ULINE H-2065 Deluxe Impulse Sealer with Cutter User Guide

H-2065
DELUXE IMPULSE SEALER WITH CUTTER

1-800-295-5510
uline.com

TECHNICAL DATA

Types of films: LDPE, HDPE, PP, PVC, BOPP.

OPERATION

IMPORTANT! Read this manual thoroughly and familiarize yourself with ALL controls and operating features. Keep this manual for future reference and maintenance.
The machine should be located and operated in a dry room with good ventilation, and away from any flammable materials and gases.
SETUP
The machine is ready for operation after it is plugged into an approved 115VAC electrical outlet and the yellow LED illuminates. (See Figure 1A) Before the operation, adjust the sealing time to match the film’s type and width by conducting a test sealing:

1. Set the regulator button to the lowest setting (#1 setting). (See Figure 1B)
2. Place film between sealing head and sealing electrode.
3.  Close sealing head, hold down handle and wait for end of sealing cycle. LED changes from yellow to red while the machine is sealing.
4. When sealing is complete, the LED changes from red to yellow.
5. Allow seal to cool down for 1-2 seconds and lift handle.
6. If bag is not fully sealed, increase the sealing time by turning the regulator button to higher setting and repeat steps 2-5.

NOTE : The quality of the seal depends on the thickness of the film and its composition. Test sealing should always be conducted at a low setting. If necessary, sealing time can be increased in small steps.
NOTE: To achieve the best seal, keep the handle down for a few seconds after the sealing operation is complete. This allows the seal to cool down under pressure and become permanent.
WARNING! Sealing at a higher temperature than necessary may result in premature wear of parts and excessive melting of packaging material.
USING THE CUTTING KNIFE
For safety reasons, the knife is secured in position by a spring. To cut the film, press down on the knife and move it back and forth.
NOTE: For best results, first press the knife head down in the middle of the sealed film and slide it back and forth. This helps prevent film breakage on the sides. (See Figure 2)

WARNING! To prevent injury, never operate the knife head when the sealing bar is open. Before using, always ensure that the knife is intact and positioned correctly.

MAINTENANCE

CLEANING
The machine does not require special care. However, it is advisable to remove any residue from the sealing head and silicone rubber before it burns on. Use a damp, wet cloth to clean. Do not use cleaning products that contain solvents.
REPLACING WORN PARTS
Only use Uline replacement parts.
REPLACING THE PTFE TAPE AND SEALING WIRE
To replace the PTFE tape and sealing wire:

1. Remove upper PTFE tape (See Figure 3A) and unscrew fastening screws on side of the sealing electrode. (See Figure 3B)
2. Remove safety caps from sealing wire tensioning units. (See Figure 3C)
3. Carefully pull sealing wire up and remove it from the machine. (See Figure 3D)
4. Remove PTFE tape attached to the machine. (See Figure 3E)

NOTE: When changing the PTFE tape, always ensure the tape under the sealing wire is intact. While changing the sealing wire, it is advisable to install the protective cap backward on the sealing wire tensioning unit.

WARNING! For safety, used or burned PTFE tape should be replaced immediately.
WARNING! To prevent an electrical short, cut each side of the lower self- adhesive PTFE tape 4 mm (about 1/8″) longer than the aluminum side panel of the machine.
WARNING! Never apply tape to the surface of the sealing wire. It must move freely under the upper PTFE strap. (Only a portion of the upper strap is treated with adhesive.)

REPLACING THE SILICONE RUBBER
Pull out the damaged or burned silicone rubber from the sealing bar and clip in the new silicone rubber. (See Figure 4) When installing the silicone rubber, observe the direction of the profile.
NOTE: It is not necessary to pull the silicone rubber through the profile. It can be clipped in easily.
WARNING! When changing the silicone rubber, use caution around the sharp knife in the sealing bar’s knife assembly. (See Figure 4)

REPLACING THE KNIFE
To replace a blunt, dull or broken knife:

1. Lift sealing bar and press down on the head of knife assembly.
   (See Figure 5A)

2. Pull the knife out of its housing with pliers. (See Figure 5B)

3. Insert a new knife.

REPLACING THE KNIFE ASSEMBLY
To replace a worn or damaged knife assembly:

1. Remove front cap in front side of sealing bar as it opens. (See Figure 6A)
2. Loosen screws that hold the handle and remove. (See Figure 6B)
3. Detach screws that fasten the sealing head. (See Figure 7A)
4. Remove spreader from aluminum profiles. (See Figure 7B)
5. Pull out old knife assembly and replace. (See Figure 8A)
6. Reinstall the sealing head by performing steps 1-5 in reverse order.

NOTE: Always replace the front cap, the machine will not operate without it.

TROUBLESHOOTING

connected to an electrical outlet.

Is the outlet “live?”

Check if the control panel is damaged.

LED lamp illuminates yellow but does not change to red when the handle is closed. Machine does not seal.| Ensure that sufficient force is used to press the handle down. (Do not press the handle sideways.)

Is the front cap on the handle? Is the magnet inside it?

Check if the control panel is damaged.

LED lamp illuminates normally, but the machine does not seal.| Unplug from power immediately. Ensure sealing wire, PTFE tapes, and transformer are intact.
Sealing is not acceptable.| Change sealing time with regulator button. (Sealing time increases proportionally with the thickness of the film.)

After sealing, allow 1-2 sec. to cool. (Cooling time increases proportionally with sealing time.)

Loose handle.| Tighten hinge bolts.
Sealing wire heats up immediately when the machine is plugged in.| Check if the control panel is damaged.
Immediately unplug from electrical power and call Uline at 1-800-295-5510.

TECHNICAL INFORMATION

TYPE| SEALING
LENGTH| MAX. FILM
WIDTH| CUTTING
LENGTH| MACHINE
DIMS| NET
WEIGHT
---|---|---|---|---|---
H-2065| 12.60″| 11.81″| 11.81″| 20.99 x 3.95 x 6.89″| 7.9 lbs.
TYPE OF
TRANSFORMER| PRIMARY/SECONDARY
NOMINAL VOLTAGE| NOMINAL
ELECTRIC POWER| NOMINAL
CURRENT| USED FUSES
---|---|---|---|---
H-2065| 110/17,6 V| 240 w| 2,2 a| 6 a

REFERENCES

1-800-295-5510
uline.mx

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>