ColorKey CKU-7700 Dazzler FX Cold Spark Machine User Manual

: June 3, 2024
: ColorKey

Table of Contents

ColorKey CKU-7700 Dazzler FX Cold Spark Machine
Introduction
Installation
Maintenance & Precautions
Service & Support
Menu Guide
Wireless Remote Overview
Operation
Troubleshooting
Technical Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ColorKey CKU-7700 Dazzler FX Cold Spark Machine

Introduction

Package Contents

Dazzler FX Cold Spark Machine
PowerCon Locking Power Cable
Remote
Remote Receiver
User Manual

Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.

Warning!

To avoid electrical shock, be sure to disconnect power before any service or when moving or setting up the fixture.
Always keep this fixture in a dry area
This fixture must be used at a minimum distance of 5 meters (16’4”) away from any contactable objects.
Do not install or operate this fixture near flammable materials.
This device must be installed, operated, and maintained by a qualified professional.
Please check if the voltage is in accordance with the rated power before installing.
Do not operate this fixture if the power cord has been damaged. Turn off fixture and replace with a power cord of similar rating.
Do not touch the fixture during operation as the housing heats up

Installation

Ensure there are no flammable materials within 5 meters (16’4”) of the fixture
Connect the fixture to power and turn on

Maintenance & Precautions

Dazzler FX must be cleaned after each use to extend the life of the unit. Use the
Clearing function (IR Remote option (6), DMX Ch2; set at 150-255) to expel unspent powder after each use.
Ensure that you are using ColorKey Dazzler FX Cold Spark Powder [CKU-7800] (Sold separately)
Be sure to keep track of wireless Remote receiver. If it gets lost, you will need to contact ColorKey

Service & Support

Your ColorKey product includes a 2-year warranty. For technical support or to register your product, please visit https://www.colorkeyled.com/support/ You can also reach us by phone Monday thru Friday, 8:30am – 5pm PST at (818) 578- 4030.

Dazzler FX Overview

LCD Display Operation

Menu: Access the menu/Scroll through menu options
Up: Scroll through menu selection or increase parameter
Down: Scroll through menu selection or parameters decrease
Enter: Open/Select the current menu option

Menu Item Show	Values	Function
DMX Address	001-512	DMX Address setting
Wireless Switch	On / Off	Turn the Wireless Remote On or Off
Language	CN / EN	Switch between English and Chinese
Master	On / Off	When Multiple units are connected in series, set one unit as

the Master. The Master can be controlled by the remote and control and connected units will respond accordingly
ID Code| 01-30| When machines are connected in series, set each with a unique ID Code to allow for Master/Slave pre- programed FX shows such as “Horse Race”. The first unit should be 001, the next 002 and so on.

THE MAXIMUM NUMBER IS 30.

PaoMA| 01-30| This is the number of machines to be connected in series. For example, if only using 8 units in series set all Master and Slave units to 008.

THE MAXIMUM NUMBER IS 30.

Class switch (Spray Effect)| On / Off| The fan and spray effect will only operate when Class is On
Class (Spray

height)

| 1, 2, 3| 1-Low spray height, 2-Medium spray height,

3-High spray

Manual Spark| On / Off| Use this function to troubleshoot the machine if you encounter any issues during use.
Display Protect| On / Off| Automatically blackout the screen after 30 seconds of

non-use

DMX Values

Channel	Value	Function
1	0-10	Spark Off
11-255	Spark On
2	0-149	No Effect
150-255	Clear Material (Blower only, no heat) Recommended after

each use.
3| 0-199| Heating on (Ch1 functions will not work)
200-255| Stop heating (Ch1 functions will not work)

*NOTE: The “Stop heating” function can be useful when a machine needs to be part of a live event setting for an extended time while remaining cool.

Wireless Remote Overview

Button	Function	Description
1	Turn On	Spark On
2	Turn Off	Spark Off
3	High	Maximum spark fountain height
4	Medium	Medium spark fountain height
5	Low	Minimum spark fountain height
6	Clear Powder	Run for 5 seconds to clear Dazzler FX Spark Powder
7	5s Show	Will produce a 5-second show at Class setting
8	10s Show	Will produce a 10-second show at Class setting
9*	Sigle FX Auto	See page 11 “ **Horse Racing Effects using the Master

Slave settings** ” for instructions for enabling multi-unit Auto FX.

More than one Dazzler FX is needed to run Auto FX

Read Before First Use

At power on, the Dazzler FX will begin heating for use. It is recommended to connect to your selected DMX controller and other machines at this time.
The Dazzler FX must be used in a well-ventilated area only. If the machine is placed in too hot an environment (above 104 degrees) where there is limited airflow, the machine’s heating protection system may cause a safety shutdown.
The Dazzler FX machine must be used horizontally on the ground only. The machine should have 1 meter (3 feet) clearance on all sides. Keep away from children, flames, flammable, and combustible materials.
Don’t allow the Dazzler FX machine to run out of powder for an extended time. If the machine is allowed to run empty, it may cause the motor and heater to be damaged.
Turn off the power before adding powder and do not allow powder to enter the inside of the housing as internal electrical damage may result.
If the spark output is low, or there is noise from motor, or the machine stops creating spark altogether- do not attempt modify or repair the machine by yourself.
Please contact the dealer of purchase of ColorKey directly for more support.
To better protect the life and longevity of your Dazzler FX units, it is advised to use the effect in small increments of 10-30 seconds. If the machine continues to work, heat up and consumes a whole package of powder, please cut off the power and make the machine stop working for more than 10 minutes.
When the machine is not being used, or will be in storage for a long time, please do not keep the powder loaded in the tank. Please be sure to spray out the powder using the remote, manual or DMX clearing functions to prevent the machine from becoming blocked or lodged with powder.
When finished loading Dazzler FX Spark Powder, be sure to securely fasten the Storage Tank cap, otherwise it could allow for safety issues.
The power supply can connect to a maximum of 6 machines in series.
If the machine is overturned or impacted during use, it will automatically shut down.
To correct, turn off the power, check all connections are not damaged. When confirmed ok, it can be used normally after restarting

Operation

Using the Wireless Remote

Plug in the power cord and power on. Wait for the machine to warm up for 3-5 minutes, the ‘heating’ indicator will flash during warm up.
Ensure the Wireless Receiver is connected to your Dazzler FX and Wireless is turned On in the main menu. The remote has a power switch located on the right side and uses a A123 battery (included).
When the heating indicator light stops flashing to signal that the machine has finished preheating, pour Dazzler FX Spark Powder into the storage tank. (We recommend using about half a bag of powder at a time)
You may now use the remote control to trigger spark effects. (See page 9 for remote control details).

Horse Racing Effects using the Master Slave settings:

Using the Menu, set your desired “Master” unit to the “ON” state.
Select “PaoMa Num” and set it to the TOTAL number of connected machines.
For example, if 4 machines are connected in series, the value is set to 004.
The host “ID code” is set to 001 by default.
To Slave machines, enter the Menu setting interface and set the second “ID code” to “002”. In turn the third will be set to “003”, and so on…
After the settings are completed, use the remote control’s Multi Unit buttons “9,10,11 …16” will now work to trigger the various multi-unit Dazzler FX spray FXs.

Using a DMX controller:

Power on the machine and connect to a DMX controller with a DMX cable.
The machine defaults to DMX address 001. The DMX address can now be set as needed.
Dazzler FX preheating starts instantly when plugged in. When the preheating is complete, the heating indicator will stop flashing. You can then push channel 1 to start spraying and adjusting the height.
To turn off the machine’s continuous heating feature, engage Channel 3 DMX value to 200-255.
Use Channel 2 to start the blower only and clear unused Dazzler FX Spark Powder

Set Spray Height (Use for manual testing only):

NOTE : These settings are used for manual testing only, we strongly suggest not to modify the “Class” settings on the Menu Select “Setting” and press “ENTER” to enter the Setting Menu. Select “Gear” and switch to “On”. Gear associates to height as follows: (1) is low, (2) is medium, and (3) is the highest spray height (approx. 5m).

Troubleshooting

Problems	Solutions
No DMX Control	Ensure your DMX controller is sending signal and you are using

a proper and working DMX cable.
Error Light Indicator On| If the error light indicator is on, please ensure your Dazzler FX is in the correct upright position. Restart to

test.

If the fan is working but no spark| If the fan of the machine is working but the Dazzler FX does not spray sparks, please ensure the machine is fully preheated. (The heating indicator will no longer flash and remain solid when Dazzler FX is fully warmed up)

Technical Information

600W Cold Spark Machine with FX
DMX Channel Modes: 3 channels
Control modes: DMX 512, Master /Slave, Wireless Remote
Screen Display: LCD
Pre-heating time: 3 min
Spark Height: 1.5 – 5 meter adjustable
Power connection: PowerCon In / Out
Power consumption: 600W
Power supply: AC120-240V; 50-60Hz

Please note: As we continue to work towards improving our products and your experience as a user, we recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at info@colorkeyled.com.