ColorKey CKU-5039 Mover Wash Hex 12 Moving Head Wash Light User Manual

: June 3, 2024
: ColorKey

Table of Contents

ColorKey CKU-5039 Mover Wash Hex 12 Moving Head Wash Light
Introduction
- Package Contents
- Service & Support
Display Operation
- Menu Guide
- DMX Values
Operation and Control
Troubleshooting
- Technical Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ColorKey CKU-5039 Mover Wash Hex 12 Moving Head Wash Light

Introduction

Package Contents

Mover Wash HEX 12
Power Cable
Hanging Brackets
User Manual

Caution
Opening this unit voids warranty. Contact Color Key for any service requests.
Warning
To avoid electrical shock, be sure to disconnect power before any service or when moving or setting up the fixture.
Caution
Avoid direct eye exposure with the fixture when on.

This fixture is for indoor use only.
Do not install or operate this fixture near flammable materials.
This device must be installed, operated, and maintained by a qualified professional.
Please check if the voltage is in accordance with the rated power before installing.
Do not operate this fixture if the power cord has been damaged. Turn off fixture and replace with a power cord of similar rating.

Service & Support

Your Color Key product includes a 2-year warranty. For technical support or to register your product, please visit https://www.colorkeyled.com/support/ You can also reach us by phone Monday thru Friday, 8:30am – 5pm PST at 818-578-4030.

Display Operation

Menu: Access the menu/Scroll through menu options (*Hold Menu for two seconds to exit the menu and return to your chosen program)
Up: Scroll through menu selections or increase parameters
Down: Scroll through menu selections or parameter decrease
Enter: Open/Select the current menu option

Menu Item	Values	Function
Addr	A001-A512	DMX Address setting
ChNd	9ch / 15ch	Channel selection mode
ShNd	Show0-Show4	Performance modes
SLNd	NASt / SLV1 / SLV2	Master / Slave settings
Soun	No/Yes	Sound active mode
SEnS	0-100	Sound active sensitivity
Blnd	No/Yes	Boot pause mode
Pan	No/Yes	X motor forward / reverse
Tilt	No/Yes	Y motor forward / reverse
LED	No/Yes	Display on / off during use
Disp	Yes / No	Invert the LED display
Bala	R:125-255,B:125- 255,G:125-255	White balance setting- Add or decrease

DMX Values

5 Channels Mode

Channel	Value	Function

1

| 000-007| Off
008-255| Dimmer (0 to 100)

2

3

9 Channels Mode

Channel	Value	Function
1	0-255	Pan motor adjustment
2	0-255	Tilt motor adjustment

3

| 0-199| Dimmer from dark to bright
200-250| Strobe from slow to fast
251-255| All bright
4| 0-255| Red
5| 0-255| Green
6| 0-255| Blue
7| 0-255| White
8| 0-255| Amber
9| 0-255| UV

15 Channels Mode

CH	Value	Function
1	0-255	Pan motor adjustment
2	0-255	Fine pan motor adjustment
3	0-255	Tilt motor adjustment
4	0-255	Fine tilt motor adjustment
5	0-255	Pan & Tilt speed
6	0-255	Dimmer from dark to bright (Ch 14 Must be Open)
7	0-255	Red
8	0-255	Green
9	0-255	Blue
10	0-255	Amber
11	0-255	White
12	0-255	UV
13	008-255	Auto color programs

14

Operation and Control

Fine tuning your Mover Wash Hex 12 start position
The Mover Wash HEX 12 offers the ability to adjust your starting position should your lights begin to vary after use due to bumps received during transit or use

To enter adjustment program, press Menu and hold Enter key for 3 seconds
Use Up and Down navigation arrows to select Pan or Tilt, pressing enter to make your selection.
You may now enter fine adjustments from -127 to 127 for both Pan and Tilt to start your light in its desired position.
Press Enter to confirm your selection and Menu to exit adjustments program.
Your Mover Wash will now start at desired position going forward.

Controlling your Mover Wash HEX 12 using a DMX controller:

Use a DMX cable to connect your Mover Wash HEX 12 to the DMX in/out sockets on the bottom of the light.
Set desired DMX address for your light

Using Master/Slave Mode:
The Master/Slave mode allows a group of Mover Wash HEX 12 units (the slaves) to duplicate the output of another Mover Wash HEX 12 (the master) without a DMX controller.

Set each of the slaves:
- Go to SLNd in the main menu and press enter.
- Select SL1.
Set the master:

Go to SLNd in the main menu and press enter.
Select NASt.
The master (NASt) is the unit that runs your program whether in one of the static color modes or various Auto programs.

Using Slave modes (SL1, SL2) to create a light show
Using 4 or more lights for best effect, Mover Wash HEX can help create auto- light shows by engaging Auto Programs on the Master fixture and having slaves connected in varying sequences to display varied yet synchronized light shows.

Set each of the desired slaves SL1, SL2:
- Go to SLNd in the main menu and press enter.
- Select SL1.
- Repeat steps for each slave fixture SL1 and SL2
Set the master:

Go to SLNd in the main menu and press enter.
Select NASt.
Accessing the (ShNd) programs on the Master light will now create varying displays of synchronized light on the master and slave fixtures through (Auto) and (SoUn) functions.

Troubleshooting

Problems	Solutions
No DMX Control	Ensure your DMX controller is sending signal and you are using

a proper and working DMX cable.
Head position is off centered at startup| See directions on pg. 7 “Fine tuning your Mover Wash Hex 12 start position”
Master / Slave| For a direct copy of the master (NASt), select SL1. For a synchronized yet varied Auto Show, select SL2.

Technical Information

12x12W RGBAW+UV LED Wash Light
DMX Channel Modes: 9 / 15 channels
Control modes: DMX 512, Master /Slave, Sound active, Auto programs
Pan: 540o
Tilt: 270o
Power consumption: 160W
Power supply: AC90-230V; 50-60Hz
Weight: 6.4lb
Measurements: 10.25in. x 7.14in. x 6.25in.

Please note: As we continue to work towards improving our products and your experience as a user, we recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at info@colorkeyled.com.