hama 00179806 SONY TVs Replacement Remote Control Instruction Manual

hama 00179806 SONY TVs Replacement Remote Control

Operating instruction

Thank you for your decision for a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future eference.
This remote control can by default control 90% of models of the SONY brand, there´s no need to set it up. lf the remote doesn‘t work, please choose one of the setup methods described in chapter 5.

The keys

1. PictureSize
2. Power TV ON /OFF
3. Display Text Reveal /Indicator LED
4. Goes backward(DVD, BlueRay … )
5. Play adisc (DVD, BlueRay … )
6. Fast Forward(DVD, BlueRay … )
7. Suspends play and stops on an image (DVD, BlueRay…)
8. SYNC MENU
9. Stop the disc (DVD, BlueRay … )
10. THEATER
11. Exit Menu
12. OFF TIMER
13. Audio Setting
14. Subtitle
15. Show the Electronic Program Guide (if supported by the TV)
16. Switch TV or AV mode
17. Media Player
18. Return /Back key
19. Streaming app menu
20. Turn your TV sound ON/OFF
21. Programmer Menu
22. Switch Digital/Analog
23. Use to select avariety of on screen options
24. Volume +/-
25. Program +/-
26. Numeric keys 0–9to enter channel numbers
27. Access to 2- or 3-digit channel numbers
28. Previous Channel
29. Teletext ON/OFF
30. TV
31. Player Previous (DVD, BlueRay…)
32. 3D Mode ON/OFF
33. Discover
34. Player Next (DVD, BlueRay…)

Package Contents

• Replacement Remote Control
• 2x AAA Batteries
• This operating instructions incl. Code List
• Do not use the remote control in moist or wet environments and avoid spray-water contact.
• Do not expose the remote control to heat sources or direct sunlight.
• Do not drop the remote control.
• Never open the remote control. It contains no user-serviceable parts.
• As with all electrical devices, keep the remote control away from children.

Warning

•  When inserting batteries, note the correct polarity (+ and -markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
•  Do not short-circuit batteries.
•  Do not charge batteries.
•  Do not throw batteries in a fire.
•  Keep batteries out of the reach of children.
•  Do not allow children to change batteries without supervision.
•  Remove the batteries from products that are not being used for an extended period.

Getting started – installing the Batteries

•  Use 2AAA batteries
•  Remove the battery cover from the bottom of the remote.
•  Check the +/- polarity on the batteries and inside the compartment.
•  Insert the batteries.
•  Slide the battery holder back into the remote until the clips locate.

This remote control saves the settings during battery change.

Setup

This remote control can by default control 90% models of SONY brand, there´s no need to set it up. lf it doesn‘t work, please choose one of the following setup methods 5.1 or 5.2.

INPUT CODE

CODE List: 001, 002, 003, 004, 005, 006, 007, 008, 009, 010, 011, 012, 013, 014, 015, 016, 017, 018, 019, 020, 021, 022, 023, 024, 025

1. Press and hold the key [MUTE] and [POWER] until the LED will be lit, then release keys.
2. Enter the three codes from code Iist. When the code input is finished, the LED will turn off.
3. Please try to use the remote control. lf it doesn‘t work well, please try other codes: [002], [003], [004] …

If the code is invalid, the LED flashes twice and then lights up permanently. To exit the setup, please press [MUTE].

FAST SEARCH

1. Press and hold the key [MUTE] and [POWER] until the LED will be lit, then release keys.
2. Press the key [PROG+]. Each time you press, the remote will search once. When the code changes, you can test if [POWER], [VOL+],[MENU],[0-9] keys work well. If ok ,please press [MUTE] to save the code and exit.
3. If it doesn‘t work well, repeat the fast search by pressing [PROG+].

CODE INQUIRY

Use the following method to find out which code is currently set:

1. Press and hold [MUTE], then press [POWER] until the LED will be lit, then release keys.
2. Input [9].[9].[0] with number keys. The LED will flash twice and goes off.
3. Press the number key 1for the 1st digit of the code. The LED will start to flash. Count the LED flashes. The number of flashes resemble the code‘s first digit. Repeat this procedurefor the 2nd and 3rddigit of the code:
   2nd digit -> enter 2->count LED flashes
   3rd digit -> enter 3->count LED flashes
   lf code number is [0] the LED will not flash.

Compatible Remote Control Model
Due to too many remote control models, we only Iist some of them below. lf your remote control is similar to the drawing, the replacement remote can control your TV (Page 47).

Resetting to factory settings
Press and hold the [RETURN] and [0] buttons for about 5seconds until the status LED flashes three times and then goes out. The remote control is now successfully reset to the factory settings.

LEARN MODE

This remote control is equipped with alearning function. Thus, you could learn functions of your original remote to this remote control.

BEFORE STARTING LEARN MODE

•  The batteries in the two remote controls have to be in good condition. Replace them if necessary.
•  Place the remote controls with the infrared diodes so that they point towards each other.
•  Where necessary adjust the height of both remotes so that infrared diodes are properly aligned.
•  The distance between the remote controls should be about 3cm.

Note

• Do not move the remote controls during the learning procedure.
• Ensure that the room is not lit by fluorescent tubes or low energy consumption lamps since such light sources could interfere with the copying.
• The 2remotecontrols must be at least 1meter away from any light source.
• During learning mode, if no key is selected for more than 15 seconds, the learning mode will exit automatically or
• if no other remote signal is received.
• Each function key will hold only one command. A new command to be learned will automatically replace the previous one.

ENTER LEARN MODE

1. Press and hold the [MUTE] and [VOL+] keys for approx. 5seconds until the LED will be lit.
2. Enter the code [9] [8] [0], the LED will flash 2times and then remain on.
3. The remote control is now ready to learn new commands.

LEARNING OF KEYS

1. Press and release the desired key on the original remote control which you want the command to be learned. The LED at your replacement remote will flash to confirm that the information has been received.
2. Then press and release the target key on the remote control you want to be learned.
3. If the LED flashes 3times and then remains on, the command has been learned successfully.
4. Repeat these steps to learn other key functions.
5. Press the [MUTE] and [VOL-] buttons to save all learnt functions and to exit the learning mode.

CLEARING OF LEARNED KEYS

CLEARING OF ONE LEARNED KEY

1. Press and hold [MUTE] and [VOL+] keys for 5seconds until the LED will be lit.
2. Enter the code [9] [8] [1], the LED will flash 2times and then remain on.
3. Press and release the desired key at the replacement remote control which you want to clear the learned command. If the LED flashes 3 times, the learned command has been cleared successfully.

CLEARING OF ALL LEARNED KEYS

1. Press and hold [MUTE] and [VOL+] keys for 5seconds until the LED will be lit.
2. Enter the code [9] [8] [2], the LED will flash 2times and then remain on.
3. Press and release the [OK] key at the replacement remote control. If the LED flashes 3times, all commands have been cleared successfully.

EASY Mode

This remote control is equipped with an EASY Mode. Thus you could reduce the functionality of the remote control to its basic functions. It avoids that the TV Settings are changed by mistake.
During the EASY Mode you still could use the following keys:

Enter EASY Mode

1. Press and hold [MUTE] and [VOL+] keys for 5seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3. Press and release the [OK] key, if LED flash 3times, you have entered the EASY Mode successfully.

Exit EASY Mode

1. Press and hold [MUTE] and [VOL+] for 5seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3. Press and release the [EXIT] key, if LED flash 3times, you have exit the EASY Mode.

While the EASY Mode is activated only the keys mentioned in chapter 7. will work. If one of these keys is pressed the LED will be lit until the key is released. If one key is pressed during the normal mode, the LED will flash.

Maintenance

•  Do not mix new and used batteries for powering the remote control, as old batteries tend to leak and may cause power drain.
•  Do not use corrosive or abrasive cleansers on your remote control.
•  Keep the remote control dust free by wiping it with asoft, dry cloth.

Troubleshooting

Q. My Universal remote control does not work at all!

• Check your TV. If the TV main switch is turned off, your Remote cannot operate your TV.
• Check whether your batteries are inserted properly and are in the correct +/- position.
• If the batteries are low, replace the batteries.

Q. My TV responds only to some of the commands.
A. Try other codes until most keys work properly.

Q. Some keys of the remote control do not work anymore?
A. Maybe the EASY Mode had been activated. Deactivate the EASY Mode as explained in chapter 7.2.

Warranty Disclaimer
The manufacturer assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failuretoobserve the operating instructions and/or safety notes.

Service and Support
Please contact Hama Product Consulting if you have any questions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here: www.hama.com

Recycling Information

Note on environmental protection:
After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices, as well as batteries, must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices/Batteries, you are making an important contribution to protecting our environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>