipped with a multi-air-flow system, with which cool air flows are located on every shelf level.
• This helps to maintain a uniform temperature to ensure that your food is kept fresher for longer.

Adjustable shelves
The height of the shelves can be adjusted to fit your storage needs.

1. To relocate a shelf, remove it first by uplifting its hind edge (1) and pulling it out (2)
2. To reinstall it, put it on the lugs on both sides and push it to the most rearward position until the rear of the shelf is fixed inside the slots in the sides.

Notice: Ensure that all ends of a shelf are level.

Humidity zone drawer

In this compartment, the humidity level is around 85%. It is controlled automatically by the system and is suitable for storing fruits, vegetables, salads etc.

Notice:

• Do not remove the plastic cover inside the two zones. They maintain the humidity.
• Cold-sensitive fruits like pineapple, avocado, bananas. grapefruits and vegetables such as potatoes, aubergines, beans, cucumbers, zucchini tomatoes and cheese should not be stored in these two drawers.

Removable door shelves

• The door racks can be removed for cleaning: Place hands on each side of the rack, lift it upwards (1) and pull it out (2).
• To insert the door rack, the above steps are carried out in reverse order.

Removable freezer drawer

• Tent 1, and remove 2, and pull out to the maximum exporter to insert the drawer, the above steps are carried out in reverse order.

OPTIONAL: OK-temperature indicator

• The OK-temperature indicator can be used to determine temperatures below + 4°C. Gradually reduce the temperature if the sign does not indicate OK”.

The Light
The LED interior light comes on when the door is opened and it will automatically go off if the door is left open for more than 7 minutes. The performance of the lights is not affected by any of the appliance’s other settings.

Energy saving tips

• Make sure the appliance is properly ventilated (see INSTALLATION).
• Do not install the appliance in direct sunlight or near heat sources (e.g. stoves, heaters).
• Avoid unnecessarily low temperatures in the appliance. The energy consumption increases the lower the temperature in the appliance is set.
• Functions like Super-Freeze consume more energy.
• Allow warm food to cool down before placing it in the appliance.
• Open the appliance door as little and as briefly as possible.
• Do not overfill the appliance to avoid obstructing the airflow.
• Avoid air within the food packaging.
• Keep door seals clean so that the door always closes correctly.
• Defreeze frozen food in the fridge storage compartment.
• The most energy-saving configuration requires the appliance to keep drawers, food boxes and shelves in factory-fresh condition, and food should be placed as far as possible without blocking the air outlet of the duct.

Care and cleaning

WARNING! Disconnect the appliance from the power supply before cleaning.

Cleaning

• Clean the appliance when only little or no food is stored.
• The appliance should be cleaned every four weeks for good maintenance and to prevent bad stored food odours.

WARNING:

• Do not clean the appliance with hard brushes, wire brushes, detergent powder, petrol, amyl acetate, acetone and similar organic solutions, acid or alkaline solutions. Please clean with special refrigerator detergent to avoid damage.
• Do not spray or flush the appliance during cleaning.
• Do not use water spray or steam to clean the appliance.
• Do not clean the cold glass shelves with hot water. Sudden temperature changes may cause the glass to break.
• Do not touch the inside surface of the freezer storage compartment, especially with wet hands, as your hands may freeze on the surface.
• In case of heating check the condition of frozen goods.
• Always keep the door gasket clean.
• Clean the inside and housing of the appliance with a sponge dampened in warm water and neutral detergent.

1. Please scrub the interior and exterior of the refrigerator, including door sealing, door rack, glass shelves, boxes and so on, with a soft towel or sponge dipped in warm water (you may add neutral detergent into the warm water).
2. If there is liquid spilled, remove all the contaminated parts, directly rinse with the flow water, dry and place it back into the fridge.
3. If there is spilled cream (such as the cream, melting ice cream), please remove all the contaminated parts, put them into the warm water at about 40 °C for some time, then rinse with the flowing water, dry and place it back into the fridge.
4. In case some small part or component gets stuck inside the fridge (between shelves or drawers), use a small soft brush to release it. If you cannot reach the part, please contact Haier service
   • Rinse and dry with a soft cloth.
   • Do not clean any of the parts of the appliance in a dishwasher.
   • Allow at least 5 minutes before restarting the appliance as frequent starting may damage the compressor.

Defrosting

• The defrosting of the fridge and the freezer compartment is done automatically; no manual operation is needed.

Replacing the LED-lamps

• Replaceable (LED only) light source by a professional

This product contains a light source of energy efficiency class G.

Non-use for a longer period

• If the appliance is not used for an extended period, and you will not use only the
• Holiday function or the fridge function for the refrigerator:
• Take out the food.
• Unplug the power cord.
• Empty and clean the water
• Clean the appliance as described above.
• Keep the doors open to prevent the creation of bad odours inside.

Notice

• Turn the appliance off only if strictly necessary.

Moving the appliance

1. Remove all food and unplug the appliance.
2. Secure shelves and other moveable parts in the fridge and the freezer with adhesive tape.
3. Do not tilt the refrigerator more than 45° to avoid damaging the refrigerating system.

WARNING!

• Do not lift the appliance by its handles.
• Never place the appliance horizontally on the ground

Cleaning the ice cube tray

1. Turn off the icemaker function via the display panel, hold down the handle of the icemaker, and use strength to pull out the icemaker.
2. Remove the icemaker assembly from the refrigerator and turn over the icemaker, so that the ice cube tray is visible.
3. Pull the oval-shaped fastener on the ice tray in the direction of arrow 1. Tilt the ice tray upward and pull it out in the direction of arrow 2.
4. After cleaning the tray, put it back in, then firmly push in the icemaker, close the freezer drawer, and switch on the icemaker function via the display panel.

Icemaker usage precautions

• For newly installed appliances, you should wait for 24 hours. This will enable the freezer compartment to cool down so that it can make ice.
• The ice machine will make 8 ice cubes each time; but the specific ice-making quantity will depend on the indoor temperature, frequency that the doors are opened, water pressure, freezer compartment temperature, etc.
• To ensure that the ice tray gets filled up with ice cubes, the ice tray should be frequently pulled out so that the ice cubes get evenly distributed.
• It is a normal phenomenon that some of the ice cubes will clump together during removing.
• When the freezer compartment reaches or is below-8 °C, the icemaker will start making ice (if you are just beginning to use the icemaker, or it has not been used to make ice in a long time, you should discard the first several ice cubes, so that impurities in the water l ine get run out.)
• The icemaker must be installed in the refrigerator through an authorized service agency.
• NEVER expose the water pipe to temperatures below 0°C to avoid freezing.
• Test the tubing for leaks by flushing the tube through with water, until the water runs clear.
• After the appliance has been sited into the location of your choice, make sure that the water tube is arranged so it does not incur damage through bends and kinks and is clear of any heat sources.
• Once the temperature inside the freezer is at -8°C ice production will begin.
• DO NOT touch the ice cube outlet with your hands, or any implements to avoid injury or damage.
• DO NOT manually add water – this is an automatic water system. If the ice maker is turned on but the appliance is not connected to water, the ice maker will not work。

If you occasionally hear unusual sounds in the refrigerator

• You may occasionally hear some “crunching” sounds, but these are just normal sounds that are emitted during ice-making, so do not worry.

If you do not often use ice cubes

• “Old” ice cubes will become cloudy, and will not taste fresh; therefore, please periodically clean the ice cube tray and wash it out with warm water.
• Before replacing the ice cube tray, be sure to cool it down, otherwise, ice will stick to other parts of the ice machine and affect the ice-making function.

If the ice maker in the freezer compartment is not used for a long time

• If not used for a long time, please remove the automatic icemaker and any residual ice cubes in the ice storage compartment, wash the ice cube tray and the ice storage compartment with warm water, wipe them dry with a clean towel and put them somewhere else in order to increase storage space.
• The water reservoir should be removed, any residual water should be drained out.

If the ice maker in the freezer compartment is not used for a long time

• The ice-making capacity is 0.8kg/24 hours(this figure is the test result in the lab under the 25°C ambient temperature condition). During the daily use of the appliance, due to the different ambient temperatures and water pressure, the ice-making capacity may differ a little.
• Do not store ice cubes, which are produced during the first batch of cubes following appliance start-up, or after a prolonged break. Discard these cubes.
• To allow the ice cube tray to fill to maximum capacity, you will need to manually arrange the ice cubes periodically.
• Some ice cubes may stick together when dropped into the storage box – you will need to separate these to allow maximum use of the icebox.
• Throw out the first few batches of ice cubes if you are making ice for the first time or have not made it for a long time.
• If the cubed ice becomes smaller, this may suggest that the filter is blocked from the impurities.

Troubleshooting

Many occurring problems could be solved by yourself without specific expertise. In case of a problem please check all shown possibilities and follow the below instructions before you contact an after-sales service. See CUSTOMER SERVICE.

WARNING!

▶ Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.

▶ Electrical equipment should be serviced only by qualified electrical experts because improper repairs can cause considerable consequential damages.

▶ A damaged supply should only be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard.

Problem| Possible Cause| Possible Solution
The compressor does not work.| • The mains plug is not connected to the mains socket.

•      The appliance is in the defrosting

cycle

| •      Connect the mains plug.

•      This is normal for an automatic defrosting

The appliance runs frequently or runs for a too long period.| •      The indoor or outdoor temperature is too high.

•      The appliance has been off power for some time.

•      A door of the appliance is not tightly closed.

•      The door has been opened too frequently or for too long.

•      The temperature setting for the freezer compartment is too low.

•      The door gasket is dirty, worn, cracked or mismatched.

•      The required air circulation is not guaranteed.

| •      In this case, it is normal for the

appliance to run longer.

•      Normally, it takes 8 to 12 hours for the appliance to cool down completely.

•      Close the door/drawer and ensure the appliance is located on level ground and no food or container is jarring the door.

•      Do not open the door/drawer too frequently.

•      Set the temperature higher until a satisfactory refrigerator temperature is obtained. It takes 24 hours for the refrigerator temperature to become stable.

•      Clean the door/drawer gasket or replace them with customer service.

•      Ensure adequate ventilation.

The inside of the frigerator is dirty and/ or smells.| •      The inside of the refrigerator needs cleaning.

•      Food of strong odour is stored in the refrigerator.

| •      Clean the inside of the refrigerator.

•      Wrap the food thoroughly.

high.

• Too-warm goods have been stored.

•      Too much food has been stored at one time.

•      The goods are too close to each other.

•      A door/drawer of the appliance is not tightly closed.

•      The door/drawer has been opened too frequently or for too long.

| •      Reset the temperature.

•      Always cool down goods before storing them.

•      Always store small quantities of food.

•      Leave a gap between several foods allowing air to flow.

•      Close the door/drawer.

•      Do not open the door/drawer too frequently.

It is too cold inside

the appliance.

| •      The temperature is set too low.

•      The Super-Frz/Super-Coolfunc- tion is activated or is running too long.

| •      Reset the temperature.

•      Switch off the Super-Frz/Su- per-Cool function

Moisture formation on the inside of the refrigerator compartment.| •      The climate is too warm and too-

damp.

•      A door/drawer of the appliance is not tightly closed.

•      The door/drawer has been opened too frequently or for too long.

•      Food containers or liquids are left open.

| •      Increase the temperature.

•      Close the door/drawer.

•      Do not open the door/drawer too frequently.

•      Let hot foods cool to room temperature and cover foods and liquids.

Moisture accumulates on the refrigerator’s outside surface or between the doors/door and drawer.| •      The climate is too warm and too

damp.

•      The door is not closed tightly. The cold air in the appliance and the warm air outside it condensates.

| •      This is normal in a damp climate and will change when the humidity decreases.

•      Ensure that the door/drawer is tightly shut.

Strong ice and frost in the freezer compartment.| •      The goods were not adequately packaged.

•      A door/drawer of the appliance is not tightly closed.

•      The door/drawer has been opened too frequently or for too long.

•      The door/drawer gasket is dirty, worn, cracked or mismatched.

•      Something on the inside prevents the door/drawer from closing properly.

| •      Always pack the goods well.

•      Close the door/drawer.

•      Do not open the door/drawer too frequently.

•      Clean the door/drawer gasket or replace them with new ones.

•      Reposition the shelves, door racks, or internal containers to allow the door/drawer to close.

normal.
The appliance makes abnormal sounds.| •      The appliance is not located on level ground.

•      The appliance touches some object around it.

| •      Adjust the feet to level the appliance.

•      Remove objects around the appliance.

A slight sound is to be heard similar to that of flowing water.| •      –| • This is normal.
You will hear an alarm beep.| •      The fridge storage compartment door is open.| •      Close the door.
You will hear a faint hum.| •      The anti-condensation system is

working

| •      This prevents condensation

and is normal

The interior lighting or cooling system does not work.| • The mains plug is not connected to the mains socket.

•      The power supply is not intact.

•      The LED lamp is out of order.

| •      Connect the mains plug.

•      Check the electrical supply to the room. Call the local electricity company!

•      Please call the service to change the lamp.

To contact technical assistance, visit our website: https://corporate.haier- europe.com/en/. Under the section “Website”, choose the brand of your product and your country. You will be redirected to the specific website where you can find the telephone number and form to contact technical assistance.

Power interruption

In the event of a power cut, food should remain safely cold for about 5 hours. Follow these tips during a prolonged power interruption, especially in summer:

• Open the door/drawer as few times as possible.
• Do not put additional food into the appliance during a power interruption.
• If prior notice of a power interruption is given and the interruption duration is longer than 5 hours, make some ice and put it in a container on top of the refrigerator compartment.
• An inspection of the goods is required immediately after the interruption.
• As the temperature in the refrigerator rises during a power interruption or other failure, the storage period and edible quality of food will be reduced. Any food that defrosts should be either consumed or cooked and refrozen (where suitable) soon afterwards to prevent health risks.

Memory function during power interruption
After the restoration of power, the appliance continues with the settings that were set before the power failure.

Installation

Unpacking

WARNING! The appliance is heavy. Always handle with at least two persons. Keep all packaging materials out of children´s reach and dispose of them in an environmentally friendly manner.

• Take the appliance out of the packaging.
• Remove all packaging materials.

Environmental conditions
The room temperature should always be between 10° C and 38° C since it can influence the temperature inside the appliance and its energy consumption. Do not install the appliance near other heat-emitting appliances (ovens, refrigerators) without isolation.

Space requirement

• Required space when the door is opened:
  • W1=1076 mm
  • W2=1360 mm
  • D1=628 mm
  • D2=1064mm

Ventilaton cross-section

To achieve sufficient ventilation of the appliance for safety reasons, the information on the required ventilation cross sections must be observed.

Aligning the appliance
The appliance should be placed on a flat and solid surface.

1. Tilt the refrigerator slightly backwards.
2. Set the feet to the desired level.

Make sure the distance to the wall on the hinge side is at least 10 cm for the door to open properly.

Notice: For a free-standing appliance: this refrigerating appliance is not intended to be used as a built-in appliance.

1. The stability can be checked by alternately bumping on the diagonals. The slight swaying should be the same in both directions. Otherwise, the frame can warp; possible leaking door seals are the result. A low tendency to the rear facilitates the closing of the doors.

Fine-tuning of the doors

• If the doors are not on one level, this mismatch can be remedied by the following:

Using adjustable foot

• Rotate the adjustable foot according to the direction of the arrow to turn up or down the foot. Contact after-sale service if needed.

Notice: In the future use of refrigerator, doors uneven phenomenon may occur to the weight of stored food. Then please adjust according to the above methods.

Waiting time
To the maintenance-free lubrication oil is located in the capsule of the compressor. This oil can get through the closed pipe system during slanting transport. Before connecting the appliance to the power supply you have to wait at least 2 hours so that the oil runs back into the capsule.

Electrical connection

• Before each connection check if:
  • power supply, socket and fusing are appropriate to the rating plate.
  • the power socket is earthed and no multi-plug or extension.
  • the power plug and socket are strictly according.
  • Connect the plug to a properly installed household socket.

WARNING! To avoid risks a damaged power cord must be replaced by customer service (see warranty card).

Ice and Water

• Your Ice and Water and Automatic ice refrigerator must be installed by a qualified plumber or Haier-trained and supported service technician as incorrect plumbing can lead to water leaks.
• Haier Appliances does not accept responsibility for damage (including water damage) caused by faulty installation or plumbing.

WARNING!

• Only connect to drinking water supply. The water filter only filters impurities in the water and makes ice clean and hygienic. It cannot sterilize or destroy germs or other harmful substances.
• Too high water pressure in the hose can damage the appliance. Install a pressure reducer when the water pressure in the hose exceeds 0.6 MPa.
• Before connection, check whether the water is clean and clear.

Notice: Water connection

• The pressure of the cold water has to be 0.15-0.6 MPa.
• The maximum permitted length of water hose is 8 metres. Longer hoses will affect the ice cubes and cold water content.
• The ambient temperature has to be 0°C minimum.
• Keep the water hose away from heat sources.

1. Connect the end of the pipe (B2) to one of the adapters “D” suited to the water main.
2. Connect the end of B1 to the valve assembly at the back of the appliance.
3. Open the water tab to check if the system is leak-free and flush the pipe.

WARNING! Ensure always that the connections are firm, dry and leak-free! Take care the hose never to be crushed, kinked, or twisted

Technical data

Product fiche according to regulation EU No. 2019/2016

C(38)
Temperature rise time (h)| 9
Ice making capacity| 0.8kg/24h
Type of appliance| freestanding
Others| –

Explanations: Yes, featured

1. Based on the results of the standards conformance test over 24 hours. The actual consumption depends on the use and the location of the appliance.
2. Climate rating SN: This appliance is intended for use in an ambient temperature of between + 10°C and +32°C
   • Climate rating N: This appliance is intended for use in an ambient temperature of between + 16°C and +32°C
   • Climate rating ST: This appliance is intended for use in an ambient temperature of between + 16°C and +38°C
   • Climate rating T: This appliance is intended for use in an ambient temperature of between + 16°C and +43°C

Additional technical data

Customer service

We recommend our Haier Customer Service and the use of original spare parts. If you have a problem with your appliance, please first check the section TROUBLESHOOTING.

If you cannot find a solution there, please contact

• your local dealer or
• our European Call Service Centre (see listed phone numbers below) or
• the Service & Support area at www.haier.com. where you can activate the service
• claim and also find FAQs.
• To contact our Service, ensure that you have the following data available.
• The information can be found on the rating plate.
  • Model _____
  • Serial No. _____
• Also, check the Warranty Card supplied with the product in case of warranty.

European Call Service-Center

Country*| Phone number| Costs
Haier Italy (IT)| 199 100 912|
Haier Spain (ES)| 902 509 123|
Haier Germany (DE)| 0180 5 39 39 99| •      14 Ct/Min Landline

•      max 42 Ct/Min Mobile

Haier Austria (AT)| 0820 001 205| •      14,53 Ct/Min Landline

•      max 20 Ct/Min all others

Haier United Kingdom (UK)| 0333 003 8122|
Haier France (FR)| 0980 406 409|

• For other countries please refer to www.haier.com.
• Haier Europe Trading S.r.l
• Branch UK
• Westgate House, Westgate, Ealing
• London, W5 1YY

Duration of the guarantee of the refrigerating appliance:

• The minimum guarantee is 2 years for EU Countries, 3 years for Turkey, 1 year for UK, 1 year for Russia, 3 years for Sweden, 2 years for Serbia, 5 years for Norway, 1 year for Morocco, 6 months for Algeria, Tunisia no legal warranty required.

The period of spare parts for the repair of the appliance:

• Thermostats, temperature sensors, printed circuit boards and light sources are available for a minimum period of seven years after placing the last unit of the model on the market.
• Door handles, door hinges, trays and baskets for a minimum period of seven years and door gaskets for a minimum period of 10 years, after placing the last unit of the model on the market.
• For further information about the product, please consult https://eprel.ec.europe.eu/. or scan the QR on the energy label supplied with the appliance.
• Haier Smart Home Co., Ltd.
• No.1 Haier Road, Haier Industry Park, Hi-Tech Zone,
• 266103 Qingdao, Shandong, China
• MADE IN CHINA

WARNING: Risk of fire/flammable material. The symbol indicates there is a risk of fire since flammable materials are used. Take care to avoid causing a fire by inviting flammable material.

References

• Choose your country or region - Haier
• Choose your country or region - Haier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>