ColorKey CKU-3060 Battery Powered Lighting Package User Manual

June 1, 2024
ColorKey

CKU-3060 Battery Powered Lighting Package

CKU-3060
USER MANUAL

Please read these instructions carefully before use. Operating this fixture according
to these instructions is important to avoid any possible damage or accidents caused
by misuse.

Introduction

Package Contents

  • PartyBar Mobile 150
  • 7ft. Stand
  • Power Cable
  • IR Remote
  • Antenna x 2
  • QR Manual
  • Carrying Case
  • Mounting Brackets

Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or
when moving or setting up the fixture.

Service & Support

Your ColorKey product includes a 2-year warranty. For technical support or to register
your product, please visit https://www.colorkeyled.com/support/
You can also reach us by phone Monday thru Friday, 8:30am –5pm PST at 818-578-4030.

3 PartyBar Mobile 150 User Manual – V1

Stand Setup Instructions

PLEASE READ CAREFULLY BEFORE USING THE STAND TO AVOID  DAMAGE AND INJURY

The PartyBar tripod stand includes a removable extension pole, which has the advantage of shrinking the footprint of the stand when disassembled, for ease of  transportation. With the extension pole installed, the stand can lift your fixtures over 7ft  in the air.

To use the extension pole, simply press  the connection collar (B) to the top of
the tripod (A), then insert the extension  (C) into the collar. Push down until  both poles are fully inserted into the  collar and tighten the knob.

WARNING!  In order to avoid accidents, it is highly recommended to  weigh down the base of the tripod using counterweights or  sandbags while the stand is set to maximum height. Failure to do  so may result in the stand being tipped over accidentally, causing  damage and bodily injury.

4 PartyBar Mobile 150 User Manual – V1

Unpacking & Repacking

Please read these instructions carefully before packing. Packing this fixture according to these instructions is important to avoid any possible damage or accidents during transport and storage.

When packing your PartyBar Mobile 150 please be sure that:

• The unit is placed face down with derby fixtures pointing in a downward direction

• You remove wireless and footswitch antenna

• You remove mounting brackets

• The retainer strap does not hang out of case when closing the zipper

Mounting Orientation

PartyBar Mobile 150 may be mounted in any position; however, make sure there is  adequate ventilation around the product.

Rigging

• Before deciding on a location, make sure there is easy access to the product for maintenance and programming.

• Make sure adequate ventilation is provided around the product.

• Make sure that the structure or surface onto which you are mounting the product can support the products weight.

• Mount the product securely to a rigging point, weather an elevated platform or  a truss.

• When rigging the product onto a truss, use a mounting clamp of the appropriate weight capacity.

• When power linking multiple products, mount the products close enough for power linking cable to reach.

5 PartyBar Mobile 150 User Manual – V1

Product Overview

Front

  1.  Mounting Bracket
  2. RGBW 4-in1 LED Par
  3. Wireless DMX Antenna
  4. White+UV 2-in-1 LED
  5. Wireless IR Receiver
  6. Wireless Footswitch Antenna

6 PartyBar Mobile 150 User Manual – V1

Back

  1. Mounting Bracket
  2. Safety Eye-bolt
  3. Wireless DMX Antenna
  4. Battery Life Indicator
  5. Menu
  6. Microphone
  7. T3A Fuse Socket
  8. Locking Power In/Out
  9. DMX In/Out
  10. Power On/Off
  11. Wireless Footswitch Antenna

7 PartyBar Mobile 150 User Manual – V1

Display Operation

Menu: Access the menu/Scroll through menu options

Up: Scroll through menu selection or increase parameter

Down: Scroll through menu selection or parameters decrease

Enter: Open/Select the current menu option

8 PartyBar Mobile 150 User Manual – V1

Mode

|

Programming

|

Description

---|---|---

DMX

|

Addr

|

24 CH

|

d001-d512 for DMX addressing

12CH

3CH

Static colors

|

Stat

|

S 01-25

|

Static color selections

Auto

|

Auto

|

Au1-9

|

Auto programs

Sound

|

Soun

|

So1-9

|

Sound activated programs

Speed

|

SPEE

|

SP1-SP9

|

Speed select (slow to fast)

Sensitivity

|

SEnS

|

Se1-Se9

|

MIC sensitivity (low to high)

Dimming

|

dIMM

|

dI1-dI 9

|

Master dimming (low to high)

Silent scene

|

SILE

|

on/oFF

|

Specific to (Sound) mode, Silent Scene will  either keep the light on, or off when music stops  playing

Slave

|

SLAV

|

Slave

|

Slave mode will mimic Master units by way of  wired or wireless DMX connections. Select  SLAV for this control, otherwise the unit is a  Master

Wireless 2.4G

|

24G

|

1r__

|

Red or Ch. 1 Wireless Connection

2G

|

Green, Ch. 2 Wireless Connection

3rG_

|

Yellow, Ch. 3 Wireless Connection

4__b

|

Blue, Ch. 4 Wireless Connection

5r_b

|

Magenta, Ch. 5 Wireless Connection

6_Gb

|

Cyan, Ch. 6 Wireless Connection

7rGb

|

White, Ch. 7 Wireless Connection

ECO PRO

|

ECO

|

OFF

|

Regular operating mode at full brightness

ON

|

Energy saving mode, at a slightly reduced  brightness (to White+UV 2-in-1 LEDs)

S-EC

|

Super energy saving mode at a significant  reduction in brightness to strobe/UV inlay

Infrared

|

InFr

|

on/oFF

|

Enable or disable the IR remote

Foot

|

Foot

|

on/oFF

|

Enable or disable a Footswitch controller (sold  separately)

9 PartyBar Mobile 150 User Manual – V1

DMX Values

3CH DMX values

CH1

|

0-255

|

Master dimming (0-100%)

---|---|---

CH2

|

0-9

|

No function

10-19

|

Auto program 1

20-29

|

Auto program 2

30-39

|

Auto program 3

40-49

|

Auto program 4

50-59

|

Auto program 5

60-69

|

Auto program 6

70-79

|

Auto program 7

80-89

|

Sound program1

90-99

|

Sound program2

100-109

|

Sound program3

110-119

|

Sound program4

120-129

|

Sound program5

130-139

|

Sound program6

140-255

|

Sound program7

CH3

|

0-255

|

Auto and Sound Program 1-7 speed ( From slow to fast )

CH DMX values

CH1

|

0-255

|

Dimming

---|---|---

CH2

|

0-9

|

No function

10-255

|

PAR Stroboscope (Rate 0-100%)

|

PAR1-4

CH3-6

|

0-9

|

No function

10-19

|

Red

20-29

|

Green

30-39

|

Blue

40-49

|

White

50-59

|

Yellow

60-69

|

Magenta

70-79

|

Cyan

80-89

|

Dark orange

90-99

|

Green yellow

10 PartyBar Mobile 150 User Manual – V1

|

100-109

|

Salmon

|

---|---|---|---

110-119

|

Turquoise

120-129

|

Light Green

130-139

|

Orange

140-149

|

Straw

150-159

|

Lavender

160-169

|

Light blue

170-179

|

Dark blue

180-189

|

Pink

190-255

|

Full on

CH7

|

0-9

|

No function

|

Bar white LED

10-255

|

BAR white Stroboscope (Rate 0-100%)

CH8

|

0-9

|

No function

10-19

|

BAR white LED ON

20-159

|

LED Chase pattern cycling

160-255

|

LED Chase pattern (slow to fast )

CH9

|

0-9

|

No function

|

Bar UV LED

10-255

|

BAR UV Stroboscope (Rate 0-100%)

CH10

|

0-9

|

No function

10-19

|

BAR UV LED ON

20-159

|

LED Chase pattern cycling

160-255

|

LED Chase pattern (slow to fast )

CH11

|

0-9

|

No function

10-19

|

Auto program 1

20-29

|

Auto program 2

30-39

|

Auto program 3

40-49

|

Auto program 4

50-59

|

Auto program 5

60-69

|

Auto program 6

70-79

|

Auto program 7

80-89

|

Sound program1

90-99

|

Sound program2

100-109

|

Sound program3

110-119

|

Sound program4

120-129

|

Sound program5

130-139

|

Sound program6

140-255

|

Sound program7

CH12

|

0-255

|

Auto and Sound Program 1-7 speed ( From slow to fast )

11 PartyBar Mobile 150 User Manual – V1

CH DMX values

CH1

|

0-255

|

Master dimming (0-100%)

---|---|---

CH2

|

0-9

|

No function

10-255

|

PAR Stroboscope (Rate 0-100%)

CH3

|

0-255

|

Red (0-100%)

|

PAR1

CH4

|

0-255

|

Green (0-100%)

CH5

|

0-255

|

Blue (0-100%)

CH6

|

0-255

|

White (0-100%)

CH7

|

0-255

|

Red (0-100%)

|

PAR2

CH8

|

0-255

|

Green (0-100%)

CH9

|

0-255

|

Blue (0-100%)

CH10

|

0-255

|

White (0-100%)

CH11

|

0-255

|

Red (0-100%)

|

PAR3

CH12

|

0-255

|

Green (0-100%)

CH13

|

0-255

|

Blue (0-100%)

CH14

|

0-255

|

White (0-100%)

CH15

|

0-255

|

Red (0-100%)

|

PAR4

CH16

|

0-255

|

Green (0-100%)

CH17

|

0-255

|

Blue (0-100%)

CH18

|

0-255

|

White (0-100%)

CH19

|

0-9

|

No function

|

Bar white LED

10-255

|

BAR white Stroboscope (Rate 0-100%)

CH20

|

0-9

|

No function

10-19

|

BAR white LED ON

20-159

|

LED Chase pattern cycling

160-255

|

LED Chase pattern (slow to fast )

CH21

|

0-9

|

No function

|

Bar UV LED

10-255

|

BAR UV Stroboscope (Rate 0-100%)

CH22

|

0-9

|

No function

10-19

|

BAR UV LED ON

20-159

|

LED Chase pattern cycling

160-255

|

LED Chase pattern (slow to fast )

CH23

|

0-9

|

No function

10-19

|

Auto program 1

20-29

|

Auto program 2

30-39

|

Auto program 3

12 PartyBar Mobile 150 User Manual – V1

|

40-49

|

Auto program 4

---|---|---

50-59

|

Auto program 5

60-69

|

Auto program 6

70-79

|

Auto program 7

80-89

|

Sound program1

90-99

|

Sound program2

100-109

|

Sound program3

110-119

|

Sound program4

120-129

|

Sound program5

130-139

|

Sound program6

140-255

|

Sound program7

CH24

|

0-255

|

Auto and Sound Program 1-7 speed ( From slow to fast )

PartyBar Mobile 150 User Manual – V1

Stand Alone Control Settings

To use your PartyBar Mobile 150 without a DMX Controller, use one of the various  standalone modes below.

Static Color Programs

To run the PartyBar Mobile 150 in a Static color, do the following:

1. Press (Menu)

2. Use (Up) or (Down) to select Stat

3. Use (Up) or (Down) to select Color S 01- S 25

4. Press (Enter)

Automatic Programs

To run the PartyBar Mobile 150 in Automatic Mode, follow the instructions below: 1. Press (Menu)

2. Use (Up) or (Down) to select Auto

3. Use (Up) or (Down) to select show Au1-9

4. Press (Enter)

Sound Active Mode

To run the PartyBar Mobile 150 in Sound-Active mode, do the following:

1. Press (Menu)

2. Use (Up) or (Down) to select Soun

3. Press (Enter)

4. Use (Up) or (Down) to select So1-9

5. Press (Enter)

Sound Sensitivity

To set the Sound Active sensitivity on the PartyBar Mobile 150, follow the instructions below:

1. Press (Menu)

2. Use (Up) or (Down) to select SEnS

3. Press (Enter)

4. Use (Up) or (Down) to select sensitivity from Se1-Se9 (low to high)

5. Press (Enter)

14 PartyBar Mobile 150 User Manual – V1

Wired DMX Connections

Your unit will automatically be in Master mode unless menu option SLAV is selected  from the onboard display. To connect a Master to a Slave, you will need to link the  DMX (Out) of your Master unit to the DMX (In) of your Slave unit by a wired DMX connection.

Slave products:

To set Slave on the unit you wish to control from the Master, do the following:

1. Press (Menu)

2. Use (Up) or (Down)) to select SLAV

3. Press (Enter)

Using a DMX controller:

1. Power on your PartyBar Mobile 150

2. Connect to a DMX controller with a DMX cable plugged into the DMX (In) port of your  PartyBar Mobile 150 unit.

3. The fixture will default to DMX address 001.

a. The DMX address can now be set as needed for programing.

4. Use (Up) or (Down) to select (Addr)

5. Press (Enter)

6. Use (Up) or (Down) to select operating Channel Mode, (3ch, 12Ch or 24Ch) 7. Press (Enter)

8. Use (Up) or (Down) to set DMX Address (d001-d512)

9. Press (Enter)

15 PartyBar Mobile 150 User Manual – V1

Wireless DMX Connections

Your PartyBar Mobile 150 unit can connect wirelessly to other units using 2.4G wireless DMX networks 1-7. It can act as the Master controller or be controlled as  Slave, or by wireless DMX. To do so, follow the instructions below.

Wireless Network Overview:

1r__

|

Red or Ch. 1 Wireless Network

---|---

2G

|

Green, Ch. 2 Wireless Network

3rG_

|

Yellow, Ch. 3 Wireless Network

4__b

|

Blue, Ch. 4 Wireless Network

5r_b

|

Magenta, Ch. 5 Wireless Network

6_Gb

|

Cyan, Ch. 6 Wireless Network

7rGb

|

White, Ch. 7 Wireless Network

Slave products:

To set your units as SLAV you wish to control from the Master, do the following:

1. Press (Menu)

2. Use (Up) or (Down) to select SLAV

3. Press (Enter)

4. Use (Up) or (Down) to select 2.4G

5. Press (Enter)

6. Use (Up) or (Down) to select wireless network 1-7 (this will correspond to Master) 7. Press (Enter)

Master products:

To select wireless network, do the following:

1. Press (Menu)

2. Use (Up) or (Down) to select 2.4G

3. Press (Enter)

4. Use (Up) or (Down) to select wireless 1-7

5. Press (Enter)

6. Use standalone programs, Included IR remote or Optional footswitch to control.

16 PartyBar Mobile 150 User Manual – V1

Connecting to a wireless DMX transmitter:

To connect to a wireless DMX controller or other wireless network for control, do the  following:

1. Turn on your wireless DMX transmitter

2. Turn on your PartyBar Mobile 150

3. Press (Menu)

4. Use (Up) or (Down) to select 2.4G

5. Press (Enter)

6. Use (Up) or (Down) to select wireless 1-7

7. Press (Enter)

8. The fixture will default to DMX address 001.

a. The DMX address can now be set as needed for programing.

9. Use (Up) or (Down) to select (Addr)

10. Press (Enter)

11. Use (Up) or (Down) to select operating Channel Mode, (3ch, 12Ch or 24Ch) 12. Press (Enter)

13. Use (Up) or (Down) to set DMX Address (d001-d512)

14. Press (Enter)

17 PartyBar Mobile 150 User Manual – V1

IR Remote Overview

To use the IR remote, point the remote at the IR receiver on the lighting fixture while  pressing your desired selection. The IR receiver on the PartyBar Mobile 150 is  located on the front face of the unit.

*THE IR REMOTE WILL NOT WORK IF A DMX CABLE IS CONNECTED TO THE INPUT

BLACK OUT

1. Press BLACK OUT to clear the existing program mode- all lights will go off, Press BLACK OUT  again to return to the last program mode.

AUTO

1. Press AUTO on the IRC.

2. Press (+) or (–) to cycle between the different AUTO programs.

SOUND

1. Press SOUND on the IRC.

2. Press (+) or (–) to choose between the different SOUND programs.

STROBE

1. Press STROBE on the IRC.

2. Press (+) or (–) to adjust the strobe rate.

3. Press STROBE again to turn off the strobe.

SPEED

1. Press SPEED on the IRC.

2. Press (+) or (–) to adjust the auto/sound program speed.

SENSITIVITY

1. Press SENSITIVITY on the IRC.

2. Press (+) or (–) to adjust the microphone sensitivity value on the light.

DMX / %

1. Press to enable DMX or disconnect DMX on the product

2. Disconnecting DMX will set your fixture to last enabled program mode.

Manual

1. Press MANUAL on the IRC.

2. Press (R)ed, (G)reen, (B)lue, (W)hite, (A)mber and (UV/P) to choose your color setting.

3. Press (+) or (–) to cycle between static colors.

FADE / UNIT

1. Press Fade / Unit on the IRC.

2. Press (+) or (–) to cycle between the different FADE programs.

Numbers 0-9

1. Press from number (0) to (9) to change the brightness intensity (0 is low to 9 high).

18 PartyBar Mobile 150 User Manual – V1

Wireless Footswitch (Sold Separately)

AUTO SOUND COLOR BLACKOUT


Using the Optional Footswitch

• Ensure your PartyBar Footswitch Controller is powered on by engaging the power switch on the back of the unit and that the wireless antennae is securely  connected.

• Ensure the wireless antennae is also connected on the back of your  PartyBar Mobile 150 unit.

• Operate by pressing Auto, Sound Active, Color selections and Blackout. • When Blackout is pressed, the active program will discontinue. An additional press is needed to reengage the lighting fixture and enable the last program.

Enable the Footswitch Controller within the Menu:

1. Press (Menu)

2. Use (Up) or (Down) to select Foot

3. Press (Enter)

4. Use (Up) or (Down) to select On or Off

5. Press (Enter)

19 PartyBar Mobile 150 User Manual – V1

Battery Life and Specifications

PartyBar Mobile 150 features a rechargeable lithium-ion battery for wire free use. The  battery can power the light for up to 6 hours from a full charge.

The battery charges whenever the included power cable is connected and plugged into a power source. If the product is plugged in and not in operation, make sure the  product is turned off.

Battery life can be viewed on the rear of your unit above the LED Menu. ECO PRO  Power Saving can be enabled to extend the operating time of your fixture between  charges.

About ECO PRO PowerSaving

You can access Power Saving settings in the onboard LED menu.

• (OFF) Regular operating mode at full brightness

• (ON) Energy saving mode, at a slightly reduced brightness

• (S-EC) Super energy saving mode at a significant reduction in brightness

*Power usage still varies dependent on the complexity of the programs used.  About LED Indicators and Battery Life

You can view Battery Life remaining from LEDs above the onboard menu.

• Battery life 100%

• Battery life 75%

• Battery life 50%

• Battery life 25%

Battery specification:

• Maximum working hours: 3-6H (depends on the ECO PRO Power Setting and programs you choose )

• Battery charge time: 3 hours

• Battery lifetime: average lifetime is 500 charges

• Battery Type: Fixed Lithium Battery

• Battery Voltage: 11.1 VDC

• Battery Capacity: 4400 mAH

20 PartyBar Mobile 150 User Manual – V1

Maintenance

Dust build-up reduces light output performance and can cause overheating. This can  lead to reduction of the light sources’ life and or mechanical wear. To maintain optimum  performance and minimize wear, clean your lighting products regularly after extended  use. However, be aware that usage and environmental conditions could be contributing  factors to increase the cleaning frequency.

To clean the product, follow the instruction below:

1. Unplug the product from power.

2. Wait until the product is at room temperature.

3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on  the external surface/vents.

4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner,  or Isopropyl Alcohol.

5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue. 6. Softly drag any dirt or grime to the outside of the transparent surface.

7. Gently polish the transparent surfaces until they are free of haze and lint.

Troubleshooting

Problems

|

Solutions

---|---

No DMX Control

|

Ensure your DMX controller is sending signal and you are  using a proper and working DMX cable.

No Laser Output

|

Make sure the Laser Key is turned to ON

No Wireless

Connections are Made

|

Please follow instructions for wireless connections

21 PartyBar Mobile 150 User Manual – V1

Technical Information

• Par LEDs: (4) 4 x 4W RGBW 4-in-1 LED

• Bar LED: (4) 2W White+UV 2-in-1 LED

• Control Modes: DMX512, Master-Slave, Auto, Sound, IR Remote, Wi-DMX, Footswitch (Optional)

• 0-100% linear dimmer

• Flash rate: 0-20Hz

• DMX 3 / 12 / 24-channel mode

• DMX: 3-pin XLR In/Out

• Includes mounting brackets

• Power Input Type: PowerCon In + Out

• Power Consumption: 72W

• Power Supply: AC100~240V 50/60Hz

• Fuse: T3A

• Dimensions: 31.5 x 3.5 x 11.8 in.

• Weight: 12.25 lbs.

Please note: As we continue to work towards improving our products and your experience as a user, we recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at info@colorkeyled.com.

22 PartyBar Mobile 150 User Manual – V1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ColorKey User Manuals

Related Manuals