LARK 83194 4 Light Pendant or Canopy Light Instruction Manual

: June 3, 2024
: LARK

Table of Contents

LARK 83194 4 Light Pendant or Canopy Light
Mounting Instructions
INSTALLATION
wiring instructions
grounding instructions
ABOUT COMPANY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LARK 83194 4 Light Pendant or Canopy Light

LARK 83194 4 Light Pendant or Canopy Light-fig1

Mounting Instructions

start here

Find a clear area in which you can work.
Unpack ﬁxture and glass from carton.
Carefully review instructions prior to assembly.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS-18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION

IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

To begin installation it is necessary to determine the quan-tity and length of mounting stems you will need to hang your fixture at the proper height. Your fixture is supplied with 2-12” stems and 1-6” stem. If more stems are required please go to hinkley.com to order.
Secure assembled stems to canopy swiviel (L)
Slide screw collar ring (S), from canopy swivel (L) over the attached stems. This is followed by the canopy (C) – see Drawing 1
Now slip wires through the center of swivel (L) attached to mounting strap (A). Then thread swivel with mounting strap into the top stem.
Now lift fixture up to ceiling and attach mounting strap (A) to junction box (J) using two 8-32 screws (B) NOT PROVIDED
Now make all wiring connections following instruc-tion sheet (IS-18) provided. After wiring connections are completed, tuck wires into junction box.
Now slip canopy up to ceiling. While holding canopy in place slip screw collar ring (S) up to canopy and thread onto swivel (L) to secure canopy to ceiling.
Assembly is complete and fixture can be lamped accordingly.

SAFETY WARNING: READ WIRING AND GROUNDING
INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING Is REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Cover open end of connectors with silicone sealant to form a watertight seal.
- If installing a wall mount ﬁxture, use caulk to seal gaps between the ﬁxture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a ﬁxture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the ﬁxture ground wire (E) (typically copper or green plastic coated) to the ﬁxture mounting strap (M) with the ground screw (S) – see Drawing 1.
Note: On straps for screw supported ﬁxtures, ﬁrst install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop ﬁxture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on ﬁxture mounting strap (M) and connect to the loose end of the ﬁxture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.
Post-Mount Fixtures
Connect ﬁxture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.