MONACOR TVCCD-385 HCOL Colour Camera User Manual

: June 3, 2024
: MONACOR

Table of Contents

MONACOR TVCCD-385 HCOL Colour Camera
Applications
Important Notes
Installation
Specifications
ABOUT COMPANY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MONACOR TVCCD-385 HCOL Colour Camera

Please read these operating instructions carefully prior to installing and keep them for later reference.

Applications

This colour camera with 24 white light LEDs is especially designed for application in video surveil-lance systems (CCTV). Due to its robust spherical metal housing it is weather-proof (IP 66) and protected against vandalism and can therefore also be used outdoors.
When darkness falls and in case of movement, the integrated PIR motion sensor switches on the LEDs (6) for approx. 25 seconds.
The camera is equipped with a 3.6 mm lens, an automatic gain control (AGC) and digital noise reduction (DNR). The switching outputs allow to control video recorders, alarm facilities and additional illumination. Via an input the LED illumination can additionally be switched on.

Important Notes

The camera corresponds to all relevant directives of the EU and is therefore marked with
CAUTION! Never look directly into the lit LEDs at close range, it may cause eye damage.

Protect the camera against extreme temperatures (admissible ambient temperature range – 10 °C to +50 °C).
For cleaning do not use aggressive detergents or chemicals.
No guarantee claims for the camera and no liability for any resulting personal damage or mate-rial damage will be accepted if the camera is used for other purposes than originally intended, if it is not correctly installed or not repaired in an expert way.
If the camera is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.

Installation

The connections (8 – 10) and the cable distributor (7) are not weatherproof. In case of outdoor installation they have to be protected accordingly.

To determine the perfect place of mounting, a test run should be made. Then drill at the place of mounting four holes for fixing the base (3) and, if required, a hole for the connection cable (the cable can also be led through one of the four cable inlets at the side of the base). Fasten the base with the mounting material provided.
Place the camera (4) with the inner supporting ring (1) and the outer supporting ring (2) onto the base (3). To be able to align the camera to the surveillance zone after setting it into operation, for the time being only fasten the outer supporting ring onto the base so that the camera can still be moved.
Connect the yellow BNC plug (9) to the video input of a monitor. With a cable length of more than 100 m a video amplifier should be inserted between the camera and the cable to compensate level loss.
The terminal block (10) offers the following connection possibilities:
- If the PIR sensor detects a movement, the trigger output (terminal 1) is switched to ground (terminal 5). Via a corresponding alarm input of a video recorder e. g. a video recording can be started.
- To switch on the LEDs e. g. via an external motion sensor, connect terminal 3 (+5 V) via a closing contact (NO) to the sensor input of terminal 2. The LEDs are only lit in case of darkness.
- At the output “Alarm” (terminal 4) and the ground contact (terminal 5) an additional illumination or an alarm facility can be switched together with the LEDs e. g. via a relay (with protective circuit at the coil). The output supplies +12 V at 0.5 A max.
Connect a regulated 12 V power supply unit with a permanent rating of 250 mA as a minimum plus the required switching current for the alarm output (10) to the red inline jack (8). A low volt-age plug 5.5 / 2.1 mm (outside / inside diameter) is required. Always observe the correct polarity (centre contact = +).
Switch on the connected monitor and align the camera by means of the monitor image: Turn the camera in the inner supporting ring and the inner ring in the outer ring as desired.
After the alignment fasten the outer supporting ring on the base and secure it with the hexagon socket screw (5).