ColorKey CKU-5037 Mover Miniwash QUAD 4 MKII User Manual
- June 6, 2024
- ColorKey
Table of Contents
ColorKey CKU-5037 Mover Miniwash QUAD 4 MKII
Introduction
Thank you for purchasing the ColorKey Mover Miniwash QUAD 4. Please read these instructions carefully before use. Operating this fixture according to these instructions is important to avoid any possible damage or accidents caused by misuse.
Packing list
- 1x Mover Miniwash QUAD 4 moving head fixture
- 1x Bracket
- 1x Power cord
- User Manual
Safety
Caution! Opening this unit voids the warranty. Contact ColorKey for any
service requests. Warning! To avoid electrical shock, be sure to disconnect
power before any service or when moving or setting up the fixture.
Caution! Avoid direct eye exposure with the fixture when on.
- This fixture is for indoor use only.
- This fixture must be installed a minimum distance of 5 meters (16’4”) away from any lighted objects.
- Do not install or operate this fixture near flammable materials.
- This device must be installed, operated, and maintained by a qualified professional.
- Do not touch the fixture with bare hands during operation as the surface temperature of the fixture can exceed 60˚C (140˚F). Turn off the power and wait 15 minutes for the fixture to cool before attempting to touch it.
- Please check if the voltage is in accordance with the rated power before installing.
- Do not operate this fixture if the power cord has been damaged. Turn off the fixture and replace with a power cord of a similar rating.
Display Operation
- MENU: Access the menu/Scroll through menu options
- ENTER: Open/Select the current menu option
- UP: Scroll through menu selection or parameter increase
- DOWN: Scroll through menu selection or parameters decrease
Menu Guide
| Addr | A001-A512 | DMX 512 |
|---|---|---|
| CHnd | 14CH | 14 channel |
| 16CH | 16 channel | |
| Inu | Pan | X-axis (motor) forward/backward running(PAN) |
| tlLe | Y-axis(motor) forward/backward running(TILT) |
Stat
| CH01| Channel 1(Manual)
CH02| Channel 2(Manual)
–
–
–
| –
–
–
CH16| Channel 16(manual)
Auto
| Aut1| Auto1
Aut2| Auto2
Aut3| Auto3
Aut4| Auto4
Soun
| Sou1| Sound active 1
Sou2| Sound active 2
Sou3| Sound active 3
Sou4| Sound active 4
Sou5| Sound active 5
REST| YES| Reset
dISP| no| Backward display (LED display)
YES| Forward display (LED display)
DMX Values
14 Channel mode
| Ch | Function | Value |
|---|---|---|
| 1 | PAN running | 0-255 |
| 2 | TILT running | 0-255 |
| 3 | Speed adjustment | 0-255 |
| 4 | Dimmer | 0-255 |
| 5 | Strobe (from slow speed to fast speed) | 0-255 |
| 6 | Red dimming | 0-255 |
| 7 | Green dimming | 0-255 |
| 8 | Blue dimming | 0-255 |
| 9 | White dimming | 0-255 |
10
|
Motor
| 0-15 (no function)
16-128 (fast speed Auto running & “sound active function” off)
129-255 (slow speed Auto running & “sound active function” on)
11| Sensitivity adjustment (Sound active)| 0-255
12
|
Colors
| 0-140 (change colors)
141-255 (sound active with changing colors)
13| Colors changing speed adjustment| 0-250
14| No function| 0-249
Reset| 250-255
16 Channel mode
| Channels | Function | Value |
|---|---|---|
| 1 | PAN running | 0-255 |
| 2 | Hint adjustment (PAN) | 0-255 |
| 3 | TILT running | 0-255 |
| 4 | Hint adjustment (TILT) | 0-255 |
| 5 | Speed adjustment | 0-255 |
| 6 | Dimmer | 0-255 |
| 7 | Strobe (from slow speed to fast speed) | 0-255 |
| 8 | Red dimming | 0-255 |
| 9 | Green dimming | 0-255 |
| 10 | Blue dimming | 0-255 |
| 11 | White dimming | 0-255 |
12
|
Motor
| 0-15 (no function)
16-128 (fast speed Auto running & “sound active function” off)
129-255 (slow speed Auto running
& “sound active function” on)
13| Sensitivity adjustment (Sound active)| 0-255
14
|
Colors
| 0-140 (change colors)
141-255 (sound active with changing colors)
15| colors changing speed adjustment| 0-250
16| No function| 0-249
Reset| 250-255
DMX Connections
DMX Cable：
The Mover Miniwash QUAD 4 can be controlled via DMX using a 3-pin XLR
connection.
The standard DMX connection is XLR is: one end connects to the male plug, and
the other connects to the female. As below: pin 1: ground, pin 2: negative
signal, pin 3: positive signal 
Noted: In order to avoid failures and interference signal transmission，we connect a resistance120Ω （ 1/4W ） at the end of the DMX connecting as below:
The Conversion between 3 pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable
Master/Slave Mode Operation
Master/Slave
Master/Slave mode allows you to connect multiple units together using one (1)
unit to control others in a chain. When a fixture is set to ‘Master Mode,’
this unit will always act as a controlling unit until it is switched out of
‘Master Mode’. The Master unit will send out signal via DMX to Slave units
which will react in synchronization. When a fixture is set into ‘Slave Mode’,
this fixture will receive the Master signal. To avoid master signal and DMX
signal interference, do not connect DMX when using Master/Slave mode. If using
a DMX run longer than 60 meters and/or over 32 units, a signal amplifier may
be required.
Please note that Mover Miniwash QUAD 4 MKII will only work with other Mover
Miniwash QUAD 4 MKII models and not the first generation model
(CKU01-5033).
Troubleshooting
| Problem | Solutions |
|---|---|
| No DMX control | □ Make sure that the DMX cable is properly connected |
□ Make sure that the DMX controller is operational
□ Check the DMX cable for tears or breaks
□ Make sure that the fixture is in DMX mode
Fixture does not respond to sound| □ Make sure that the fixture is in Sound Active mode.
Technical Information
- Power supply: AC110V-240V; 50-60HZ
- Power consumption: 60W
- Light source: 4 x 12W 4-in-1 LED’s (RGBW)
- Life span: up to100,000 hours
- Beam Angle: 25˚
- Channel: 14ch/16ch
- Control: Auto, Sound active, DMX512, Master/slave
- Pulse frequency: 0-10HZ
- Dimming: 0-100%
- Pan: 540˚
- Tilt: 270˚
- IP rate: IP20
Notice to the consumer: ColorKey offers a 2-year limited warranty. Please visit our website at www.ColorKeyLED.com to register your product.
Please note: We recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at info@colorkeyled.com.