LUTRON HomeWorks System Architecture for 120VAC and 434MHz regions User Guide

LUTRON Home Works System Architecture for

 _ **120VAC and 434MHz regions User Guide**_

Homework’s System Capacities

• 1 processor and up to 15 additional processors/gateways (maximum of 16 total devices)

• 32 configurable links (max)
  – 32 QS wired links (max) –
  15 Clear Connect – Type A links (max)

• 10,000 zones2 (max)

1device — Any system component that requires a single address. The processor reserves a single address on every link. Four addresses are reserved for hybrid repeaters on the wireless link.
2zone — An output. An individual shade or dimmer/QSG/contact closure output. Example: A GRAFIK Eye QS would be one device that could have up to six zones.

Key – Wiring

GRX-CBL346S-500 Two pair: one pair #18AWG one pair #18–22AWG twisted shielded
Pin-out: pin 1 – common, pin 2 – VDC, pin 3 – MUX, pin 4 – MUX
The wire gauge required for shade power conductors is dependent on shade size and number, wire run length, and power supply type being used.
Consult technical specifications of shade equipment for details.
One pair 22AWG twisted, shielded, Class 2 wires (max home run 500ft. per local control, not to exceed 1000ft. total per bus).

Home Works Processor

• Processor link — 2 RJ-45 Ethernet ports with built in switch for daisy chaining processors (1 RJ-45 Port with HQP7-1)
• Configurable links (RS-485) HQP7-2 offers two configurable links; HQP7-1 offers one configurable link. – QS wired link – QS wireless link (Clear Connect – Type A)
• 24 -35 VDC powered
• Mounts in low-voltage enclosures, PD4, and PD8 DIN panel

Key – Power

1. Line voltage 120 VAC
2. Low voltage 24 VAC
3. Low voltage 24-35 VDC
4. Low voltage 12 VDC
5. Plug-in transformer
6. Battery powered
7. Power over Ethernet (PoE)

• Standard Ethernet wiring (328 feet max) used to connect processors to network
• 10/100 Mbit Ethernet

• 100 devices per gateway
• 40 G2 Linear fixtures per N3
• 100 ft. total run off of N3 including G2s (max.)
• X96 controller can be mounted 50 feet away from the devices
  – Lightbar Slim High Output and Lightbar Slim Uniform Lens can be max. of 15 ft. long
  – Lightbar Slim Long Run can be a max. of 24 ft.

• 100 devices1 per link
• 512 zones2 per link
• 2,000 feet maximum wire length (consult technical specs for other applicable rules)
• Free-wire topology (star, daisy chain, home run, etc.)
• Standard Lutron 4 conductor cable*

• 100 devices1 per link (includes repeaters)
• 100 zones2 per link
• 4 repeaters per link
• RF distance—60ft from repeater to repeater, 30ft from device to repeated

© 05/2021 Lutron Electronics Co., Inc. P/N 368-2617 REV O (Non-Orderable) The Lutron logo, Lutron, Alissa, Architrave, GRAFIK Eye, Home Works, Ivalo, Kera, Palladium, Pico, Radio Power Saver, see Touch, and Silvia QS are trademarks or registered trademarks of Lutron Electronics Co., Inc., in the U.S. and/or other countries. Apple is a trademark of Apple Inc., registered in the U.S. and other countries. Android is a trademark of Google Inc. Use of this trademark is subject to Google permissions.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>