TELTONIKA Networks RUT360 Industrial LTE Router User Guide

June 7, 2024
TELTONIKA Networks

TELTONIKA logo

Quick Start Guide v1.3
RUT360

TELTONIKA Networks RUT360 Industrial LTE Router -
Symbol

Wiki Knowledge base

https://wiki.teltonika-networks.com/

TELTONIKA Networks RUT360 Industrial LTE Router - view

POWER SOCKET PINOUT

TELTONIKA Networks RUT360 Industrial LTE Router - POWER SOCKET
PINOUT

I/O (PIN 3 and 4): Configurable digital Input/Output pins. Open collector output, max output 30 V, 300 mA or Digital input where 0-6 V detected as a logic low and 8-30 V – logic high.

HARDWARE INSTALLATION

  1. Push the SIM holder button with the SIM needle.
  2. Pull out the SIM holder.
  3. Insert your SIM card into the SIM holder.
  4. Slide the SIM holder back into the router.
  5. Attach Mobile and WiFi antennas.
  6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
  7. Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to the LAN port.

TELTONIKA Networks RUT360 Industrial LTE Router -
Hardware

LOGIN TO DEVICE

  1. To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
  2. Use login information shown in image A when prompted for authentication.
  3. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory and you will not be able to interact with the router’s WebUI before you change the password.
  4. When you change the router’s password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the router’s main operating parameters.
  5. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

TELTONIKA Networks RUT360 Industrial LTE Router - LOGIN TO
DEVICE

TECHNICAL INFORMATION

Radio specifications

RF technologies| 3G, 4G, WiFi
Max RF power| 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi
**Bundled accessories specifications*
Power adapter| Input: 0.45 A@100-240 VAC, Output: 12 VDC, 1 A, 4 pin plug
Mobile antenna| 698-960/1710-2690 MHz, 50 0, VSWR<3, gain
4 dBi, omnidirectional, SMA male connector
WiFi antenna| 2400-2483.5 MHz, 50 0, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for compliance with the legal regulations.

SAFETY INFORMATION

RUT360 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.
Hereby, TELTONIKA NETWORKS declares that this RUT360 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following Internet address: https://wiki.teltonika- networks.com/view/RUT360_CE/RED
Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to configure it. More information on https://wiki.teltonika-networks.com/

This sign means that all used electronic and electric equipment should not be mixed with general household waste.

This sign means that the product meets the requirements of the applicable EU directives.

©2020 Teltonika Networks
www.teltonika-networks.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

TELTONIKA Networks User Manuals

Related Manuals