MONACOR WALL-05T PA Wall Speakers User Manual
- June 4, 2024
- MONACOR
Table of Contents
MONACOR WALL-05T PA Wall Speakers
These instructions are intended for in-stallers with specific knowledge in sound reproduction using 100 V technology. Please read the instructions carefully prior to installation and keep them for later ref-erence.
Applications
These speaker pairs are specially designed for PA systems. Featuring a 2-way
system, the speakers offer excellent sound quality and speech intelligibility.
The speakers are provided with a transformer for operation in 100 V sys-tems,
but they can also be directly connected to a low-impedance amplifier output. A
rotary switch is used to match the connected load.
By means of their mounting bracket, the speakers can be fastened to a wall or
ceiling. Due to their weatherproof housing (IP 65), the speakers are also
suited for outdoor applica-tions.
Important Notes
The speakers correspond to all relevant direc- tives of the EU and are
therefore marked with .
- Protect the speakers against extreme tem-peratures (admissible temperature range: 0 – 40 °C).
- Never use aggressive detergents or chemicals for cleaning.
- No guarantee claims for the speakers and no liability for any resulting personal damage or material damage will be accepted if the speakers are used for other purposes than originally intended, if they are not correctly installed, if they are overloaded or if they are not repaired in an expert way.
NOTE: If the speakers are to be put out of operation definitively, take them to a local recycling plant for a disposal which is not harmful to the environ-ment.
Installation
WARNING During operation, there is a hazard of contact with a voltage of up to 100 V at the speaker cable. Installation must be made by skilled personnel only. Observe the load of the PA amplifier by the speakers. An overload may damage the am-plifier!
-
Before installing the speaker, switch off the PA amplifier so that the speaker cable will not carry any voltage!
-
Remove the plastic support (4) from the metal bracket (3).Then use two screws to fasten the support to the desired location (e. g. wall or ceiling).
-
Fasten the metal bracket (3) to the plastic support, using the two recessed head screws of the bracket. Use the holes in the metal bracket which are most suitable for the de-sired speaker alignment.
-
Use the screws (2) to fasten the speaker (1) to the metal bracket. Before tightening the screws, connect the speaker and align it to the desired sound zone.
-
Remove the connection cover.
-
Adjust the power rating for 100 V operation on the rotary switch. For direct operation at a low-impedance amplifier output, set the switch to the position “8 Ω”.
CAUTION! Never use the position “8 Ω” when the speaker is operated in a 100 V system: The speaker and possibly also the amplifier will be damaged. -
Connect the cable to the terminals. Make sure that all speakers have the same polarity (e. g. ⊕ = red terminal).
-
Replace the connection cover.
Specifications| WALL- 04T/…| WALL- 05T/…| WALL-
06T/…| WALL- 08T/…
---|---|---|---|---
Power rating
100 V operation
8 Ω operation
|
16 / 8 /4 /2 W
30 W
|
16 / 8 /4 /2 W
40 W
|
32 / 16 / 8 /4 W
50 W
|
50 / 25 / 12.5 / 6.25 W
60 W
Music power| 60 W| 80 W| 100 W| 120 W
Frequency range| 90 – 20 000 Hz| 80 – 20 000 Hz| 70 – 20 000 Hz| 35 – 20 000
Hz
SPL| 87 dB (1 W/1 m)| 89 dB (1 W/1 m)| 90 dB (1 W/1 m)| 90 dB (1 W/1 m)
Max. SPL| 100 dB| 104 dB| 106 dB| 106 dB
Speaker configuration Bass-midrange speaker Dome tweeter|
10 cm (4”)
12 mm (½”)
|
13 cm (5”)
12 mm (½”)
|
16 cm (6”)
25 mm (1”)
|
20 cm (8”)
25 mm (1”)
Connection| terminals
Dimensions (with bracket) Width
Height
Depth
|
130 mm
197 mm
164 mm
|
163 mm
252 mm
203 mm
|
196 mm
303 mm
250 mm
|
245 mm
378 mm
306 mm
Weight| 1.8 kg| 2.6 kg| 3.5 kg| 5 kg
IP rating| IP 65
Ambient temperature| 0 – 40 °C
Subject to technical modification.
MONACOR INTERNATIONAL GmbH & Co. KG Zum Falsch 36 28307 Bremen Germany
Copyright© by MONACOR INTERNATIONAL. All rights reserved.