ColorKey CKU-5038 Mover Halo Beam QUAD MKII User Manual

June 5, 2024
ColorKey

ColorKey CKU-5038 Mover Halo Beam QUAD MKII User Manual
ColorKey CKU-5038 Mover Halo Beam QUAD MKII

Introduction

Thank you for purchasing the ColorKey Mover Halo Beam QUAD MKII. Please read these instructions carefully before use. Operating this fixture according to these instructions is important to avoid any possible damage or accidents caused by misuse.

Packing list

  • 1x Mover Halo Beam QUAD MKII moving head fixture
  • 1x Bracket
  • 1x Power cord
  • User Manual

Safety

Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.

  • This fixture is for indoor use only.
  • This fixture must be installed a minimum distance of 5 meters (16’4”) away from any lighted objects.
  • Do not install or operate this fixture near flammable materials.
  • This device must be installed, operated, and maintained by a qualified professional.
  • Do not touch the fixture with bare hands during operation as the surface temperature of the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to cool before attempting to touch it.
  • Please check if the voltage is in accordance with the rated power before installing.
  • Do not operate this fixture if the power cord has been damaged. Turn off fixture and replace with a power cord of similar rating.

Display Operation

  • MENU: Access the menu/Scroll through menu options
  • ENTER: Open/Select the current menu option
  • UP: Scroll through menu selection or parameter increase
  • DOWN: Scroll through menu selection or parameters decrease

Menu Guide

Addr| A001- A512| DMX512 address
CHnd| 16CH| 16channel setting
14CH| 14channel setting
SLnd| Auto| Auto mode(master)
Soun| Sound mode(master)
SL 1| console mode
SL 2| slave mode

ID| ID00-ID15| ID setting

SHnd| SH 0| effect 0 (recommended)
SH 1| effect1
SH 2| effect2
SH 3| effect3

SEnS| 0-99| Sensitivity adjustment

bLAnd| bLAc| 0(no DMX signal)
Auto| Auto mode(no DMX signal)
Soun| Sound mode(no DMX signal)
HoLd| stays on the latest console scene(no DMX signal)

LEd| OFF| Display turns off after 5 seconds
ON| Display stays on

dISP| no| Display Up
YES| Display Down

rPAN| no| Forward rotation (PAN)
YES| Backward rotation (PAN)

rTiL| no| Forward rotation (TILT)
YES| Backward rotation (TILT)

REST| YES| System reset

DMX Values

16 Channel Mode

Channel Value Function
1 0-255 Pan (Coarse)
2 0-255 Pan (Fine)
3 0-255 Tilt (Coarse)
4 0-255 Tilt (Fine)
5 0-255 Rotation Speed
6 0-255 Dimmer
7 0-255 Strobe
8 0-255 Red dimming
9 0-255 Green dimming
10 0-255 Blue dimming
11 0-255 White dimming
12 0-255 Color chase
13 0-255 Ring Color / Chasing Effect
14 0-255 Auto (motor: Pan/Tilt)
15 0-255 Chase speed
16 250-255 Reset (5seconds)

14 Channel Mode

Channel Value Function
1 0-255 Pan (Coarse)
2 0-255 Tilt (Coarse)
3 0-255 Rotation Speed
4 0-255 Dimmer
5 0-255 Strobe
6 0-255 Red dimming
7 0-255 Green dimming
8 0-255 Blue dimming
9 0-255 White dimming
10 0-255 Color chase
11 0-255 Ring Color / Chasing Effect
12 0-255 Auto (motor: Pan/Tilt)
13 0-255 Chase speed
14 250-255 Function

DMX Connections

DMX Cable:
This fixture can be controlled via DMX using a 3-pin XLR connection. The standard DMX connection is XLR is: one end connects to the male plug, and the other connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal

DMX Connections
DMX Connections

Noted: In order to avoid failures and interference signal transmission,we connect a resistance120Ω(1/4W)at the end of the DMX connecting as below:

DMX Connections

The Conversion between 3 pin and 5 pin XLR

If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

3-Pin XLR to 5-Pin XLR Conversion

Conductor| 3-Pin XLR Female (Out)| 5-Pin XLR Male (In)
Ground/Shield| Pin 1| Pin 1
Data Compliment (- signal)| Pin 2| Pin 2
Data True (+- signal)| Pin 3| Pin 3
Not Used| | Do Not Use
Not Used| | Do Not Use

Master/Slave Mode Operation

Master/Slave

Master/Slave mode allows you to connect multiple units together using one (1) unit to control others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal interference, do not connect DMX when using Master/Slave mode. If using a DMX run longer than 60 meters and/or over 32 units, a signal amplifier may be required.

Please note that Mover Halo Beam QUAD MKII will only work with other Mover Halo Beam QUAD MKII models and not the first generation model.

Troubleshooting

Problem Solutions
No DMX control Make sure that the DMX cable is properly connected

Make sure that the DMX controller is operational
Check the DMX cable for tears or breaks
Make sure that the fixture is in DMX mode
Fixture does not respond to sound| Make sure that the fixture is in Sound Active mode.

Technical Information

Beam: 40W RGBW 4-in-1 LED
Ring: 12x 5050 RGB 3-in-1 SMD LEDs
Independent DMX control of beam and ring effects
Beam angle:
Built-in auto/sound active programs
Digital dimmer and strobe
Pan: 540°
Tilt: 270°
Pan/tilt invert
16/30 channel DMX modes
Power consumption: 70W
Working Environment: Indoor, -4˚F to 104˚F (-20℃ to 40℃)
IP Grade: IP20
Power Supply: AC 100-240V/50-60Hz
3-pin DMX connections
IEC power connection
Size: 11.4”x8.25”x8.25” (29x21x21 cm)
Weight: 6.6 Lbs. (3kg)

Warranty

Notice to consumer: ColorKey offers a 2-year limited warranty. Please visit our website at www.ColorKeyLED.com to register your product.

Please note: We recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at info@colorkeyled.com.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ColorKey User Manuals

Related Manuals