MONACOR DMP-130MIXBT Mikrofon Line Mischer Microphone Line Mixer Instruction Manual

May 15, 2024
MONACOR

MONACOR DMP-130MIXBT Mikrofon Line Mischer Microphone Line Mixer

MONACOR-DMP-130MIXBT-Mikrofon-Line-Mischer-Microphone-Line-Mixer-
product

Specifications

  • Model : DMP-130MIXBT
  • Power Input : 230V~ 50Hz
  • Inputs: Mono microphone (XLR or 6.3mm plug), Stereo input (3.5mm jack), Stereo input (RCA jacks)
  • Outputs : Two stereo outputs (UNBAL: RCA jacks, BAL: XLR connectors)

Product Usage Instructions

Front Panel:

The front panel features controls for POWER, AUX, MIC, MODE, EQ, and volume adjustments for MIC, AUX/MP3, LINE, TREBLE, and BASS.

Rear Panel:

The rear panel includes inputs for CD/LINE and outputs for UNBAL. L/R and BAL. L/R. It also features the power input and fuse.

Using the Audio Player:

  1. Connect a microphone to the mono input or an audio source to the stereo inputs.
  2. Use the display to navigate through the audio player functions. C = memory card, U = USB medium.
  3. For Bluetooth mode, check the display for connection status: Disconnected = no connection, Connected = connection established.

Remote Control

Use the remote control to operate the audio player functions as per the table provided in the manual.

Volume Control

Adjust volume levels for MIC, AUX, and CD/LINE inputs individually and use the total volume control for overall output.

TREBLE and BASS Controls

Modify the treble and bass settings to suit your audio preferences.

FAQ

  • Q: How do I connect a microphone to the mixer?
    • A : Connect your microphone using an XLR or 6.3mm plug to the mono input on the front panel.
  • Q: Can I use a USB flash drive with this device?
    • A : Yes, you can connect a USB flash drive to the USB port on the audio player for playback.
  • Q: What do the symbols on the display indicate during playback?
    • A : The symbols indicate replay, pause, or stop functions during playback on the audio player.

Front panel with remote control

MONACOR-DMP-130MIXBT-Mikrofon-Line-Mischer-Microphone-Line-Mixer-
fig1

MONACOR-DMP-130MIXBT-Mikrofon-Line-Mischer-Microphone-Line-Mixer-
fig2

Rear panel

MONACOR-DMP-130MIXBT-Mikrofon-Line-Mischer-Microphone-Line-Mixer-
fig3

Overview

MONACOR-DMP-130MIXBT-Mikrofon-Line-Mischer-Microphone-Line-Mixer-
fig4

Microphone/Line Mixer with Audio Player

These instructions are intended for users without any specific technical knowledge. Please read the instructions carefully prior to operation and keep them for later reference. All operating elements and connections described can be found in the figures on page 2.

Applications

This audio mixer with three input channels is suited for universal applications, for example in bars or function rooms. It offers connections for a microphone and two stereo audio sources with line signal level (e. g. mixer, CD player). It also features an integrated audio player with USB port, a slot for memory cards and a Bluetooth receiver. The mixed signal is available at two outputs.

The mixer is designed for installation into a rack for devices with a width of 482mm (19“). In the rack, one rack unit (1U = 44.45mm) is required.

Safety Notes

The product corresponds to all relevant directives of the EU and is therefore marked with . The product corresponds to the relevant UK legislation and is therefore marked with UKCA

WARNING The product uses dangerous mains voltage. Leave servicing to skilled personnel only. Inexpert handling may result in electric shock.

  • The product is suitable for indoor use only. Protect it against dripping water, splash water and high air humidity. The admissible ambient temperature range is 0–40°C.
  • Do not place any vessel filled with liquid on the product, e. g. a drinking glass.
  • Do not use this product and immediately disconnect the mains plug from the socket
    • 1. if the device or the mains cable is visibly damaged,
    • 2. if a defect might have occurred after the device was dropped or suffered a similar accident,
    • 3. if malfunctions occur. Any repairs must be carried out by specialists.
  • Never pull the mains cable to disconnect the main plug from the socket, always seize the plug.
  • For cleaning the product only use a dry, soft cloth; never use water or chemicals. No guarantee claims for the product and no liability for any resulting personal damage or material damage will be accepted if the product is not correctly used or not expertly repaired.

If the product is to be put out of operation definitively, dispose of the product in accordance with local regulations.

Connection

Before connecting /disconnecting, switch off all devices concerned.

1) To connect a microphone, use the jack
MIC (2): Connect the microphone via a 6.3mm plug or XLR plug.
2) Two inputs are provided to connect stereo audio sources with line signal level (e. g. MP3 player, CD player, FM/DAB tuner, tape deck, PC, mixer):

  • * the 3.5mm jack AUX (3); when this jack is used, the integrated audio player will be muted.
  • the RCA jacks INPUT CD/ LINE (14);
  • L (white) = left, R (red) = right
    • 3 ) To route the mixed signal to subsequent devices (e. g. to an amplifier), two outputs
  • (15) are provided which can be used at the same time:
    • the RCA jacks OUTPUT UNBAL.
    • the XLR connectors OUTPUT BAL.
    • The XLR outputs should be preferred; the balanced signal transmission of XLR connections is less susceptible to interference.
  • 4) For the power supply, connect the mains cable provided to the mains jack (16) first and then to a mains socket.

Operation

  1. Before switching on the mixer for the first time, set the total volume control VOLUME (12) to “MIN”.
  2. Use the POWER switch (1) to switch on the mixer.
  3. Turn up the control VOLUME to adjust the total volume desired; for each audio source to be heard, adjust the volume by means of the corresponding control:
    • control MIC (9) for the microphone connected to the input MIC (2)
    • control AUX/MP3 (10) for the device connected to the input AUX (3) or, when the input AUX is not used, for the integrated audio player (the basic volume for the audio player is adjusted separately: ☞ fig. 4)
    • control LINE (11) for the device connected to the input CD/ LINE (14)When an input/an audio source is not used, set its control to “MIN”.
  4. Use the controls TREBLE and BASS (13) to adjust the tone for the mixed signal.

Audio Player

When the mixer is switched on, the audio player will be automatically activated, and the operating mode last used (“USB storage medium”, “Memory card” or “Bluetooth”) will be selected.

Infrared remote control

The remote control provided uses a battery (3V button cell, type CR2025). If a battery has been inserted in the factory, remove the protective film (to protect the battery from being discharged) from the battery support. The remote control is now ready for use. When you press a button on the remote control, always point the remote control at the infrared sensor (4). Make sure that there are no obstacles between the remote control and the sensor. If the remote control is not used for a longer period of time, remove the battery as a precaution so that the remote control will not be damaged in case the battery should leak.

Inserting/Replacing the battery:

  1. Push the latch of the battery support to the right (arrow 1 in Fig. 3) and then pull out the support (arrow 2).
  2. To replace the battery, remove the discharged battery.
  3. Insert the new battery in the support, positive pole facing upwards. Push the support back into the remote control.

Never put batteries in the household waste. Always dispose of the batteries in accordance with local regulations.

Operating mode “USB storage

medium“ or “Memory card” The player can be used to reproduce MP3 files from memory cards (SD/ SDHC / SDXC) and USB storage media (USB hard disk withseparate power supply or USB flash drive). It also supports reproduction of WMA files, WAV files and FLAC files.

Connecting storage media:

  • * Connect a USB storage medium to the USB port (6).
    • Insert a memory card, notched corner facing to the right and towards the device, into the card slot (7).
  • Note: Due to the large number of storage device manufacturers and device drivers, it cannot be guaranteed that all storage media are compatible with the audio player.

If the operating mode “USB storage medium” or “Memory card” is activated after switching on and the corresponding storage medium has already been connected, reproduction of the medium will start automatically after it has been read in. If, however, the corresponding medium is missing, NO SOURCE will appear on the display (5).

As soon as a medium is connected, this medium is selected for reproduction: If, for example, a USB flash drive is connected in the mode “Memory card”, the audio player will automatically switch to the mode “USB storage medium”. If two media have been connected, use the button MODE to switch over between the media.
The control options can be found in the table (fig. 4). Information on the display indications can be found in the overview on page 3.

Operating mode “Bluetooth”

In “Bluetooth” mode, audio data can be transmitted wirelessly from an audio source using Bluetooth transmission (e. g. smartphone) to the audio player.

Establishing a Bluetooth connection:

  1. Use the button MODE to select the operating mode “Bluetooth” ( Bluetooth shown on the display):MONACOR-DMP-130MIXBT-Mikrofon-Line-Mischer-Microphone-Line-Mixer-fig8

Functions of the buttons

  1. * The display will show Disconnected! as long as there is no Bluetooth connection.
  2. At the Bluetooth source, activate the Bluetooth function. On the list of available devices, the Bluetooth receiver of the audio player will appear under the name “DMP-130MIXBT”. Pair the Bluetooth source with “DMP-130MIXBT” (consult the instructions for the Bluetooth source if necessary). Once the Bluetooth connection has been established, the display will show Connected!.

  3. Start the audio reproduction on the Bluetooth source and operate the Bluetooth source as desired.
    For operation, the following buttons of
    the audio player can also be used:

    • button II: replay /pause
    • button I: skip to the next track
    • button I : return to the beginning of the track, then back one track at a time with each press of the button

Specifications

  • Frequency response : ..,,,… 20– 20 000Hz
  • THD: ,,,……. < 0.1%
  • Channel separation: ….. > 60 dB
  • Dynamic range : …….. > 96 dB
  • S/N ratio : ………..> 70 dB
  • Inputs (sensitivity/ impedance; connection)
  • MIC, mono : …….. 2.5mV/550Ω;
  • XLR and 6.3mm jack, bal.
  • AUX, stereo:,…… 350mV/30 kΩ; 3.5mm jack
  • CD/ LINE, stereo:…………. 600mV/30 kΩ; RCA
  • Rated output level
  • XLR, bal.: ………1.8V
  • RCA: ……….. 890mV
  • Power supply: ………~230V/ 50Hz
  • Power consumption:…… 20VA max.
  • Ambient temperature: ……. 0 –40 °C
  • Dimensions (W×H×D): 482×44×160mm
  • Rack units : …………. 1U
  • Weight:……… 2.5 kg

Bluetooth specifications

  • Frequency band: ……. 2.4GHz
  • Transmission
    • power (max.): ……….. 4 dBm
    • Version :……………..5.3
    • Range : ……………….. up to 20m (depending on local conditions)

Conformity and approval

Hereby, Monacor International GmbH & Co KG declares that the radio equipment type DMP-130MIXBT is in compliance with Directive 2014 /53/ EU. The full text of the EU Declaration of Conformity is available at the following Internet address:
www.monacor-international.com

Subject to technical modification.

All rights reserved by MONACOR ® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be reproduced in any form or by any means for any commercial use

© MONACOR INTERNATIONAL

All rights reserved
A-2061.99.02.07.2023

MONACOR INTERNATIONAL GmbH & Co. KG Zum Falsch 36, 28307 Bremen Germany

Importer: Epic Audio Ltd, Unit 9 Apollo Park Station Road, Long Buckby, NN6 7PF
United Kingdom, Company Registration: 13878247

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals