MONACOR ELAX-2000BX ECO Line User Guide
- June 7, 2024
- MONACOR
Table of Contents
ELAX-2000BX
∨Bestell-Nr. • Order No. 0180156
Additional Information:
Setting the Signal Format
Use the control buttons on the rear side of the camera ELAX-2000BX to set the
signal format for the video output: Keep the corresponding button pressed for
approx. 5 seconds until the camera image on the display briefly goes dark.
| Button | Signal format |
|---|---|
| <L | CVBS |
| >R | AHD |
| ∧U | HD-CVI |
| ∨D | HD-TVI |
Then the image will be shown in the signal format selected. For any other
settings, use the OSD menu of the camera; it can, for example, be called up by
means of the center control button E.
Subject to technical modification.
4-in-1
1080P HD CCTV Camera
ELAX-2000BX
ELAX-2036BF
ELAX-2036DF
ELAX-2037PIR
ELAX-2812BV
ELAX-2812DV
ELAX-2812DVS
AHD • FBAS • HD-CVI • HD-TVI
Note:
This manual may contain some incorrect places, even though it was published
with our carefully proofreading. The news updates will be added to the next
release without notice. Your valuable advice is really appreciated.
Thank you for purchasing our product. If there are any questions, please read
this user manual at first, and do not hesitate to contact us.
| Model | 1080P 4-in-1 HD Camera |
|---|
Camera
Image Sensor| 112.r 2.1 Mega pixels CMOS
Chipset| AR0230+FH8538
Effective Pixels| 1928(H)0088 (V)
Lowest illumination| 0.02Lux© (F1.2AGC ON I .0 Lux with IR
Electronic Shutter| 1506-1/60.000s
Video System| PAY/NTSC
Video Frame Rate| 25f30ps@1920.1080P
Video Output| 1 channel. HOCVI / HDTWAHD/CVBS optional
Video Switch| 2-bit switch
Smart IR Ca-itrd| SWIM
Day/Night| Auto(ICR) / Color / BM
WDR| D-WOR
OSD Menu| Support. coaxial cable control via DVR directly (UTC)
Other Function| AWL AGC. BLC
General
Power Supply| DC12V±10%
Power Consumption| < 5W
Working Environment| -30°C-050t / Less than 95%RH
IR LED| 24(30(38/4892 pa selectable
IR Distance| 10/15/20/30/5080 meters selectable
Lens| 3.8/6/E112118/25 mm selectable
Transmission Distance| Over 300m via 75-3 coaxial cable
Cautions:
Make sure the power supply is matched with the camera power input to avoid damage. Neither the power adapter nor video cable should be beyond the longest transportation limit.
1.Image black/white, rollover
- check the camera rear mode switch cable, adjust it and make sure the video output is matched for your DVR.
- go to the camera menu and change the PAL/NTSC mode.
2.Video signal shows horizontal ribbon disturbed area
- check the power supply cable, it should not be too long, or change a high-quality power adapter to replace it.
- Make sure the DVR BNC port is connected stable and the DVR housing GND is grounded.
3.Camera keep white/black, IR led not working or keep on, glass cover broken, etc.
- Call the franchiser to repair. Please do not open or try repairing it without permission.
OSD Menu Control
This series HD camera can support OSD menu coaxial control by reusing the
video cable. It means the user can configure, without a menu button, the
camera parameters via DVR directly. ( the DVR also should support UTC ) It’s
immensely convenient for site adjustment.
How to enter the camera menu? In general, the DVR must have the coaxial
control feature. Go to the PTZ control window and click the “+ iris -” to call
out the camera menu.
The menu contents are listed as below:
AE: auto image enhancement
WB: white and black balance mode
DAY-NIGHT: day and night switch mode
VIDEO SETTING: video basic parameters, PAL/NTSC, WDR, DNR adjustment
LANGUAGE: menu language select
RESET: reload factory default
SAVE-EXIT: save all settings and exit menu.
ATW: auto-tracking white balance — default mode
Color: keep color
WB: keep white and black mode
Smart: auto change to color and WB
DNR: digital noise reduce — reduce the image noise points in a dark
environment
WDR: Wide dynamic range — pick up a balanced image when working in a back-
light environment
Functions brief
- HD CMOS sensor Within high sensitivity CMOS image sensor, 1080P video output, very low illumination Perfect image quality emerge both on day and night environment
- 4-in-1 Multiple Video modes output Support 4 HD signals switch output, AHD/HDCVI/HDTVI/ CVBS, easy to use switch cable
- OSD menu controls up the coaxial cable(UTC) Camera parameters can be set up via the built-in menu. All the configurations can be changed by back-end DVR directly up the coax. No need to press the cable button
- Over 300 meters of long-distance video signal transportation
- Smart IR control, AGC, D-WDR, DNR
- Wide range voltage adaptation, Lightning protection
- Strong and pretty housing, installations angles can be adjusted
Caution :
Please install this device at inappropriate temperature, -30 ℃- 60 ℃ or -22 ℉
– 140 ℉, keep away from corrosive gas and liquid.
Don’t put the camera directly into the sunlight, it is recommended to install
it under a sunshade.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>