SureCall Fusion2GO 3.0 4G Extreme RV Signal Booster Kit User Guide
- June 7, 2024
- SureCall
Table of Contents
Fusion2GO ™ 3.0RV
All-Carrier RV Cellular Signal Booster Kit
User Guide
Thank you for purchasing SureCall’s Fusion2Go-RV cell phone signal booster
kit. Fusion2Go-RV provides enhanced voice, text, and data signals for any
recreational vehicle.
If you have any questions during setup, please reach out to our US-based
experienced support technicians:
- Call: 1-888-365-6283
- Email: support@surecall.com
- Or, chat: www.surecall.com, 7:00 AM – 5:00 PM PST, Monday – Friday
How It Works
The SureCall Fusion2Go-RV is a high-quality bidirectional booster that
enhances cellular signals for motor homes, and other large vehicles.
The Fusion2Go-RV works with two antennas:
- An inside antenna that communicates with your cell phone.
- An outside antenna that communicates with the cell tower.
Signals sent from a cell tower are received by the outside antenna, amplified by the booster, and then sent to your cell phone via the inside antenna. When your phone transmits, the signal is sent to the inside antenna, and then sent to the cell tower via the outside antenna. A minimum amount of cellular reception is required for the Fusion2Go-RV to work properly.
Package Contents
-
Unpack all package contents. For missing or damaged items, contact your reseller.
-
Turn over the signal booster and record the model and serial number for reference:
Serial #:……….
Purchase Date:……………… -
Keep the carton and packing material to store the product in case you need to return it.
-
Your Fusion2Go 3.0 RV signal booster package includes the following items:
» 1. One complete Fusion2Go 3.0 vehicle booster kit
» Plus RV adapting kit -
AC power adapter
-
Inside whip antenna
-
Outside Omni antenna
-
Coax cable, SC-240, 40ft
Installation
Step 1: Mount Outside Antenna
Before you begin, please note that your installation may require the use of a
mast or RV mounting system on which to mount the outside antenna. One has not
been provided and may be obtained by a 3rd party.
The provided antenna is omnidirectional, which receives and sends signals in a
360º radius. Mount the antenna at the highest possible elevation and in an
upright position.
Cable Whip Antenna Ensure that the mounting area has at least a 12-inch radius
clear of obstructions and other radiating elements.
Fusion2Go 3.0
Installation:
- Assemble the L-Bracket with U-bolts, brackets, nuts, and washers and secure to mast. as shown in the illustration
- Remove all three screws from the antenna base
- Secure antenna to the horizontal plate of L-Bracket using screws.
- Connect one end of the provided coax cable to the antenna and tighten the connection.
Step 2. Install the Signal Booster
- Connect the inside whip antenna to the port on the side of the booster labeled “INSIDE”.
- Mount the booster within a cabinet or on a side panel close to a power source. Note that the Inside antenna and sends signals in a 360-degree radius. The antenna should be aimed vertically. The location you select should generally be in the center of where the signal is needed and also avoid excessive heat, direct sunlight, or moisture, as well as, provide proper ventilation.
- Route the cable from the outside antenna inside and connect to the port on the booster labeled “OUTSIDE”.
Step 3. Connect Power
Connect the DC power adapter to the signal booster and plug it into a power
outlet. The Power LED will light, indicating that the signal booster is ready
for use.
LED Indicators
Place a call in a location you have previously experienced poor signal and confirm that your phone is receiving a boosted signal. Normal operation is indicated by Green LEDs (both flashing and solid). In the event Red LEDs appear, antenna adjustments may be needed.
Color | Condition | Indication |
---|---|---|
Green | Solid | Indicates normal operation. |
Green | Flashing | Normal operation. This indicates that Automatic Gain Control |
(AGC) is self-adjusting due to over-signal or antenna proximity.
Red| Flashing| Indicates issues caused by overpowering or oscillation.
Adjustment of your outside antenna placement is likely needed. Verify that it
has sufficient separation from the inside antenna, as well as, any potentially
interfering objects or antennas
Note that the booster case may become warm during operation. This is normal.
WARNING. The booster is rated for 5-15V input voltage. DO NOT use the
booster with a higher voltage power supply. This can damage the booster and/or
cause personal injury.
Troubleshooting
Problem | Resolution |
---|---|
Signal booster has no power | Verify that the Power LED is ON. |
Connect the power supply to an alternate power source.
Verify that the power source is operational and the fuse is intact.
If it remains OFF, contact tech support at:
1-888-365-6283 or
supportesurecall.com
After completing installation. signal has not Improved| Verify that cable
connections are tightly fitted to the booster. Try further separating the
antennas.
Remember. Bars are not always a reliable measure of the signal. The best way to confirm signal coverage is the ability to place and hold a call.
Specifications
Product: | Fusion2Go 3.0 RV US | FusIon2Go 3.0 RV Canada |
---|---|---|
Uplink Frequency Range (MHz): | 698-716 / 776-787 / 824-849 / 1850-1915 / |
1710-1755 (G Bock Included)
Downlink Frequency Range (MHz):| 728-746 / 746-757 / 869-894 / 1930-1995 /
2110-2155 (G Block Included)
Supported Standards:| CDMA. WCDMA. GSM. EDGE. HSPA+. EVDO. LTE and all
cellular standards
Input ‘ Output Impedance:| 50 0
Maximum Gain:| 50 dB
Noise Figure:| .tr. 5 dB
VWSR:| s 2.0
Gain Adjustment:| 20 dB (Automatic)
DC Power:| 6-15V
Maximum Output Power:| 1 Watt EIRP
Cable:| SC-240
RF Connectors:| FME Male (both ends)
Power Consumption:| s 10W
Operation Temperature:| -4° to +158° F
Dimensions:| 5.625 x 4 x 1.125 inches
Weight:| 1.43 lbs
Certifications:| FCC ID: RSNF2GO3| IC: 7784A-F2G03
FCC 15.105 Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Antenna Kitting Information
Component | Prod No. Description | Gain |
---|---|---|
LTE-A | LTE-V | 800 MHz |
Vehicle
Outdoor Antenna and Cable’| SC-202W and SC174-12.5 ft (12.5 ft)| -3.16 dB|
-5.15 dB| -5.65 dB| -2.85 dB| -3.34 dB / NG
Outdoor Antenna and Cable’| SC200W and SC174-10 ft (10 ft)| -2.3 dB| -2.3 dB|
-2.3 dB| -5.8 dB| -3.98 / -5.96 dB
Indoor Antenna and Cable’| SC I IOW and SC I 74-10 ft (10 ft)| -2.7 dB| -2.7
dB| -3.2 dB| -5.8 dB| -3.98 / -5.96 dB
Marine
Outdoor Antenna and Cable’| SC288W or Galaxy 5412-P and SC240-40FN (40 ft)|
-0.52 dB| -0.52 dB| -0.98 dB| -2.52 dB| -2.12 / -2.92 dB
Indoor Antenna and Cable| SC248W Panel and SC240-20FN (20 ft)| 4.94 dB| 4.94
dB| 4.71 dB| 6.44 dB| 6.64 / 6.24 dB
Indoor Antenna and Cable| 50302W and SC240-20FN (20 ft)| 0.44 dB| 0.44 dB|
0.71 dB| 1.44 dB| 0.64 / 1.24 dB
Desktop / RV
Outdoor Antenna and Cable’| SC288W and SC240-40FN (40 ft)| -0.52 dB| -0.52 dB|
-0.98 dB| -2.52 dB| -2.12 / -2.92 dB
Indoor Antenna| SC120W whip| 1.2 dB| 1.2 dB| 1.2 dB| 3 dB| 3/ 3dB
Indoor Antenna and Cable| 50302W and SC240-20FN (20 ft)| 0.44 dB| 0.44 dB|
0.71 dB| 1.44 dB| 0.64 / 1.24 dB
*All equivalent antennas and cables are suitable for use with the Fusion2Go 3.0
| PreAGC| PreAGC
---|---|---
| Pulse GSM| 4.1 MHz AWGN
Frequency (MHz)| Input (dBm)| Output (dBm)| Gain (dB)| Input (dBm)| Output
(dBm)| Gain (dB)
Uplink: 1710-1755| -27.| 20.0| 47.| -25.| 21.| 46.0
Uplink: 1850-1915| -26.| 21.| 47.| -26.| 20.| 46.
Uplink: 824-849| -25.| 22.| 48.| -22.| 26.| 47.
Uplink: 698-716| -24.| 28.0| 47.| -20.| 27.| 47.
Uplink: 777-787| -21.| 26.| 47.| -21.| 26.| 46.
Downlink: 2110-2155| -49.| -4.| 45.| -49.| -5.| 45.
Downlink: 1930-1995| -46.| 1.0| 47.| -47.| 0.2| 47.
Downlink: 869-894| -51.| -6.| 46.| -52.| -6.| 46.
Downlink: 728-746| –48.0| 0.| 48.| -48.| -2.| 47.
Downlink: 746-757| -49.| -3.| 47.| -51.| -4.| 41.
Warning: Unauthorized antennas, cables, and/or coupling devices are
prohibited by FCC new rules. Changes or modifications not expressly approved
by SureCall could void the user’s authority to operate the equipment.
FCC 27.50(d)(4) Statement: Fixed, mobile and portable (hand-held)
stations operating in the 1720-1755 MHz band are limited 1 Watt EIRP.
Fixed stations operating in this band are limited to a maximum antenna height
of 10 meters above the ground. Mobile and portable stations operating in this
band must employ a means for limiting power to the minimum necessary for
successful communications.
Consumer Guidelines
This is a CONSUMER device
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have
your provider’s consent. Most wireless providers consent to the use of signal
boosters. Some providers may not consent to the use of this device on their
network. If you are unsure, contact your provider.
In Canada, BEFORE USE you must meet all requirements set out in ISED
CPC-2-1-05
You MUST operate this device with approved antennas and cables as specified by
the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from
(i.e. MUST NOT be installed within 20 cm of) any person.
You MUST cease operation of this device immediately if requested by the FCC
(or ISED in Canada) or a licensed wireless service provider.
WARNING: E911 location information may not be provided or may be
inaccurate for calls served by using this device.
Register your cellular booster with your wireless carrier at the following
urls:
Verizon: http://www.verizonwireless.com/wcms/consumer/register-signal-
booster.html
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
T-Mobile: https://support.t-mobile.com/docs/DOC-9827
Sprint: https://www.sprint.com/legal/fcc_boosters.html
U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-
registration.jsp
CAN ICES-3 (B)/NMB-3(B) (Canada) :
This Class B digital apparatus meets all requirements of the Canadian
Interference Causing Equipment Regulations. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation
The Manufacturer’s rated output power of this equipment is for single carrier
operation. For situations when multiple carrier signals are present, the
rating would have to be reduced by 3.5 dB, especially where the output signal
is re-radiated and can cause interference to adjacent band users. This power
reduction is to be by means of input power or gain reduction and not by an
attenuator at the output of the device.
- For details on the requirements specified in ISED CPC-2-1-05, visit: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html
Warranty
Three-Year Product Warranty
Activate your manufacturer’s 3-year warranty at
www.SureCall.com/activate
SureCall warrants its products for three years from the date of purchase
against defects in workmanship and/or materials. Specifications are subject to
change. The three-year warranty only applies to products meeting the latest
FCC Certification Guidelines stated on 2/20/2013 and going into effect April
30, 2014. A two-year warranty applies to any products manufactured before May
1, 2014.
Products returned by customers must be in their original, unmodified
condition, shipped in the original or protective packaging with proof-of-
purchase documentation enclosed, and a Return Merchandise Authorization (RMA)
number printed clearly on the outside of the shipping container.
Buyers may obtain an RMA number for warranty returns by calling the SureCall
Return Department toll-free at
1-888-365-6283. Any returns received by
SureCall without an RMA number clearly printed on the outside of the shipping
container will be returned to the sender. In order to receive full credit for
signal boosters, all accessories originally included in the signal booster box
must be returned with the signal booster. (The Buyer does not need to include
accessories sold in addition to the signal booster, such as antennas or
cables.)
This warranty does not apply to any product determined by SureCall to have
been subjected to misuse, abuse, neglect, or mishandling that alters or
damages the product’s physical or electronic properties.
SureCall warrants to the Buyer that each of its products, when shipped, will
be free from defects in material and workmanship, and will perform in full
accordance with applicable specifications. The limit of liability under this
warranty is, at SureCall’s option, to repair or replace any product or part
thereof which was purchased up to THREE YEARS after May 1, 2014 or TWO YEARS
for products purchased before May 1, 2014, as determined by examination by
SureCall, prove defective in material and/or workmanship. Warranty returns
must first be authorized in writing by SureCall. Disassembly of any SureCall
product by anyone other than an authorized representative of SureCall voids
this warranty in its entirety.
SureCall reserves the right to make changes in any of its products without
incurring any obligation to make the same changes on previously delivered
products.
As a condition to the warranties provided for herein, the Buyer will prepay
the shipping charges for all products returned to SureCall for repair, and
SureCall will pay the return shipping with the exception of products returned
from outside the United States, in which case the Buyer will pay the shipping
charges.
The Buyer will pay the cost of inspecting and testing any goods returned under
the warranty or otherwise, which are found to meet the applicable
specifications or which are not defective or not covered by this warranty.
Products sold by SureCall shall not be considered defective or non-conforming
to the Buyer’s order if they satisfactorily fulfill the performance
requirements that were published in the product specification literature, or
in accordance with samples provided by SureCall. This warranty shall not apply
to any products or parts thereof which have been subject to accident,
negligence, alteration, abuse, or misuse. SureCall makes no warranty
whatsoever in respect to accessories or parts not supplied by it.
Limitations of Warranty, Damages and Liability:
EXCEPT AS EXPRESSLY SET FORTH HEREIN, THERE ARE NO WARRANTIES, CONDITIONS,
GUARANTEES, OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHER WARRANTIES, CONDITIONS, GUARANTEES, OR REPRESENTATIONS,
WHETHER EXPRESSED OR IMPLIED, IN LAW OR IN FACT, ORAL OR IN WRITING.
SURECALL AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE
PAYMENT, IF ANY, RECEIVED BY CELLPHONEMATE, INC. FOR THE UNIT OF PRODUCT OR
SERVICE FURNISHED OR TO BE FURNISHED, AS THE CASE MAY BE, WHICH IS THE SUBJECT
OF CLAIM OR DISPUTE. IN NO EVENT SHALL RECALL BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, OR SPECIAL DAMAGES, HOWSOEVER CAUSED.
All matters regarding this warranty shall be interpreted in accordance with the laws of the State of California, and any controversy that cannot be settled directly shall be settled by arbitration in California in accordance with the rules then prevailing of the American Arbitration Association, and judgment upon the award rendered may be entered in any court having jurisdiction thereof. If one or more provisions provided herein are held to be invalid or unenforceable under applicable law, then such provision shall be ineffective and excluded to the extent of such invalidity or unenforceability without affecting in any way the remaining provisions hereof.
8346 Milmont Drive Fremont,
California 94538,
USA 888.365.6283
www.surecall.com
SureCall has made a good faith effort to ensure the accuracy of the
information in this document and disclaims the implied warranties of
merchantability and fitness for a particular purpose and makes no express
warranties, except as may be stated in its written agreement with and for its
customers. SureCall shall not be held liable to anyone for any indirect,
special or consequential damages due to omissions or errors. The information
and specifications in this document are subject to change without notice.
© 2018. All Rights Reserved. All trademarks and registered trademarks are the
property of their respective owners.
SureCall
48346 Milmont Drive
Fremont, CA 94538 USA
www.SureCall.com | 888.365.6283 |
support@surecall.com
References
- Cell Phone Signal Boosters | Get Better Cell Signal | SureCall
- Activate Your SureCall Warranty
- Register a signal booster | T-Mobile Support
- T-Mobile® Official Site: Get Even More Without Paying More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>