Woodbridge Tubs: Freestanding Bathtub User Guide & Installation Tips
- June 7, 2024
- WOODBRIDGE
Table of Contents
The Woodbridge Freestanding Bathtub User Guide provides detailed instructions for the installation and care of the product. The guide includes compliance with various codes and standards, tools required for installation, and important safety rules to follow when using the bathtub. The instructions must be observed for safe installation, and it is recommended that a fully insured and licensed plumber install the product. The guide also includes care and cleaning tips to maintain the acrylic surface, as well as repair and maintenance advice. The user guide emphasizes the importance of following the instructions to avoid any damages or injuries caused by incorrect handling or installation of the product. It also highlights that the limited warranty is void on any commercial installation and that the manufacturer, distributor, or retailer is not responsible for water damage or flood caused due to the use of this product. In case of any queries, customers can contact the Woodbridge customer service team via phone or email.
INSTALLATION AND CARE GUIDE
FREESTANDING BATHTUB
Compliance with the following codes& standard:
- 2015 Uniform Plumbing Code® ( UPC )
- 2018 International Plumbing Code® ( IPC )
- 2018 International Residential Code® ( IRC )
- CSA B45.5 / IAPM O Z124-2017- Plastic Plumbing Fixtures
READ ALL INSTRUCTIONSBEFORE UNPACKING THE PRODUCT
INSTRUCTIONSTHAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUSINJURY CAUSED BY
INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONSM UST BE
OBSERVED FOR SAFE INSTALLATION.
2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THISPRODUCT
This products must be installed by a fully insured and licensed plumber only.
Installation of any our product by anyone other than fully insured and
licensed plumber shall void limited warranty. We recommends that such licensed
plumber have experience in the installation of products.
Limited warranty is void on any commercial installation We are not responsible
for local code compliance for this product. Building and plumbing codes may
vary from state-to-state in accordance to your location. We are not resonsible
for providing any compliance certifications.
Under no circumstances we are shall not be liable for any and all incidental
damages sustained in connection with this product Neither manufacture, nor
distributor, nor retailer is responsible for water damage or flood caused due
to use of this product. Under no circumstances We shall not be liable for any
and all fees, cost of installa on/reinstalla on/removal, subsequent damage or
transportation in case of the product defect
Customer Service Phone: 562-229-0088. (Monday – Friday 9 AM – 5 PM Pacific Time) Or Email: help@woodbridgebath.com
TOOLS REQUIRED FOR INSTALLATION (NOT INCLUDED)
OTHER TOOLS MAY BE REQUIRED
Inspect the bathtub for any damages. If any damage is found please contact
your retailer.
Carefully, remove the tub from it’s crate/box.
Important Note: Bathtub must be carried by a minimum of 2 adult people in
upside down posion only. Do not carry the bathtub by its panel.
To avoid scratches or damages to the bathtub be sure to set it on cardboard
with so blanket on top of the cardboard.
Set your bathtub on two 4×4 pieces of lumber so you can have access from the
boom of the bathtub. Put a tray beneath the bathtub.
Very Important! Before proceeding with installation, please check that push
pop-up, drain, and integrated overflow are properly sealed and tightened.
Push the pop-up into a close position and fill the bathtub with cold water
above the overflow level to test for overflow leakage and drain leakage.
Check for any leaks around the drain and pipe. (NOTE: Due to surface tension,
it is normal for a small amount of water to pool around the drain)
If a leakage occurs please disassemble the drain line or overflow assemblies
and you can apply a plumbing puy/silicone caulk to fix the leakage.
Once the leakage test was performed you may proceed to the installation.
INSTALLATION WITH UNDERFLOOR ACCESS
-
Clean, level, and prepare the floor for installation, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with pencil and mark the drain hole location on the floor. Move the tub away so that the plumbing can be installed.
-
Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.
-
Place a level across the boom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additional 1/8” or 3/16” so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.
-
Install an 1-1/2″ tail piece along with the corresponing flanged washer and 1-1/2″ nut to thedrain body.
-
Measure and cut the tail piece to the appropriate length to reach the trap adapter When setting the tub drain, insert tail piece with 1-1/2″ slip joint and rubber washer into the trap adapter and tighten properly.
-
Apply a generous bead of adhesive or waterproof silicone to the boom of the tub and a bead of tub and tile caulk around the edge of the tub
-
Flip the tub over and carefully set the tub into posion with tail piece assembly to P-trap and connect to the drain.
-
Fill the tub with water to the overflow and then drain the tub while inspecng the waste and overflow connection below the floor for any leaks. Access from below will be necessary for this step.
-
With the tub now set in place, wipe off any excess tub or le caulking, adhesive where the tub meets the floor with wet cloth.
-
DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone sealant to dry.
Note:
If installing on a concrete slab where no underfloor access or cannot move drain. You may consider following opon.
- Optional flexible drain hose from plumbing hardware or home improvement store may be used (Woodbridge will not supply this flexible hose). Connect one end attaches to the bathtub drain and the other end needs to be attached to the floor drain by using a transition piece.
- Optional island tub drain may also be used.
- Create a bridge from bathtub drain to floor drain by cerfied plumber only because any mis-joint or loosen on connection will cause leaks.
INSTALLATION ON SLAB FLOOR (NO UNDERFLOOR ACCESS)
-
Clean, level and prepare the floor for installation on, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with pencil and mark the drain hole loca on on the floor. Move the tub away so that the plumbing can be installed.
-
Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches DG IDG on tub rim.
-
Place a level across the bottom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additional 1/8″ or 3/16″ so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.
-
Measure the actual distance from drain into drain pipe on floor and the drain pipe should extend approximately 1″ above the finish floor. Use a drain adapter (not provided) if necessary.
-
Clean the surrounding of the drain pipe with cloth in prepara on of setting the drain, the area should be dry and free of any debris. Apply a bead of clear silicon or plumber putty around the drain body and pass it through the drain hole, also apply plumber putty to the washer and slide it over the bottom of the drain body.
-
Install 1 ½” rubber slip gasket over the drain waste vent.
-
Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and caulk around the edge of the tub.
-
Flip the tub over and carefully set the tub into position with tail piece assembly to waste vent and connect to the drain.
-
With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.
-
DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone to dry.
IMPORTANT SAFETY RULES
ATTENTION! ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB
Warning The bathtub must be installed and used as described in this
manual
Warning Use caution when entering or exiting the bathtub
Warning Do not permit children or persons with infirmities to use the
bathtub without supervision of an adult
Warning People using any medications or having adverse medical history
must consult a physician prior to use of the bathtub to avoid potential
hyperthermia and possible drowning
Warning Water temperature over 100ºF may cause hyperthermia and/or other
health problems. Check water temperature and adjust it for your personal
comfort
Warning Never use bathtub while intoxicated, after taking meals or any
alcoholic beverages. Consuming alcoholic beverages before or during bathing
will cause drowsiness and may result in hyperthermia, loss of consciousness,
or even drowning
Warning If you are pregnant or you feel that you are may be pregnant,
consult your doctor before using the bathtub
Warning Never use any electrical devices such as hair dryer, lamp,
telephone, tv, radio, or others within 5 feet of the bathtub
Warning Do not overfill the bathtub before entering. Entering the bathtub
when filled will cause overflow and slippery conditions. Use extreme cau on
when entering and exiting
Care and Cleaning
- Most dirt will wash off with mild soap and warm water.
- For tough spots, use liquid dish washing soap or non-chlorine bleach.
- Do not use abrasive material such steel wool or scouring pads to clean the acrylic surface.
- Always test the cleaning solution on a small area before using it on the en surface.
- Do not allow cleaning to soak on the acrylic surface.
- Rinse thoroughly with water immediately and wipe dry with so cloth.
Repair and Maintenance
- Use liquid polish compound such as Gel-Gloss Kitchen and Bath Polish(TM) to keep the original shine of acrylic surface.
- Light scratches can be removed with polishing compound for automobiles.
- For deeper scratches use wet sandpaper (1500 grit or higher). Always add water when sanding and lightly sand the area larger than the scratch in a circular motion to remove the scratches. Repeat un l the scratch is removed. Use so cloth and small amount of polishing compound to restore shine. Repeat as needed un l surface shine is restored.
IMPORTANT!
DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and
simmilar solutions. Use of such solutions may cause corrosion, finish peeling,
and/or dull the surface.
DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired
brushes that will permanently scratch the surface.
Retain these installation instructions for future reference!
Please don’t hesitate to contact us if you have any questions or concerns.
Customer Service Phone: 562-229-0088.
(Monday – Friday 9 AM – 5 PM Pacific Time)
Or Email: help@woodbridgebath.com
www.woodbridgebath.com
SPECIFICATION
Product Specifications
Compliance with codes and standards:
– 2015 Uniform Plumbing Code® (UPC)
– 2018 International Plumbing Code® (IPC)
– 2018 International Residential Code® (IRC)
– CSA B45.5 / IAPM O Z124-2017- Plastic Plumbing Fixtures
Tools required for installation (not included):
– Other tools may be required
Care and cleaning:
– Use mild soap and warm water to clean
– For tough spots, use liquid dish washing soap or non-chlorine bleach
– Do not use abrasive materials such as steel wool or scouring pads
– Always test cleaning solution on a small area before using on the entire
surface
– Do not allow cleaning solution to soak on the acrylic surface
Repair and maintenance:
– Contact customer service for advice
FAQS
Who should install the Woodbridge Freestanding Bathtub?
The bathtub must be installed by a fully insured and licensed plumber only.
What tools are required for installation?
The tools required for installation are not included. Other tools may be required.
What should I do if I find any damage to the bathtub?
If any damage is found, please contact your retailer.
Can I carry the bathtub by its panel?
No, the bathtub must be carried by a minimum of 2 adult people in upside down position only.
How do I test for overflow and drain leakage?
Push the pop-up into a close position and fill the bathtub with cold water above the overflow level to test for overflow leakage and drain leakage.
What should I do if there is a leakage during the test?
If a leakage occurs, disassemble the drain line or overflow assemblies and apply a plumbing putty/silicone caulk to fix the leakage.
Can I install the bathtub myself?
It is recommended that a fully insured and licensed plumber installs the product.
How should I clean the acrylic surface of the bathtub?
Use mild soap and warm water for most dirt, liquid dishwashing soap or non- chlorine bleach for tough spots. Do not use abrasive materials such as steel wool or scouring pads.
Can I use electrical devices near the bathtub?
No, never use any electrical devices such as hair dryer, lamp, telephone, TV, radio, or others within 5 feet of the bathtub.
What should I do if I need repair or maintenance?
Contact the Woodbridge customer service team via phone or email for repair and maintenance advice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>