Lark 81520BK Rhett LED Wall Mount Instructions
- May 15, 2024
- LARK
Table of Contents
Lark 81520BK Rhett LED Wall Mount
Product Specifications
- Item No: 81520
- Manufacturer: Lark
- Model: 33000
- Power Supply: Electrical
- Fixture Type: Indoor/Outdoor
Product Usage Instructions
Mounting Instructions
- Find a clear working area.
- Unpack the fixture and glass from the carton.
- Carefully review the assembly instructions.
- Prepare mounting strap (A) by threading the two long mounting screws (B) into the back of the mounting strap. The side with the ground screw head is the front.
- Attach mounting strap (A) to junction box (J) using two screws (C) (not provided).
- Install the fixture following safety warnings and electrical wiring instructions.
Cage Installation Instructions
- Mount fixture by slipping the two mounting screws (B) through the holes in the backplate (E).
- Thread the ball knobs (F) onto the mounting screws and tighten.
Glass Installation Instructions
- Lamp fixture with an appropriate medium base bulb.
- Place glass panels (6) into the cage (3).
- Fold glass tabs (5) down to secure the glass panels.
- Secure the cage (3) to the fixture top (1) using screws (2).
Frequently Asked Questions
Q: Can I install this fixture outdoors?
A: Yes, this fixture can be installed outdoors. Please follow the outdoor
fixtures wiring instructions provided in the manual.
Q: Is professional installation required?
A: While professional installation is recommended, you can install this
fixture yourself by carefully following the provided instructions and safety
guidelines.
Q: What should I do if I encounter difficulties during installation?
A: If you face any challenges during installation, consult a qualified
electrician or contact our customer support for assistance.
Assembly Instructions
Start here
- Find a clear area in which you can work.
- Unpack fixture and glass from carton.
- Carefully review instructions prior to assembly
- Prepare mounting strap (A) by threading the two long mounting screws (B) into the back of the mounting strap. The side of the mounting strap that the head of the ground screw is on, is the front -see Drawing 1.
- Be sure the holes into which the screws are threaded match the spacing of holes (D) in the back plate (E).
- Attach mounting strap (A) to junction box (J) using two screws (C) NOT PROVIDED.
- Fixture can now be installed.
SAFETY WARNING:
READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL
DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS
REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE
REQUIREMENTS.
Make electrical connections from supply wire to fixture lead wires. Refer to
instruction sheet (I.S. 18) and follow all instructions to make all necessary
wiring connections. Then refer back to this sheet to complete installation of
this fixture
- To mount fixture, slip the two mounting screws (B) through the two mounting holes (D) in the backplate (E) – see Drawing 1.
- While holding fixture in place, thread the ball knobs (F) on to the end of the mounting screws (B), and tighten
- Lamp fixture using appropriate medium base bulb (4)
- Place glass panels (6) into cage (3)
- Fold glass tabs (5) down to secure glass (6)
- Secure cage (3) to fixture top (1) using screws (2)
Wiring grounding instructions
SAFETY WARNING :
READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL
DIRECTIONS.TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS
REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE
REQUIREMENTS
Indoor Fixtures
- Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
- Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Please refer to the grounding instructions below to complete all electrical connections
Outdoor Fixtures
- Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector — see Drawings 2 or 3.
- Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Cover the open end of connectors with silicone sealant to form a watertight seal.
- If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
- Please refer to the grounding instructions below to complete all electrical connections.
Grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture
ground wire (E) (typically copper or green plastic coated) to the fixture
mounting strap (M) with the ground screw (S) – see Drawing 1.
Note : On straps for screw-supported fixtures, first install the two
mounting screws in the strap. Any remaining tapped hole may be used for the
ground screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under
the head of the ground screw (S) on the fixture mounting strap (M) and connect
to the loose end of the fixture ground wire directly to the ground wire of the
building system with appropriately sized twist-on connectors – see Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to
the power supply ground with an appropriately sized twist-on connector inside
the post. Cover the open end of the connector with silicone sealant to form a
watertight seal – see Drawing 3.
IS200 Caulking Instructions
After securing the fixture to the wall it is recommended that the gap between the wall and the fixture backplate be sealed on the top and both sides, with a good quality waterproof caulk or silicone sealant (NOT INCLUDED) – see Drawing
After securing the fixture in place it is recommended that the gap between the
mounting top and fixture base be sealed with any good quality waterproof caulk
or silicone sealant (not included). It is also recommended that a small bead
of caulk or sealant be put under the ball knobs used to mount the fixture –
see Drawing 2
LARK 33000 PIN OAK PARKWAY, AVON LAKE, OH 44012 LarkLiving.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>