COLBOR CL60R RGB COB Video Light RGB User Manual

COLBOR CL60R RGB COB Video Light RGB

• Thank you for choosing the COLBOR product. Please read this manual carefully before use and follow all instructions mentioned herein.

Safety Instructions

• Please read and fully understand this manual before using the product.
• Please remove the COB protective film to avoid damage by overheat before first use.
• Please remove the COB protective cover to avoid damage by overheat before every use.
• Do not use the product in a moist environment or with wet hands. Do not allow the product to be splashed or soaked in water.
• Keep the product away from corrosive chemicals and liquid to avoid damage.
• Keep the product out of children’s reach during use. Do not leave the product unattended.
• When the product is working, the COB and heat sink will produce high temperatures. Do not block, turn upside down and touch with your hands.
• To ensure the service life, the cooling system still runs for a while after shutdown until the COB is below 45℃.
• Please disconnect the power supply and put away the power cord when it is not in use.
• During use, arrange the power cord in order to avoid tripping and cutting off the power or damaging the product.
• Let the product cool completely before storage. Remove the power cable from the product and put it in the corresponding position of the carrying bag after cooling down.
• Do not disassemble the product by yourself, otherwise, the warranty will be invalid. If any fault occurs, please refer it to an authorized technician for inspection or maintenance.
• Recommend to use the original parts of COLBOR. If the product is damaged due to the use of the non-original parts, it is not included in the warranty of our products.
• Drop or external impact may cause product failure. Artificial damage is not covered by warranty.
• COLBOR reserves the right to the final interpretation of the products. The product design and specifications are subject to change without notice.

Product Instructions

1. COB Bead
2. Bead Radiator (Air Outlet)
3. Bowen Mount Adapter (BAR1)
4. Ejector Pin
5. Rail
6. Air Vent (Air Intake)
7. Quick-mount Holder (EC Stand)
8. LCD Display Screen
9. Up Control Wheel
10. Down Control Wheel
11. Setting (SET) Button
12. Light Effect Frequency (RATE) Button
13. Light Effect Mode (EFF) Button
14. Light Mode ( MODE) Button
15. Type-C Power Input
16. Power Button
17. Color Indicator bar

Installation & Disassembly

Remove the COB protective cover

• Hold the COB protective cover and pull it out as the arrow shows.
• Note: Make sure to remove the cover before every use to avoid heat damage.

Install adapter and reflector

• Align the inner frame of the adapter ring with the outer frame of light, and push the adapter ring into the light from the head. Fasten two marbles on the adapter ring to the chute.
• When disassembling, push the adapter ring towards the head of the light.
• Align the reflector with the adapter ring and insert it. The ejector pin is pinched by the reflector. Rotate the reflector tightly clockwise and the ejector pin springs back.
• When disassembling, push the ejector pin and rotate the reflector anticlockwise.

Fixing of the video light

1. Slide the quick-mount holder into the chute under the light and rotate the knob tightly.
2. Install the tripod into the quick-mount holder and rotate the knob b tightly.
3. Adjust the light to the desired angle and rotate the knob c tightly.
4. Multi-light connection & disassembly
   • Slide the rail of one light into the chute of the other until the pins are inlaying. When disconnecting, slide the light out of the chute.
5. Install VM2
   • Slide VM2 into the chute of light, determine the fixed position, and adjust the lever to lock.
   • When removing, adjust the level to unlock and slide out of the light.
6. Power supply
7. Fixing power cables

  * Screw the power cable fixing clip, put the cable into the groove, and then align the bracket with the tightening screw.
2. DC power supply Connect the power adapter with the Type-C power input and turn it on.
3. Battery power supply Turn on power after installing the V-mount and battery. 

Power adapter (PA90) and V-port battery power cable (VC50) are only for powering CL60, CL60M, and CL60R, not for other electronic devices. If any damage is caused by the wrong use, it is not within our warranty.

Operation Instructions

1. Before using the product for the first time, please be sure to tear off the protective film in front of the COB bead.
2. Power   On: connect the power cord with the power adapter, plug the connector of adapter into the fixture’s power input, and then attach it to an electricity supply.
3. Function: Long press the power button, then the power button lights up. The product enters the operation interface.

• (Factory default mode: CCT)
• Power Off: press the power button.

Status Icon Description

CCT Mode (Short press CCT Mode Button to enter)

• When adjusting parameters, the screen will enlarge the value of the current setting parameters, and it will automatically return to the main screen after 1.5 seconds without any operation.

HSI MODE (Short press MODE button to switch CCT/HSI MODE)

EFF-CCT mode (Short press the EFF mode button to enter EFF mode and default EFF-CCT)

EFF-HSI mode (short press the EFF mode button, short press the up wheel to switch the EFF-HSI mode)

Settings

1. Short press the Settings Button to enter the settings menu.
2. Roll the Brightness Control Wheel to choose the setting.
3. Roll the Color Temperature Control Wheel to adjust the corresponding setting (Wireless connection adjust needs a short press).

• When the Group function is on, if the product is operated after a period of time, it takes time to connect between products, so there will be a millisecond delay.
• The effective distance of the transmitter(TX), receiver (RX), transmitter & receiver (TXRX) is 10 meters.
• The repeater (RP) function is the auxiliary function to enhance the signal of light control and the effective distance of light control. However, too many uses of the RP function can affect product response time due to environmental factors.
• If the distance between lights in a group is more than 10 meters, it is recommended to set a light in the middle as a signal RP point to increase the control distance.
• In addition, in the state of multi-light connection, the response of the product can be effectively improved when the RP functions.
• If one light is turned on if connected lights are more than five, the RP the function of two lights is turned on if there are more than ten, and so on.
• Restore factory settings: Long press two wheels together for 5 seconds and the product reboots to restore the factory default mode.

Specifications

Packaging List

• The power adapter will vary according to different regions.

About Product

1. After the test, the product with an assembly structure has a bearing capacity of 4kg. Customers need to use it according to actual conditions.
2. It is recommended to use the original power adapter for the power supply.
   • The malfunction will not be included in the warranty if other equipment is to power the product.
3. When more than five lights are assembled into a light matrix, turning on the RP function in one of them provides better control stability. If the number of lights reaches 10, enable the RP function for two of them, and so on.

More functions of COLBOR

• https://www.colborlight.com/pages/colbor-apps-download
• Scan the above QR code to the webpage and download the relevant apps, so that you can benefit from more functions such as remote light control and firmware upgrades.

WARRANTY

Warranty Period

Thank you for purchasing COLBOR products.

1. Customers are entitled to free replacement or repair service in case of the quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original COLBOR products are entitled to a 12-month limited warranty service.

• The warranty period begins on the date of purchase of brand-new, unused products by the first end-user.
• Within the warranty period, if a product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).

Warranty Exclusions and Limitations

1. Faults resulted from inappropriate use of a product without following its operation specification
2. Artificial damage, e.g. crash, squeeze, scratch, soaking, exposure to rain or damp
3. Modifications to a product by its user or a third party without prior written consent of COLBOR, e.g. replacement of element or circuit, label alteration
4. The code on the product is inconsistent with that of the warranty certificate, or the code on the product or warranty certificate is altered or torn off
5. All consumable accessories attached to a product, like a cable, cover
6. Faults as a result of force majeure, such as fire, flood, lightning, etc.

Warranty Claim Procedure

1. If failure or any problem occurs with your product after purchase, please contact a local agent for assistance, or you can always contact COLBOR’s customer service through email.
2. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
3. If the COLBOR product is out of warranty coverage, the service and the cost of the parts will be charged.

Form 1 Illumination

2700K

| Light Base| LUX| 5336| 1415| 248
FC| 496| 131| 23
Reflector| LUX| 53015| 17135| 1944
FC| 4934| 1599| 181

3200K

| Light Base| LUX| 6038| 1587| 268
FC| 561| 147| 25
Reflector| LUX| 60375| 19550| 2128
FC| 5612| 1817| 198

4300K

| Light Base| LUX| 7418| 1886| 322
FC| 689| 176| 30
Reflector| LUX| 71300| 22195| 2438
FC| 6624| 2070| 227

5600K

| Light Base| LUX| 7993| 2082| 345
FC| 743| 193| 32
Reflector| LUX| 75900| 22655| 2461
FC| 7050| 2105| 229

6500K

| Light Base| LUX| 8390| 2217| 361
FC| 781| 205| 33
Reflector| LUX| 79084| 22974| 2477
FC| 7344| 2129| 230

R

| Light Base| LUX| 1541| 442| 83
FC| 144| 41| 8
Reflector| LUX| 8556| 1530| 200
FC| 796| 141| 19

G

| Light Base| LUX| 4393| 1150| 194
FC| 408| 107| 18
Reflector| LUX| 23345| 4336| 443
FC| 2174| 403| 41

B

| Light Base| LUX| 788| 223| 47
FC| 73| 21| 4
Reflector| LUX| 4658| 1010| 117
FC| 432| 94| 11

• The data is given from testing in a laboratory.

WARRANTY CERTIFICATE

Please register your warranty. Meanwhile, you are welcome to contact us via Email.

• USER
• INFORMATION SALES
• INFORMATION REPAIR RECORD
• Customer Name:
• Phone Number:
• Email:
• Address:
• Sales Date:
• Model:
• Product Code:
• Service Date:
• Technician:
• Issue:
• RESULT
• Solved
• Unsolved
• Returned(Replaced)
• Guangzhou Zhiying Technology Co., Ltd
• Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000
• support@colborlight.com
• www.colborlight.com

Documents / Resources

| COLBOR CL60R RGB COB Video Light RGB [pdf] User Manual
CL60R RGB COB Video Light RGB, CL60R, RGB COB Video Light RGB, COB Video Light RGB, Video Light RGB, Light RGB, RGB
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>