NITECORE BP-SCL4 Benchmarkin Intelligent Charger User Manual
- June 5, 2024
- Nitecore
Table of Contents
**NITECORE BP-SCL4 Benchmarkin Intelligent Charger User Manual
**
Product Overview
Features
- Compatible with Leica’s BP-SCL4
- USB input
- Real-time information on battery voltage, charging current, battery temperature, battery level and other parameters
- Monitors battery status and displays battery health
- Reverse polarity protection and anti-short circuit protection
- Automatic adoption of optimal charging mode: CC or CV
- Automatic termination upon charging completion
- Activates over-discharged batteries with protective circuits
- Compatible with power banks and 5V solar panels
- Made from durable and fire retardant PC and ABS (V0) materials
- Optimal heat dissipation design
Specifications
Input: DC 5V/2A
Output voltage: 8.4V±1%
Output current: 1000mA (MAX)
Interface: Input: USB Output: Connector
Battery compatibility: Leica’s BP-SCL4
Compatible models: SL Typ601, Q2, SL2, Q2 Monochrom, SL2-S Dimensions:
3.34”×1.96”×1.16” (85mm×50mm×29.5mm) Weight: 1.96oz (55.8g)
Operating Instructions
The ULSL is designed specifically for Leica’s BP-SCL4 camera battery; it is not designed to work with other batteries. The output current is adjusted automatically according to input current to reach optimal charging setting. This product shall NOT be used with other batteries not specified in this manual.
Automatic Current Adjustment
The ULSL’s actual output current depends on the maximum power supplied from the USB. Output current will adjust based on actual power being input to the device. The ULSL is capable of outputting 1000mA and increasing its efficiency while shortening charging duration.
Battery Health Monitoring
Once the battery is inserted, the ULSL will perform an initial low current
test charge to diagnose battery status. After completing the diagnosis, the
battery status will be shown as Good, Normal or Poor.
Note: Re-insert the battery when “Poor” appears on screen to avoid the
possibility of a poor battery contact. Replace the battery if “Poor” comes up
on the screen consistently.
Reverse polarity and Anti-Short Circuit protection
The ULSL uses mechanical reverse polarity protection. Inserting incompatible
batteries or incorrectly installing batteries will prevent the initiation of
the charging process. The error message “EE EE” will come up on the LCD
display when a short circuited battery is installed.
Note: When the display shows the error message “EE EE”, please put the
battery into the original battery charger for 30 minutes to activate it. If it
is still unable to get charged after this, please replace the battery.
Battery recovery
The ULSL will attempt to recover over-discharged batteries when inserted into
the charging slot. Upon successful battery recovery, the entire battery level
indicator will flash to represent that a battery has been successfully
recovered.
Note: This feature only works with protected batteries.
Precautions
- The ULSL is only compatible with Leica’s BP-SCL4 camera Do NOT attempt to charge other batteries.
- Moderate heat from this product is to be expected during the charging This is normal.
- Operating temperature: -10° to 40°C, storage temperature: -20° to 60°
- Carefully read all labels on the device to ensure batteries are installed
- The charger is designed for adults. Use of the charger by kids under age must be under supervision. Operation, using or cleaning of the charger may NOT be done by kids aged 8 years or younger.
- DO NOT leave the product unattended while it is connected to a power Unplug the product at any sign of malfunction and refer to the user manual.
- Batteries should be replaced as soon as possible when near the end of the expected charging cycle
- DO NOT store or use the product in an environment where the temperature is extremely high / low or changes rapidly, or in a confined area with a high temperature.
- Store the device in ventilated DO NOT uses the device in moist environment and keep away from any combustible materials.
- Avoid any shock or impact to the
- DO NOT place any conductive or metal object in the device to avoid short- circuiting and explosions.
- Unplug the device when it is not in
- DO NOT disassemble or modify the device as doing so will render the product warranty invalid. Please refer to the warranty section in the manual for complete warranty information.
Warranty details
Our authorized dealers and distributors are responsible for warranty service. Should any problem covered under warranty occurs, customers can contact their dealers or distributors in regards to their warranty claims, as long as the product was purchased from an authorized dealer or distributor. NITECORE’s Warranty is provided only for products purchased from an authorized source. This applies to all NITECORE products. Any DOA / defective product can be exchanged for a replacement through a local distributor/dealer within the 15 days of purchase. After 15 days, all defective / malfunctioning NITECORE® products can be repaired free of charge for a period of 12 months (1 year) from the date of purchase. Beyond 12 months (1 year), a limited warranty applies, covering the cost of labor and maintenance, but not the cost of accessories or replacement parts.
The warranty is nullified if the product(s) is/are
- broken down, reconstructed and/or modified by unauthorized parties
- damaged from wrong operations (i.e. reverse polarity installation, installation of non-rechargeable batteries), or violation of the warnings
- damaged by batteries leakage.
For the latest information on NITECORE® products and services, please contact a local NITECORE® distributor or send an email to service@nitecore.com
※ All images, text and statements specified herein this user manual are for reference purpose only. Should any discrepancy occur between this manual and information specified on www.nitecore.com, the information on our official website shall prevail. SYSMAX Innovations Co., Ltd. reserves the rights to interpret and amend the content of this document at any time without prior notice.
Validation code and QR code on package can be verified on Nitecore website.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: info@nitecore.com
Web: www.nitecore.com
Address： Rm 2601-06, Central Tower,
No.5 Xiancun Road, Tianhe District, Guangzhou,510623, Guangdong, China
Manufacturer: SYSMAX Power Technology, LLC
Made in china
Thanks for purchasing NITECORE!
Please find us on facebook : NITECORE photo
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>