OSRAM Luxvance Street Light Pro Instruction Manual
- July 6, 2024
- OSRAM
Table of Contents
OSRAM Luxvance Street Light Pro
Specifications
Model| Width (mm)| Length (mm)| Height (mm)| Wattage (W)| Installation Height
(m)| Weight (kg)| Voltage (v)
---|---|---|---|---|---|---|---
LUXVANCE ST PRO 60W| 200| 562| 108| 60W| 6-9| 3.12| 240V 50Hz
LUXVANCE ST PRO 90W| 240| 607| 108| 90W| 8-11| 4.28| 240V 60Hz
LUXVANCE ST PRO 120W| N/A| N/A| N/A| 120W| N/A| N/A| N/A
LUXVANCE ST PRO 150W| 260| 680| 108| 150W| N/A| N/A| N/A
LUXVANCE ST PRO 180W| N/A| N/A| N/A| 180W| N/A| N/A| N/A
LUXVANCE ST PRO 200W| 300| 766| 108| 200W| N/A| N/A| N/A
LUXVANCE ST PRO 240W| N/A| N/A| N/A| 240W| N/A| N/A| N/A
DIMENSION
USING INSTRUCTION
- Loosen the shaft support until the shaft is free to rotate.
- Adjust the angle of the lamp head and secure it by tightening the screws.
- Initially, ensure that the power switch is in the OFF position, followed by connecting the input line to the lamp.
- Secure the lamp by tightening the pole screws to prevent it from becoming unstable.
- Gently cleanse the outer surface of the glass
- Flip the switch to the ON position, power up the lamp, and check if the lamp illuminates
- NEMA assembly
WARNING
- Ensure that any installation and maintenance are performed by a qualified electrician and the luminaire is wired by the local wiring and relevant Australian standards.
- Ensure that the power supply is off before starting installation and maintenance. Do not switch on until the installation or maintenance is completed.
- The light source of this luminaire is a non-user alternative light source, the light source contained in the luminaire shall only be replaced by the manufacturer of his service agent or a similar qualified person.
- Make sure the products are grounded.
- The power supply system should be equipped with SPD (Surge Protection Device) in accordance with electrical regulations.
- The products are suitable for outdoor use.
- For luminaires with dimmable LED drivers
- For NEMA version, make sure to meet the waterproof requirement after installing the short cap or NEMA controller.
- The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 3m is not expected.
- The glass cover was constituted with glass having a high impact shock resistance.
Service Contact
Haneco Lighting Australia Pty Ltd
262 Marion Road, Netley, South Australia 5037
Haneco.com.au
OSRAM is a trademark of OSRAM GmbH.
Traxon e: cue is a licensee of OSRAM brand for a fixed list of General
Lighting products. Haneco Lighting Australia is the exclusive distributor in
Australia, New Zealand, and the Pacific Islands.
MANUFACTURER
- Shenzhen Eastfield Lighting Co., Ltd.
- No.10 Huanping Road,
- Gaoqiao District, Pingdi Street, Longgang Area, Shenzhen, Guang-dong, China
- Phone: +86 755 29512685
OSRAM OFFICIAL LICENSEE
Traxon Technology Ltd. 213 Wireless Centre, 3 Science Park East Avenue,
Science Park, Shatin, New Territories, Hong Kong
Phone: +852 2943 3488
www.traxon-ecue.com
Frequently Asked Questions
- Q: Can I replace the light source myself?
- A: The light source should only be replaced by the manufacturer, their service agent, or a qualified person.
- Q: Is the product suitable for outdoor use?
- A: Yes, the product is suitable for outdoor use. Ensure it is grounded and meets relevant electrical regulations.
- Q: What should I do before installation and maintenance?
- A: Ensure any installation and maintenance are performed by a qualified electrician and the power supply is switched off
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>